cisco.nxos.nxos_ospfv3 – OSPFv3 resource module

Note

This plugin is part of the cisco.nxos collection (version 1.4.0).

To install it use: ansible-galaxy collection install cisco.nxos.

To use it in a playbook, specify: cisco.nxos.nxos_ospfv3.

New in version 1.2.0: of cisco.nxos

Synopsis

• This module manages OSPFv3 configuration on devices running Cisco NX-OS.

Note

This module has a corresponding action plugin.

Parameters

Parameter								Choices/Defaults	Comments
config dictionary									A list of OSPFv3 process configuration.
	processes list / elements=dictionary								A list of OSPFv3 instances' configurations.
		address_family dictionary							IPv6 unicast address-family OSPFv3 settings.
			afi string					Choices: ipv6	Configure OSPFv3 settings under IPv6 address-family.
			areas list / elements=dictionary						Configure properties of OSPF Areas under address-family.
				area_id string / required					The Area ID as an integer or IP Address.
				default_cost integer					Specify the default cost.
				filter_list list / elements=dictionary					Filter prefixes between OSPF areas.
					direction string / required			Choices: in out	The direction to apply the route map.
					route_map string / required				The Route-map name.
				ranges list / elements=dictionary					Configure an address range for the area.
					cost integer				Cost to use for the range.
					not_advertise boolean			Choices: no yes	Suppress advertising the specified range.
					prefix string / required				IP in Prefix format (x.x.x.x/len)
			default_information dictionary						Control distribution of default routes.
				originate dictionary					Distribute a default route.
					always boolean			Choices: no yes	Always advertise a default route.
					route_map string				Policy to control distribution of default routes
					set boolean			Choices: no yes	Enable distribution of default route.
			distance integer						Configure the OSPF administrative distance.
			maximum_paths integer						Maximum paths per destination.
			redistribute list / elements=dictionary						Redistribute information from another routing protocol.
				id string					The identifier for the protocol specified.
				protocol string / required				Choices: bgp direct eigrp isis lisp ospfv3 rip static	The name of the protocol.
				route_map string / required					The route map policy to constrain redistribution.
			safi string					Choices: unicast	Configure OSPFv3 settings under IPv6 unicast address-family.
			summary_address list / elements=dictionary						Configure route summarization for redistribution.
				not_advertise boolean				Choices: no yes	Supress advertising the specified summary.
				prefix string / required					IPv6 prefix format 'xxxx:xxxx/ml', 'xxxx:xxxx::/ml' or 'xxxx::xx/128'
				tag integer					A 32-bit tag value.
			table_map dictionary						Policy for filtering/modifying OSPF routes before sending them to RIB.
				filter boolean				Choices: no yes	Block the OSPF routes from being sent to RIB.
				name string / required					The Route Map name.
			timers dictionary						Configure timer related constants.
				throttle dictionary					Configure throttle related constants.
					spf dictionary				Set OSPF SPF timers.
						initial_spf_delay integer			Initial SPF schedule delay in milliseconds.
						max_wait_time integer			Maximum wait time between SPF calculations.
						min_hold_time integer			Minimum hold time between SPF calculations.
		areas list / elements=dictionary							Configure properties of OSPF Areas.
			area_id string / required						The Area ID as an integer or IP Address.
			nssa dictionary						NSSA settings for the area.
				default_information_originate boolean				Choices: no yes	Originate Type-7 default LSA into NSSA area.
				no_redistribution boolean				Choices: no yes	Do not send redistributed LSAs into NSSA area.
				no_summary boolean				Choices: no yes	Do not send summary LSAs into NSSA area.
				route_map string					Policy to control distribution of default route.
				set boolean				Choices: no yes	Configure area as NSSA.
				translate dictionary					Translate LSA.
					type7 dictionary				Translate from Type 7 to Type 5.
						always boolean		Choices: no yes	Always translate LSAs
						never boolean		Choices: no yes	Never translate LSAs
						supress_fa boolean		Choices: no yes	Suppress forwarding address in translated LSAs.
			stub dictionary						Settings for configuring the area as a stub.
				no_summary boolean				Choices: no yes	Prevent ABR from sending summary LSAs into stub area.
				set boolean				Choices: no yes	Configure the area as a stub.
		auto_cost dictionary							Calculate OSPF cost according to bandwidth.
			reference_bandwidth integer / required						Reference bandwidth used to assign OSPF cost.
			unit string / required					Choices: Gbps Mbps	Specify in which unit the reference bandwidth is specified.
		flush_routes boolean						Choices: no yes	Flush routes on a non-graceful controlled restart.
		graceful_restart dictionary							Configure graceful restart.
			grace_period integer						Configure maximum interval to restart gracefully.
			helper_disable boolean					Choices: no yes	Enable/Disable helper mode.
			planned_only boolean					Choices: no yes	Enable graceful restart only for a planned restart
			set boolean					Choices: no yes	Enable graceful-restart.
		isolate boolean						Choices: no yes	Isolate this router from OSPF perspective.
		log_adjacency_changes dictionary							Log changes in adjacency state.
			detail boolean					Choices: no yes	Notify all state changes.
			log boolean					Choices: no yes	Enable/disable logging changes in adjacency state.
		max_lsa dictionary							Feature to limit the number of non-self-originated LSAs.
			ignore_count integer						Set count on how many times adjacencies can be suppressed.
			ignore_time integer						Set time during which all adjacencies are suppressed.
			max_non_self_generated_lsa integer / required						Set the maximum number of non self-generated LSAs.
			reset_time integer						Set number of minutes after which ignore-count is reset to zero.
			threshold integer						Threshold value (%) at which to generate a warning message.
			warning_only boolean					Choices: no yes	Log a warning message when limit is exceeded.
		max_metric dictionary							Maximize the cost metric.
			router_lsa dictionary						Router LSA configuration.
				external_lsa dictionary					External LSA configuration.
					max_metric_value integer				Set max metric value for external LSAs.
					set boolean			Choices: no yes	Set external-lsa attribute.
