community.network.flowadm module – Manage bandwidth resource control and priority for protocols, services and zones on Solaris/illumos systems

Note

This module is part of the community.network collection (version 5.0.3).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install community.network.

To use it in a playbook, specify: community.network.flowadm.

Synopsis

  • Create/modify/remove networking bandwidth and associated resources for a type of traffic on a particular link.

Aliases: network.illumos.flowadm

Parameters

Parameter

Comments

dsfield

string

  • Identifies the 8-bit differentiated services field (as defined in RFC 2474). The optional dsfield_mask is used to state the bits of interest in the differentiated services field when comparing with the dsfield value. Both values must be in hexadecimal.

string

Specifiies a link to configure flow on.

local_ip

string

Identifies a network flow by the local IP address.

local_port

string

Identifies a service specified by the local port.

maxbw

string

  • Sets the full duplex bandwidth for the flow. The bandwidth is specified as an integer with one of the scale suffixes(K, M, or G for Kbps, Mbps, and Gbps). If no units are specified, the input value will be read as Mbps.

name

aliases: flow

string / required

  • A flow is defined as a set of attributes based on Layer 3 and Layer 4 headers, which can be used to identify a protocol, service, or a zone.

priority

string

Sets the relative priority for the flow.

Choices:

  • "low"

  • "medium" ← (default)

  • "high"

remote_ip

string

Identifies a network flow by the remote IP address.

state

string

Create/delete/enable/disable an IP address on the network interface.

Choices:

  • "absent"

  • "present" ← (default)

  • "resetted"

temporary

boolean

Specifies that the configured flow is temporary. Temporary flows do not persist across reboots.

Choices:

  • false ← (default)

  • true

transport

string

  • Specifies a Layer 4 protocol to be used. It is typically used in combination with local_port to identify the service that needs special attention.

Examples

- name: Limit SSH traffic to 100M via vnic0 interface
  community.network.flowadm:
    link: vnic0
    flow: ssh_out
    transport: tcp
    local_port: 22
    maxbw: 100M
    state: present

- name: Reset flow properties
  community.network.flowadm:
    name: dns
    state: resetted

- name: Configure policy for EF PHB (DSCP value of 101110 from RFC 2598) with a bandwidth of 500 Mbps and a high priority
  community.network.flowadm:
    link: bge0
    dsfield: '0x2e:0xfc'
    maxbw: 500M
    priority: high
    flow: efphb-flow
    state: present

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key

Description

dsfield

string

flow’s differentiated services value

Returned: if dsfield is defined

Sample: "0x2e:0xfc"

string

flow’s link

Returned: if link is defined

Sample: "vnic0"

local_Ip

string

flow’s local IP address

Returned: if local_ip is defined

Sample: "10.0.0.42"

local_port

integer

flow’s local port

Returned: if local_port is defined

Sample: 1337

maxbw

string

flow’s maximum bandwidth

Returned: if maxbw is defined

Sample: "100M"

name

string

flow name

Returned: always

Sample: "http_drop"

priority

string

flow’s priority

Returned: if priority is defined

Sample: "low"

remote_Ip

string

flow’s remote IP address

Returned: if remote_ip is defined

Sample: "10.0.0.42"

state

string

state of the target

Returned: always

Sample: "present"

temporary

boolean

flow’s persistence

Returned: always

Sample: true

transport

string

flow’s transport

Returned: if transport is defined

Sample: "tcp"

Authors

  • Adam Števko (@xen0l)