cisco.ios.ios_l2_interfaces – L2 interfaces resource module

Note

This plugin is part of the cisco.ios collection (version 1.3.0).

To install it use: ansible-galaxy collection install cisco.ios.

To use it in a playbook, specify: cisco.ios.ios_l2_interfaces.

New in version 1.0.0: of cisco.ios

Synopsis

  • This module provides declarative management of Layer-2 interface on Cisco IOS devices.

Note

This module has a corresponding action plugin.

Parameters

Parameter Choices/Defaults Comments
config
list / elements=dictionary
A dictionary of Layer-2 interface options
access
dictionary
Switchport mode access command to configure the interface as a layer 2 access.
vlan
integer
Configure given VLAN in access port. It's used as the access VLAN ID.
mode
string
    Choices:
  • access
  • trunk
Mode in which interface needs to be configured.
An interface whose trunk encapsulation is "Auto" can not be configured to "trunk" mode.
name
string / required
Full name of the interface excluding any logical unit number, i.e. GigabitEthernet0/1.
trunk
dictionary
Switchport mode trunk command to configure the interface as a Layer 2 trunk. Note The encapsulation is always set to dot1q.
allowed_vlans
list / elements=string
List of allowed VLANs in a given trunk port. These are the only VLANs that will be configured on the trunk.
encapsulation
string
    Choices:
  • dot1q
  • isl
  • negotiate
Trunking encapsulation when interface is in trunking mode.
native_vlan
integer
Native VLAN to be configured in trunk port. It's used as the trunk native VLAN ID.
pruning_vlans
list / elements=string
Pruning VLAN to be configured in trunk port. It's used as the trunk pruning VLAN ID.
voice
dictionary
Switchport mode voice command to configure the interface with a voice vlan.
vlan
integer
Configure given voice VLAN on access port. It's used as the voice VLAN ID.
running_config
string
This option is used only with state parsed.
The value of this option should be the output received from the IOS device by executing the command show running-config | section ^interface.
The state parsed reads the configuration from running_config option and transforms it into Ansible structured data as per the resource module's argspec and the value is then returned in the parsed key within the result.
state
string
    Choices:
  • merged ←
  • replaced
  • overridden
  • deleted
  • rendered
  • gathered
  • parsed
The state the configuration should be left in
The states rendered, gathered and parsed does not perform any change on the device.
The state rendered will transform the configuration in config option to platform specific CLI commands which will be returned in the rendered key within the result. For state rendered active connection to remote host is not required.
The state gathered will fetch the running configuration from device and transform it into structured data in the format as per the resource module argspec and the value is returned in the gathered key within the result.
The state parsed reads the configuration from running_config option and transforms it into JSON format as per the resource module parameters and the value is returned in the parsed key within the result. The value of running_config option should be the same format as the output of command show running-config | include ip route|ipv6 route executed on device. For state parsed active connection to remote host is not required.

Notes

Note

  • Tested against Cisco IOSv Version 15.2 on VIRL.

Examples

# Using merged

# Before state:
# -------------
#
# viosl2#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  negotiation auto
# interface GigabitEthernet0/2
#  description This is test
#  switchport access vlan 20
#  media-type rj45
#  negotiation auto

- name: Merge provided configuration with device configuration
  cisco.ios.ios_l2_interfaces:
    config:
    - name: GigabitEthernet0/1
      mode: access
      access:
        vlan: 10
      voice:
        vlan: 40
    - name: GigabitEthernet0/2
      mode: trunk
      trunk:
        allowed_vlans: 10-20,40
        native_vlan: 20
        pruning_vlans: 10,20
        encapsulation: dot1q
    state: merged

# After state:
# ------------
#
# viosl2#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  switchport access vlan 10
#  switchport voice vlan 40
#  switchport mode access
#  negotiation auto
# interface GigabitEthernet0/2
#  description This is test
#  switchport trunk allowed vlan 10-20,40
#  switchport trunk encapsulation dot1q
#  switchport trunk native vlan 20
#  switchport trunk pruning vlan 10,20
#  switchport mode trunk
#  media-type rj45
#  negotiation auto