				inter_area_prefix_lsa dictionary					Inter-area-prefix LSAs configuration.
					max_metric_value integer				Max metric value for summary LSAs.
					set boolean			Choices: no yes	Set summary-lsa attribute.
				on_startup dictionary					Effective only at startup.
					set boolean			Choices: no yes	Set on-startup attribute.
					wait_for_bgp_asn integer				ASN of BGP to wait for.
					wait_period integer				Wait period in seconds after startup.
				set boolean				Choices: no yes	Set router-lsa attribute.
				stub_prefix_lsa boolean				Choices: no yes	Advertise Max metric for Stub links as well.
		name_lookup boolean						Choices: no yes	Display OSPF router ids as DNS names.
		passive_interface dictionary							Suppress routing updates on the interface.
			default boolean					Choices: no yes	Interfaces passive by default.
		process_id string / required							The OSPF process tag.
		router_id string							Set OSPF process router-id.
		shutdown boolean						Choices: no yes	Shutdown the OSPF protocol instance.
		timers dictionary							Configure timer related constants.
			lsa_arrival integer						Mimimum interval between arrival of a LSA.
			lsa_group_pacing integer						LSA group refresh/maxage interval.
			throttle dictionary						Configure throttle related constants.
				lsa dictionary					Set rate-limiting for LSA generation.
					hold_interval integer				The hold interval.
					max_interval integer				The max interval.
					start_interval integer				The start interval.
		vrfs list / elements=dictionary							Configure VRF specific OSPF settings.
			areas list / elements=dictionary						Configure properties of OSPF Areas.
				area_id string / required					The Area ID as an integer or IP Address.
				nssa dictionary					NSSA settings for the area.
					default_information_originate boolean			Choices: no yes	Originate Type-7 default LSA into NSSA area.
					no_redistribution boolean			Choices: no yes	Do not send redistributed LSAs into NSSA area.
					no_summary boolean			Choices: no yes	Do not send summary LSAs into NSSA area.
					route_map string				Policy to control distribution of default route.
					set boolean			Choices: no yes	Configure area as NSSA.
					translate dictionary				Translate LSA.
						type7 dictionary			Translate from Type 7 to Type 5.
							always boolean	Choices: no yes	Always translate LSAs
							never boolean	Choices: no yes	Never translate LSAs
							supress_fa boolean	Choices: no yes	Suppress forwarding address in translated LSAs.
				stub dictionary					Settings for configuring the area as a stub.
					no_summary boolean			Choices: no yes	Prevent ABR from sending summary LSAs into stub area.
					set boolean			Choices: no yes	Configure the area as a stub.
			auto_cost dictionary						Calculate OSPF cost according to bandwidth.
				reference_bandwidth integer / required					Reference bandwidth used to assign OSPF cost.
				unit string / required				Choices: Gbps Mbps	Specify in which unit the reference bandwidth is specified.
			graceful_restart dictionary						Configure graceful restart.
				grace_period integer					Configure maximum interval to restart gracefully.
				helper_disable boolean				Choices: no yes	Enable/Disable helper mode.
				planned_only boolean				Choices: no yes	Enable graceful restart only for a planned restart
				set boolean				Choices: no yes	Enable graceful-restart.
			log_adjacency_changes dictionary						Log changes in adjacency state.
				detail boolean				Choices: no yes	Notify all state changes.
				log boolean				Choices: no yes	Enable/disable logging changes in adjacency state.
			max_lsa dictionary						Feature to limit the number of non-self-originated LSAs.
				ignore_count integer					Set count on how many times adjacencies can be suppressed.
				ignore_time integer					Set time during which all adjacencies are suppressed.
				max_non_self_generated_lsa integer / required					Set the maximum number of non self-generated LSAs.
				reset_time integer					Set number of minutes after which ignore-count is reset to zero.
				threshold integer					Threshold value (%) at which to generate a warning message.
				warning_only boolean				Choices: no yes	Log a warning message when limit is exceeded.
			max_metric dictionary						Maximize the cost metric.
				router_lsa dictionary					Router LSA configuration.
					external_lsa dictionary				External LSA configuration.
						max_metric_value integer			Set max metric value for external LSAs.
						set boolean		Choices: no yes	Set external-lsa attribute.
					inter_area_prefix_lsa dictionary				Inter-area-prefix LSAs configuration.
						max_metric_value integer			Max metric value for summary LSAs.
						set boolean		Choices: no yes	Set summary-lsa attribute.
					on_startup dictionary				Effective only at startup.
						set boolean		Choices: no yes	Set on-startup attribute.
						wait_for_bgp_asn integer			ASN of BGP to wait for.
						wait_period integer			Wait period in seconds after startup.
					set boolean			Choices: no yes	Set router-lsa attribute.
					stub_prefix_lsa boolean			Choices: no yes	Advertise Max metric for Stub links as well.
			name_lookup boolean					Choices: no yes	Display OSPF router ids as DNS names.
			passive_interface dictionary						Suppress routing updates on the interface.
				default boolean				Choices: no yes	Interfaces passive by default.
			router_id string						Set OSPF process router-id.
			shutdown boolean					Choices: no yes	Shutdown the OSPF protocol instance.
			timers dictionary						Configure timer related constants.
				lsa_arrival integer					Mimimum interval between arrival of a LSA.
				lsa_group_pacing integer					LSA group refresh/maxage interval.
				throttle dictionary					Configure throttle related constants.
					lsa dictionary				Set rate-limiting for LSA generation.
						hold_interval integer			The hold interval.
						max_interval integer			The max interval.
						start_interval integer			The start interval.
			vrf string / required						Name/Identifier of the VRF.
running_config string									This option is used only with state parsed. The value of this option should be the output received from the NX-OS device by executing the command show running-config | section "^router ospfv3". The state parsed reads the configuration from running_config option and transforms it into Ansible structured data as per the resource module's argspec and the value is then returned in the parsed key within the result.
state string								Choices: merged ← replaced overridden deleted gathered parsed rendered	The state the configuration should be left in.

