community.general.parted – Configure block device partitions

Note

This plugin is part of the community.general collection (version 1.3.6).

To install it use: ansible-galaxy collection install community.general.

To use it in a playbook, specify: community.general.parted.

Synopsis

• This module allows configuring block device partition using the parted command line tool. For a full description of the fields and the options check the GNU parted manual.

Requirements

The below requirements are needed on the host that executes this module.

• This module requires parted version 1.8.3 and above

• align option (except ‘undefined’) requires parted 2.1 and above

• If the version of parted is below 3.1, it requires a Linux version running the sysfs file system /sys/.

Parameters

Parameter	Choices/Defaults	Comments
align string	Choices: cylinder minimal none optimal ← undefined	Set alignment for newly created partitions. Use 'undefined' for parted default aligment.
device string / required		The block device (disk) where to operate.
flags list / elements=string		A list of the flags that has to be set on the partition.
fs_type string added in 0.2.0 of community.general		If specified and the partition does not exist, will set filesystem type to given partition. Parameter optional, but see notes below about negative negative part_start values.
label string	Choices: aix amiga bsd dvh gpt loop mac msdos ← pc98 sun	Disk label type to use. If device already contains different label, it will be changed to label and any previous partitions will be lost.
name string		Sets the name for the partition number (GPT, Mac, MIPS and PC98 only).
number integer		The number of the partition to work with or the number of the partition that will be created. Required when performing any action on the disk, except fetching information.
part_end string	Default: "100%"	Where the partition will end as offset from the beginning of the disk, that is, the "distance" from the start of the disk. Negative numbers specify distance from the end of the disk. The distance can be specified with all the units supported by parted (except compat) and it is case sensitive, e.g. 10GiB, 15%.
part_start string	Default: "0%"	Where the partition will start as offset from the beginning of the disk, that is, the "distance" from the start of the disk. Negative numbers specify distance from the end of the disk. The distance can be specified with all the units supported by parted (except compat) and it is case sensitive, e.g. 10GiB, 15%. Using negative values may require setting of fs_type (see notes).
part_type string	Choices: extended logical primary ←	May be specified only with 'msdos' or 'dvh' partition tables. A name must be specified for a 'gpt' partition table. Neither part_type nor name may be used with a 'sun' partition table.
resize boolean added in 1.3.0 of community.general	Choices: no ← yes	Call resizepart on existing partitions to match the size specified by part_end.
state string	Choices: absent present info ←	Whether to create or delete a partition. If set to info the module will only return the device information.
unit string	Choices: s B KB KiB ← MB MiB GB GiB TB TiB % cyl chs compact	Selects the current default unit that Parted will use to display locations and capacities on the disk and to interpret those given by the user if they are not suffixed by an unit. When fetching information about a disk, it is always recommended to specify a unit.

Notes

Note

• When fetching information about a new disk and when the version of parted installed on the system is before version 3.1, the module queries the kernel through /sys/ to obtain disk information. In this case the units CHS and CYL are not supported.

• Negative part_start start values were rejected if fs_type was not given. This bug was fixed in parted 3.2.153. If you want to use negative part_start, specify fs_type as well or make sure your system contains newer parted.

Examples

- name: Create a new ext4 primary partition
  community.general.parted:
    device: /dev/sdb
    number: 1
    state: present
    fs_type: ext4

- name: Remove partition number 1
  community.general.parted:
    device: /dev/sdb
    number: 1
    state: absent

- name: Create a new primary partition with a size of 1GiB
  community.general.parted:
    device: /dev/sdb
    number: 1
    state: present
    part_end: 1GiB

- name: Create a new primary partition for LVM
  community.general.parted:
    device: /dev/sdb
    number: 2
    flags: [ lvm ]
    state: present
    part_start: 1GiB

- name: Create a new primary partition with a size of 1GiB at disk's end
  community.general.parted:
    device: /dev/sdb
    number: 3
    state: present
    fs_type: ext3
    part_start: -1GiB

# Example on how to read info and reuse it in subsequent task
- name: Read device information (always use unit when probing)
  community.general.parted: device=/dev/sdb unit=MiB
  register: sdb_info

- name: Remove all partitions from disk
  community.general.parted:
    device: /dev/sdb
    number: '{{ item.num }}'
    state: absent
  loop: '{{ sdb_info.partitions }}'

- name: Extend an existing partition to fill all available space
  community.general.parted:
    device: /dev/sdb
    number: "{{ sdb_info.partitions | length }}"
    part_end: "100%"
    resize: true
    state: present

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key		Returned	Description
partition_info complex		success	Current partition information Sample: {'disk': {'dev': '/dev/sdb', 'logical_block': 512, 'model': 'VMware Virtual disk', 'physical_block': 512, 'size': 5.0, 'table': 'msdos', 'unit': 'gib'}, 'partitions': [{'begin': 0.0, 'end': 1.0, 'flags': ['boot', 'lvm'], 'fstype': '', 'name': '', 'num': 1, 'size': 1.0}, {'begin': 1.0, 'end': 5.0, 'flags': [], 'fstype': '', 'name': '', 'num': 2, 'size': 4.0}], 'script': 'unit KiB print '}
	disk dictionary	success	Generic device information.
	partitions list / elements=string	success	List of device partitions.
	script string	success	parted script executed by module

Authors

• Fabrizio Colonna (@ColOfAbRiX)