# Using replaced

# Before state:
# -------------
#
# viosl2#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  switchport access vlan 20
#  negotiation auto
# interface GigabitEthernet0/2
#  description This is test
#  switchport access vlan 20
#  media-type rj45
#  negotiation auto

- name: Replaces device configuration of listed l2 interfaces with provided configuration
  cisco.ios.ios_l2_interfaces:
    config:
    - name: GigabitEthernet0/2
      trunk:
        allowed_vlans: 20-25,40
        native_vlan: 20
        pruning_vlans: 10
        encapsulation: isl
    state: replaced

# After state:
# -------------
#
# viosl2#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  switchport access vlan 20
#  negotiation auto
# interface GigabitEthernet0/2
#  description This is test
#  switchport trunk allowed vlan 20-25,40
#  switchport trunk encapsulation isl
#  switchport trunk native vlan 20
#  switchport trunk pruning vlan 10
#  media-type rj45
#  negotiation auto

# Using overridden

# Before state:
# -------------
#
# viosl2#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  switchport trunk encapsulation dot1q
#  switchport trunk native vlan 20
#  negotiation auto
# interface GigabitEthernet0/2
#  description This is test
#  switchport access vlan 20
#  switchport trunk encapsulation dot1q
#  switchport trunk native vlan 20
#  media-type rj45
#  negotiation auto

- name: Override device configuration of all l2 interfaces with provided configuration
  cisco.ios.ios_l2_interfaces:
    config:
    - name: GigabitEthernet0/2
      access:
        vlan: 20
      voice:
        vlan: 40
    state: overridden

# After state:
# -------------
#
# viosl2#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  negotiation auto
# interface GigabitEthernet0/2
#  description This is test
#  switchport access vlan 20
#  switchport voice vlan 40
#  media-type rj45
#  negotiation auto

# Using Deleted

# Before state:
# -------------
#
# viosl2#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  switchport access vlan 20
#  negotiation auto
# interface GigabitEthernet0/2
#  description This is test
#  switchport access vlan 20
#  switchport trunk allowed vlan 20-40,60,80
#  switchport trunk encapsulation dot1q
#  switchport trunk native vlan 10
#  switchport trunk pruning vlan 10
#  media-type rj45
#  negotiation auto

- name: Delete IOS L2 interfaces as in given arguments
  cisco.ios.ios_l2_interfaces:
    config:
    - name: GigabitEthernet0/1
    state: deleted

# After state:
# -------------
#
# viosl2#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  negotiation auto
# interface GigabitEthernet0/2
#  description This is test
#  switchport access vlan 20
#  switchport trunk allowed vlan 20-40,60,80
#  switchport trunk encapsulation dot1q
#  switchport trunk native vlan 10
#  switchport trunk pruning vlan 10
#  media-type rj45
#  negotiation auto


# Using Deleted without any config passed
#"(NOTE: This will delete all of configured resource module attributes from each configured interface)"

# Before state:
# -------------
#
# viosl2#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  switchport access vlan 20
#  negotiation auto
# interface GigabitEthernet0/2
#  description This is test
#  switchport access vlan 20
#  switchport trunk allowed vlan 20-40,60,80
#  switchport trunk encapsulation dot1q
#  switchport trunk native vlan 10
#  switchport trunk pruning vlan 10
#  media-type rj45
#  negotiation auto

- name: Delete IOS L2 interfaces as in given arguments
  cisco.ios.ios_l2_interfaces:
    state: deleted

# After state:
# -------------
#
# viosl2#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  negotiation auto
# interface GigabitEthernet0/2
#  description This is test
#  media-type rj45
#  negotiation auto