Notes

Note

• Tested against NX-OS 7.0(3)I5(1).

• This module works with connection network_cli and httpapi.

Examples

# Using merged

# Before state:
# -------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# nxos-9k-rdo#

- name: Merge the provided configuration with the exisiting running configuration
  cisco.nxos.nxos_ospfv3:
    config:
      processes:
      - process_id: 100
        router_id: 203.0.113.20
      - process_id: 102
        router_id: 198.51.100.1
        address_family:
          afi: ipv6
          safi: unicast
          areas:
          - area_id: 0.0.0.100
            filter_list:
            - route_map: rmap_1
              direction: in
            - route_map: rmap_2
              direction: out
            ranges:
            - prefix: 2001:db2::/32
              not_advertise: true
            - prefix: 2001:db3::/32
              cost: 120
          redistribute:
          - protocol: eigrp
            id: 120
            route_map: rmap_1
          - protocol: direct
            route_map: ospf102-direct-connect
        vrfs:
        - vrf: zone1
          router_id: 198.51.100.129
          areas:
          - area_id: 0.0.0.102
            nssa:
              default_information_originate: true
              no_summary: true
          - area_id: 0.0.0.103
            nssa:
              no_summary: true
              translate:
                type7:
                  always: true
        - vrf: zone2
          auto_cost:
            reference_bandwidth: 45
            unit: Gbps
    state: merged

