netapp_eseries.santricity.na_santricity_mgmt_interface module – NetApp E-Series manage management interface configuration

Note

This module is part of the netapp_eseries.santricity collection (version 1.4.1).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install netapp_eseries.santricity.

To use it in a playbook, specify: netapp_eseries.santricity.na_santricity_mgmt_interface.

Synopsis

  • Configure the E-Series management interfaces

Parameters

Parameter

Comments

address

string

The IPv4 address to assign to the interface.

Should be specified in xx.xx.xx.xx form.

Mutually exclusive with config_method=dhcp

api_password

string / required

The password to authenticate with the SANtricity Web Services Proxy or Embedded Web Services API.

api_url

string / required

The url to the SANtricity Web Services Proxy or Embedded Web Services API.

Example https://prod-1.wahoo.acme.com:8443/devmgr/v2

api_username

string / required

The username to authenticate with the SANtricity Web Services Proxy or Embedded Web Services API.

config_method

string

The configuration method type to use for network interface ports.

dhcp is mutually exclusive with address, subnet_mask, and gateway.

Choices:

  • "dhcp"

  • "static"

controller

string / required

The controller that owns the port you want to configure.

Controller names are represented alphabetically, with the first controller as A, the second as B, and so on.

Current hardware models have either 1 or 2 available controllers, but that is not a guaranteed hard limitation and could change in the future.

Choices:

  • "A"

  • "B"

dns_address

string

Primary IPv4 or IPv6 DNS server address

dns_address_backup

string

Secondary IPv4 or IPv6 DNS server address

dns_config_method

string

The configuration method type to use for DNS services.

dhcp is mutually exclusive with dns_address, and dns_address_backup.

Choices:

  • "dhcp"

  • "static"

gateway

string

The IPv4 gateway address to utilize for the interface.

Should be specified in xx.xx.xx.xx form.

Mutually exclusive with config_method=dhcp

ntp_address

string

Primary IPv4, IPv6, or FQDN NTP server address

ntp_address_backup

string

Secondary IPv4, IPv6, or FQDN NTP server address

ntp_config_method

string

The configuration method type to use for NTP services.

disable is mutually exclusive with ntp_address and ntp_address_backup.

dhcp is mutually exclusive with ntp_address and ntp_address_backup.

Choices:

  • "disabled"

  • "dhcp"

  • "static"

port

integer

The ethernet port configuration to modify.

The channel represents the port number left to right on the controller, beginning with 1.

Required when config_method is specified.

ssh

boolean

Enable ssh access to the controller for debug purposes.

This is a controller-level setting.

rlogin/telnet will be enabled for ancient equipment where ssh is not available.

Choices:

  • false

  • true

ssid

string

The ID of the array to manage. This value must be unique for each array.

Default: "1"

state

string

Enable or disable IPv4 network interface configuration.

Either IPv4 or IPv6 must be enabled otherwise error will occur.

Assumed to be state==enabled when config_method is specified unless defined.

Choices:

  • "enabled"

  • "disabled"

subnet_mask

string

The subnet mask to utilize for the interface.

Should be specified in xx.xx.xx.xx form.

Mutually exclusive with config_method=dhcp

validate_certs

boolean

Should https certificates be validated?

Choices:

  • false

  • true ← (default)

Notes

Note

  • Check mode is supported.

  • It is highly recommended to have a minimum of one up management port on each controller.

  • When using SANtricity Web Services Proxy, use netapp_eseries.santricity.na_santricity_storage_system to update management paths. This is required because of a known issue and will be addressed in the proxy version 4.1. After the resolution the management ports should automatically be updated.

  • The interface settings are applied synchronously, but changes to the interface itself (receiving a new IP address via dhcp, etc), can take seconds or minutes longer to take effect.

  • The E-Series Ansible modules require either an instance of the Web Services Proxy (WSP), to be available to manage the storage-system, or an E-Series storage-system that supports the Embedded Web Services API.

  • Embedded Web Services is currently available on the E2800, E5700, EF570, and newer hardware models.

  • netapp_eseries.santricity.netapp_e_storage_system may be utilized for configuring the systems managed by a WSP instance.

Examples

- name: Configure the first port on the A controller with a static IPv4 address
  na_santricity_mgmt_interface:
    ssid: "1"
    api_url: "https://192.168.1.100:8443/devmgr/v2"
    api_username: "admin"
    api_password: "adminpass"
    validate_certs: true
    port: "1"
    controller: "A"
    config_method: static
    address: "192.168.1.100"
    subnet_mask: "255.255.255.0"
    gateway: "192.168.1.1"

- name: Disable ipv4 connectivity for the second port on the B controller
  na_santricity_mgmt_interface:
    ssid: "1"
    api_url: "https://192.168.1.100:8443/devmgr/v2"
    api_username: "admin"
    api_password: "adminpass"
    validate_certs: true
    port: "2"
    controller: "B"
    enable_interface: no

- name: Enable ssh access for ports one and two on controller A
  na_santricity_mgmt_interface:
    ssid: "1"
    api_url: "https://192.168.1.100:8443/devmgr/v2"
    api_username: "admin"
    api_password: "adminpass"
    validate_certs: true
    port: "1"
    controller: "A"
    ssh: yes

- name: Configure static DNS settings for the first port on controller A
  na_santricity_mgmt_interface:
    ssid: "1"
    api_url: "https://192.168.1.100:8443/devmgr/v2"
    api_username: "admin"
    api_password: "adminpass"
    validate_certs: true
    port: "1"
    controller: "A"
    dns_config_method: static
    dns_address: "192.168.1.100"
    dns_address_backup: "192.168.1.1"

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key

Description

available_embedded_api_urls

list / elements=string

List containing available web services embedded REST API urls

Returned: on success

msg

string

Success message

Returned: on success

Sample: "The interface settings have been updated."

Authors

  • Michael Price (@lmprice)

  • Nathan Swartz (@swartzn)

  • Vu Tran (@VuTran007)