# Using Gathered

# Before state:
# -------------
#
# vios#sh running-config | section ^interface
# interface GigabitEthernet0/1
#  switchport access vlan 10
# interface GigabitEthernet0/2
#  switchport trunk allowed vlan 10-20,40
#  switchport trunk encapsulation dot1q
#  switchport trunk native vlan 10
#  switchport trunk pruning vlan 10,20
#  switchport mode trunk

- name: Gather listed l2 interfaces with provided configurations
  cisco.ios.ios_l2_interfaces:
    config:
    state: gathered

# Module Execution Result:
# ------------------------
#
# "gathered": [
#         {
#             "name": "GigabitEthernet0/0"
#         },
#         {
#             "access": {
#                 "vlan": 10
#             },
#             "name": "GigabitEthernet0/1"
#         },
#         {
#             "mode": "trunk",
#             "name": "GigabitEthernet0/2",
#             "trunk": {
#                 "allowed_vlans": [
#                     "10-20",
#                     "40"
#                 ],
#                 "encapsulation": "dot1q",
#                 "native_vlan": 10,
#                 "pruning_vlans": [
#                     "10",
#                     "20"
#                 ]
#             }
#         }
#     ]

# After state:
# ------------
#
# vios#sh running-config | section ^interface
# interface GigabitEthernet0/1
#  switchport access vlan 10
# interface GigabitEthernet0/2
#  switchport trunk allowed vlan 10-20,40
#  switchport trunk encapsulation dot1q
#  switchport trunk native vlan 10
#  switchport trunk pruning vlan 10,20
#  switchport mode trunk

# Using Rendered

- name: Render the commands for provided  configuration
  cisco.ios.ios_l2_interfaces:
    config:
    - name: GigabitEthernet0/1
      access:
        vlan: 30
    - name: GigabitEthernet0/2
      trunk:
        allowed_vlans: 10-20,40
        native_vlan: 20
        pruning_vlans: 10,20
        encapsulation: dot1q
    state: rendered

# Module Execution Result:
# ------------------------
#
# "rendered": [
#         "interface GigabitEthernet0/1",
#         "switchport access vlan 30",
#         "interface GigabitEthernet0/2",
#         "switchport trunk encapsulation dot1q",
#         "switchport trunk native vlan 20",
#         "switchport trunk allowed vlan 10-20,40",
#         "switchport trunk pruning vlan 10,20"
#     ]

# Using Parsed

# File: parsed.cfg
# ----------------
#
# interface GigabitEthernet0/1
# switchport mode access
# switchport access vlan 30
# interface GigabitEthernet0/2
# switchport trunk allowed vlan 15-20,40
# switchport trunk encapsulation dot1q
# switchport trunk native vlan 20
# switchport trunk pruning vlan 10,20

- name: Parse the commands for provided configuration
  cisco.ios.ios_l2_interfaces:
    running_config: "{{ lookup('file', 'parsed.cfg') }}"
    state: parsed

# Module Execution Result:
# ------------------------
#
# "parsed": [
#         {
#             "access": {
#                 "vlan": 30
#             },
#             "mode": "access",
#             "name": "GigabitEthernet0/1"
#         },
#         {
#             "name": "GigabitEthernet0/2",
#             "trunk": {
#                 "allowed_vlans": [
#                     "15-20",
#                     "40"
#                 ],
#                 "encapsulation": "dot1q",
#                 "native_vlan": 20,
#                 "pruning_vlans": [
#                     "10",
#                     "20"
#                 ]
#             }
#         }
#     ]

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
after
list / elements=string
when changed
The configuration as structured data after module completion.

Sample:
The configuration returned will always be in the same format of the parameters above.
before
list / elements=string
always
The configuration as structured data prior to module invocation.

Sample:
The configuration returned will always be in the same format of the parameters above.
commands
list / elements=string
always
The set of commands pushed to the remote device

Sample:
['interface GigabitEthernet0/1', 'switchport access vlan 20']


Authors

  • Sumit Jaiswal (@justjais)