# Task output
# -------------
# before: {}
#
# commands:
#  - router ospf 102
#  - router-id 198.51.100.1
#  - address-family ipv6 unicast
#  - redistribute eigrp 120 route-map rmap_1
#  - redistribute direct route-map ospf102-direct-connect
#  - area 0.0.0.100 filter-list route-map rmap_1 in
#  - area 0.0.0.100 filter-list route-map rmap_2 out
#  - area 0.0.0.100 range 2001:db2::/32 not-advertise
#  - area 0.0.0.100 range 2001:db3::/32 cost 120
#  - vrf zone1
#  - router-id 198.51.100.129
#  - area 0.0.0.102 nssa no-summary default-information-originate
#  - area 0.0.0.103 nssa no-summary
#  - area 0.0.0.103 nssa translate type7 always
#  - vrf zone2
#  - auto-cost reference-bandwidth 45 Gbps
#  - router ospf 100
#  - router-id 203.0.113.20
#
# after:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv4
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: out
#            route_map: rmap_2
#          - direction: in
#            route_map: rmap_1
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#          - cost: 120
#            prefix: 2001:db3::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "120"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
#   router-id 203.0.113.20
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family ipv6 unicast
#     redistribute direct route-map ospf102-direct-connect
#     redistribute eigrp 120 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_2 out
#     area 0.0.0.100 filter-list route-map rmap_1 in
#     area 0.0.0.100 range 2001:db2::/32 not-advertise
#     area 0.0.0.100 range 2001:db3::/32 cost 120
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

# Using replaced

# Before state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
#   router-id 203.0.113.20
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family upv6 unicast
#     redistribute direct route-map ospf102-direct-connect
#     redistribute eigrp 120 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_2 out
#     area 0.0.0.100 filter-list route-map rmap_1 in
#     area 0.0.0.100 range 2001:db2::/32 not-advertise
#     area 0.0.0.100 range 2001:db3::/32 cost 120
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

- name: Replace device configurations of listed OSPFv3 processes with provided configurations
  cisco.nxos.nxos_ospfv3:
    config:
      processes:
      - process_id: 102
        router_id: 198.51.100.1
        address_family:
          afi: ipv6
          safi: unicast
          areas:
          - area_id: 0.0.0.100
            filter_list:
            - route_map: rmap_8
              direction: in
            ranges:
            - not_advertise: true
              prefix: 2001:db2::/32
          redistribute:
          - protocol: eigrp
            id: 130
            route_map: rmap_1
          - protocol: direct
            route_map: ospf102-direct-connect
        vrfs:
        - vrf: zone1
          router_id: 198.51.100.129
          areas:
          - area_id: 0.0.0.102
            nssa:
              default_information_originate: True
              no_summary: True
    state: replaced

# Task output
# -------------
# before:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv4
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: out
#            route_map: rmap_2
#          - direction: in
#            route_map: rmap_1
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#          - cost: 120
#            prefix: 2001:db3::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "120"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#
#  commands:
#  - router ospf 102
#  - address-family ipv6 unicast
#  - redistribute eigrp 130 route-map rmap_1
#  - no redistribute eigrp 120 route-map rmap_1
#  - area 0.0.0.100 filter-list route-map rmap_8 in
#  - no area 0.0.0.100 filter-list route-map rmap_2 out
#  - no area 0.0.0.100 range 2001:db3::/32
#  - vrf zone1
#  - no area 0.0.0.103 nssa
#  - no area 0.0.0.103 nssa translate type7 always
#  - no vrf zone2
#
# after:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv6
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: in
#            route_map: rmap_8
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "130"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        router_id: 198.51.100.129
#        vrf: zone1

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
#   router-id 203.0.113.20
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family ipv6 unicast
#     redistribute direct route-map ospf102-direct-connect
#     redistribute eigrp 130 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_8 in
#     area 0.0.0.100 range 198.51.100.64/27 not-advertise
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate

# Using overridden

# Before state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
#   router-id 203.0.113.20
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family ipv6 unicast
#     redistribute direct route-map ospf102-direct-connect
#     redistribute eigrp 120 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_2 out
#     area 0.0.0.100 filter-list route-map rmap_1 in
#     area 0.0.0.100 range 2001:db2::/32 not-advertise
#     area 0.0.0.100 range 2001:db3::/32 cost 120
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

- name: Overridde all OSPFv3 configuration with provided configuration
  cisco.nxos.nxos_ospfv3:
    config:
      processes:
      - process_id: 104
        router_id: 203.0.113.20
      - process_id: 102
        router_id: 198.51.100.1
        shutdown: true
    state: overridden

# Task output
# -------------
# before:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv4
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: out
#            route_map: rmap_2
#          - direction: in
#            route_map: rmap_1
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#          - cost: 120
#            prefix: 2001:db3::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "120"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#
# commands:
#  - no router ospfv3 100
#  - router ospfv3 104
#  - router-id 203.0.113.20
#  - router ospfv3 102
#  - shutdown
#  - address-family ipv6 unicast
#  - no redistribute direct route-map ospf102-direct-connect
#  - no redistribute eigrp 120 route-map rmap_1
#  - no area 0.0.0.100 filter-list route-map rmap_2 out
#  - no area 0.0.0.100 filter-list route-map rmap_1 in
#  - no area 0.0.0.100 range 2001:db2::/32
#  - no area 0.0.0.100 range 2001:db3::/32
#  - no vrf zone1
#  - no vrf zone2
#
# after:
#    processes:
#    - process_id: "102"
#      router_id: 198.51.100.1
#      shutdown: true
#      address_family:
#        afi: ipv6
#        safi: unicast
#    - process_id: "104"
#      router_id: 203.0.113.20

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family ipv6 unicast
#   shutdown
# router ospfv3 104
#   router-id 203.0.113.20

# Using deleted to delete a single OSPF process

# Before state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospf .*"
# router ospfv3 100
#   router-id 203.0.113.20
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family ipv6 unicast
#     redistribute direct route-map ospf102-direct-connect
#     redistribute eigrp 120 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_2 out
#     area 0.0.0.100 filter-list route-map rmap_1 in
#     area 0.0.0.100 range 2001:db2::/32 not-advertise
#     area 0.0.0.100 range 2001:db3::/32 cost 120
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

- name: Delete a single OSPFv3 process
  cisco.nxos.nxos_ospfv3:
    config:
      processes:
      - process_id: 102
    state: deleted

# Task output
# -------------
# before:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv4
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: out
#            route_map: rmap_2
#          - direction: in
#            route_map: rmap_1
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#          - cost: 120
#            prefix: 2001:db3::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "120"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#
# commands:
#  - no router ospfv3 102
#
# after:
#   processes:
#   - process_id: "100"
#     router_id: 203.0.113.20

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
#   router-id 203.0.113.20

# Using deleted all OSPFv3 processes from the device

# Before state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
#   router-id 203.0.113.20
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family ipv6 unicast
#     redistribute direct route-map ospf102-direct-connect
#     redistribute eigrp 120 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_2 out
#     area 0.0.0.100 filter-list route-map rmap_1 in
#     area 0.0.0.100 range 2001:db2::/32 not-advertise
#     area 0.0.0.100 range 2001:db3::/32 cost 120
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

- name: Delete all OSPFv3 processes from the device
  cisco.nxos.nxos_ospfv3:
    state: deleted

# Task output
# -------------
# before:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv4
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: out
#            route_map: rmap_2
#          - direction: in
#            route_map: rmap_1
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#          - cost: 120
#            prefix: 2001:db3::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "120"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#
# commands:
#  - no router ospfv3 100
#  - no router ospfv3 102
#
#  after: {}

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# nxos-9k-rdo#

# Using rendered

- name: Merge the provided configuration with the exisiting running configuration
  cisco.nxos.nxos_ospfv3:
    config:
      processes:
      - process_id: 100
        router_id: 203.0.113.20
      - process_id: 102
        router_id: 198.51.100.1
        address_family:
          afi: ipv6
          safi: unicast
          areas:
          - area_id: 0.0.0.100
            filter_list:
            - route_map: rmap_1
              direction: in
            - route_map: rmap_2
              direction: out
            ranges:
            - prefix: 2001:db2::/32
              not_advertise: true
            - prefix: 2001:db3::/32
              cost: 120
          redistribute:
          - protocol: eigrp
            id: 120
            route_map: rmap_1
          - protocol: direct
            route_map: ospf102-direct-connect
        vrfs:
        - vrf: zone1
          router_id: 198.51.100.129
          areas:
          - area_id: 0.0.0.102
            nssa:
              default_information_originate: true
              no_summary: true
          - area_id: 0.0.0.103
            nssa:
              no_summary: true
              translate:
                type7:
                  always: true
        - vrf: zone2
          auto_cost:
            reference_bandwidth: 45
            unit: Gbps
    state: rendered

# Task Output (redacted)
# -----------------------
# rendered:
#  - router ospfv3 100
#  - router-id 203.0.113.20
#  - router ospfv3 102
#  - router-id 198.51.100.1
#  - address-family ipv6 unicast
#  - redistribute eigrp 120 route-map rmap_1
#  - redistribute direct route-map ospf102-direct-connect
#  - area 0.0.0.100 filter-list route-map rmap_1 in
#  - area 0.0.0.100 filter-list route-map rmap_2 out
#  - area 0.0.0.100 range 2001:db2::/32 not-advertise
#  - area 0.0.0.100 range 2001:db3::/32 cost 120
#  - vrf zone1
#  - router-id 198.51.100.129
#  - area 0.0.0.102 nssa no-summary default-information-originate
#  - area 0.0.0.103 nssa no-summary
#  - area 0.0.0.103 nssa translate type7 always
#  - vrf zone2
#  - auto-cost reference-bandwidth 45 Gbps

# Using parsed

# parsed.cfg
# ------------
# router ospfv3 100
#   router-id 192.0.100.1
#   address-family ipv6 unicast
#     redistribute direct route-map ospf-direct-connect
#     redistribute eigrp 120 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_2 out
#     area 0.0.0.100 filter-list route-map rmap_1 in
#     area 0.0.0.100 range 2001:db2::/32 not-advertise
#     area 0.0.0.100 range 2001:db3::/32 cost 120
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.100.1 nssa no-summary no-redistribution
# router ospfv3 102
#   router-id 198.54.100.1
#   shutdown

- name: Parse externally provided OSPFv3 config
  cisco.nxos.nxos_ospfv3:
    running_config: "{{ lookup('file', 'ospfv2.cfg') }}"
    state: parsed

# Task output (redacted)
# -----------------------
# parsed:
#   processes:
#   - process_id: "100"
#     address_family:
#       afi: ipv6
#       safi: unicast
#       areas:
#       - area_id: 0.0.0.101
#         nssa:
#           no_redistribution: true
#           no_summary: true
#       - area_id: 0.0.0.102
#         stub:
#           no_summary: true
#         filter_list:
#           - direction: out
#             route_map: rmap_2
#           - direction: in
#             route_map: rmap_1
#         ranges:
#           - not_advertise: true
#             prefix: 192.0.2.0/24
#           - cost: 120
#             prefix: 192.0.3.0/24
#       redistribute:
#       - protocol: direct
#         route_map: ospf-direct-connect
#       - id: "120"
#         protocol: eigrp
#         route_map: rmap_1
#     router_id: 192.0.100.1
#     vrfs:
#       - vrf: zone1
#         areas:
#           - area_id: 0.0.100.1
#             nssa:
#               no_redistribution: true
#               no_summary: true
#         router_id: 192.0.100.2
#   - process_id: "102"
#     router_id: 198.54.100.1
#     shutdown: True

# Using gathered

- name: Gather OSPFv3 facts using gathered
  cisco.nxos.nxos_ospfv3:
    state: gathered

# Task output (redacted)
# -----------------------
#  gathered:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv4
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: out
#            route_map: rmap_2
#          - direction: in
#            route_map: rmap_1
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#          - cost: 120
#            prefix: 2001:db3::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "120"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
after dictionary	when changed	The resulting configuration model invocation. Sample: The configuration returned will always be in the same format of the parameters above.
before dictionary	always	The configuration prior to the model invocation. Sample: The configuration returned will always be in the same format of the parameters above.
commands list / elements=string	always	The set of commands pushed to the remote device. Sample: ['router ospfv3 102', 'router-id 198.54.100.1', 'router ospfv3 100', 'router-id 192.0.100.1', 'address-family ipv6 unicast', 'redistribute eigrp 120 route-map rmap_1', 'redistribute direct route-map ospf-direct-connect', 'area 0.0.0.100 filter-list route-map rmap_1 in', 'area 0.0.0.100 filter-list route-map rmap_2 out', 'area 0.0.0.100 range 2001:db2::/32 not-advertise', 'area 0.0.0.100 range 2001:db3::/32 cost 120', 'vrf zone1', 'router-id 192.0.100.2', 'vrf zone2', 'auto-cost reference-bandwidth 45 Gbps']

Authors

• Nilashish Chakraborty (@NilashishC)