community.network.netscaler_lb_vserver – Manage load balancing vserver configuration

Note

This plugin is part of the community.network collection (version 1.3.2).

To install it use: ansible-galaxy collection install community.network.

To use it in a playbook, specify: community.network.netscaler_lb_vserver.

Synopsis

• Manage load balancing vserver configuration

• This module is intended to run either on the ansible control node or a bastion (jumpserver) with access to the actual netscaler instance

Requirements

The below requirements are needed on the host that executes this module.

• nitro python sdk

Parameters

Parameter		Choices/Defaults	Comments
appflowlog string		Choices: enabled disabled	Apply AppFlow logging to the virtual server.
authentication boolean		Choices: no yes	Enable or disable user authentication.
authenticationhost string			Fully qualified domain name (FQDN) of the authentication virtual server to which the user must be redirected for authentication. Make sure that the Authentication parameter is set to yes. Minimum length = 3 Maximum length = 252
authn401 boolean		Choices: no yes	Enable or disable user authentication with HTTP 401 responses.
authnprofile string			Name of the authentication profile to be used when authentication is turned on.
authnvsname string			Name of an authentication virtual server with which to authenticate users. Minimum length = 1 Maximum length = 252
backuplbmethod string		Choices: ROUNDROBIN LEASTCONNECTION LEASTRESPONSETIME SOURCEIPHASH LEASTBANDWIDTH LEASTPACKETS CUSTOMLOAD	Backup load balancing method. Becomes operational if the primary load balancing me thod fails or cannot be used. Valid only if the primary method is based on static proximity.
backuppersistencetimeout string			Time period for which backup persistence is in effect. Minimum value = 2 Maximum value = 1440
bypassaaaa boolean		Choices: no yes	If this option is enabled while resolving DNS64 query AAAA queries are not sent to back end dns server.
cacheable boolean		Choices: no yes	Route cacheable requests to a cache redirection virtual server. The load balancing virtual server can forward requests only to a transparent cache redirection virtual server that has an IP address and port combination of *:80, so such a cache redirection virtual server must be configured on the appliance.
clttimeout string			Idle time, in seconds, after which a client connection is terminated. Minimum value = 0 Maximum value = 31536000
comment string			Any comments that you might want to associate with the virtual server.
connfailover string		Choices: DISABLED STATEFUL STATELESS	Mode in which the connection failover feature must operate for the virtual server. After a failover, established TCP connections and UDP packet flows are kept active and resumed on the secondary appliance. Clients remain connected to the same servers. Available settings function as follows: * STATEFUL - The primary appliance shares state information with the secondary appliance, in real time, resulting in some runtime processing overhead. * STATELESS - State information is not shared, and the new primary appliance tries to re-create the packet flow on the basis of the information contained in the packets it receives. * DISABLED - Connection failover does not occur.
cookiename string			Use this parameter to specify the cookie name for COOKIE persistence type. It specifies the name of cookie with a maximum of 32 characters. If not specified, cookie name is internally generated.
datalength string			Length of the token to be extracted from the data segment of an incoming packet, for use in the token method of load balancing. The length of the token, specified in bytes, must not be greater than 24 KB. Applicable to virtual servers of type TCP. Minimum value = 1 Maximum value = 100
dataoffset string			Offset to be considered when extracting a token from the TCP payload. Applicable to virtual servers, of type TCP, using the token method of load balancing. Must be within the first 24 KB of the TCP payload. Minimum value = 0 Maximum value = 25400
dbprofilename string			Name of the DB profile whose settings are to be applied to the virtual server. Minimum length = 1 Maximum length = 127
dbslb string		Choices: enabled disabled	Enable database specific load balancing for MySQL and MSSQL service types.
disabled boolean		Choices: no ← yes	When set to yes the lb vserver will be disabled. When set to no the lb vserver will be enabled. Note that due to limitations of the underlying NITRO API a disabled state change alone does not cause the module result to report a changed status.
disableprimaryondown string		Choices: enabled disabled	If the primary virtual server goes down, do not allow it to return to primary status until manually enabled.
dns64 string		Choices: enabled disabled	This argument is for enabling/disabling the dns64 on lbvserver.
dnsprofilename string			Name of the DNS profile to be associated with the VServer. DNS profile properties will be applied to the transactions processed by a VServer. This parameter is valid only for DNS and DNS-TCP VServers. Minimum length = 1 Maximum length = 127
downstateflush string		Choices: enabled disabled	Flush all active transactions associated with a virtual server whose state transitions from UP to DOWN. Do not enable this option for applications that must complete their transactions.
hashlength string			Number of bytes to consider for the hash value used in the URLHASH and DOMAINHASH load balancing methods. Minimum value = 1 Maximum value = 4096
healththreshold string			Threshold in percent of active services below which vserver state is made down. If this threshold is 0, vserver state will be up even if one bound service is up. Minimum value = 0 Maximum value = 100
httpprofilename string			Name of the HTTP profile whose settings are to be applied to the virtual server. Minimum length = 1 Maximum length = 127
icmpvsrresponse string		Choices: PASSIVE ACTIVE	How the NetScaler appliance responds to ping requests received for an IP address that is common to one or more virtual servers. Available settings function as follows: * If set to PASSIVE on all the virtual servers that share the IP address, the appliance always responds to the ping requests. * If set to ACTIVE on all the virtual servers that share the IP address, the appliance responds to the ping requests if at least one of the virtual servers is UP. Otherwise, the appliance does not respond. * If set to ACTIVE on some virtual servers and PASSIVE on the others, the appliance responds if at least one virtual server with the ACTIVE setting is UP. Otherwise, the appliance does not respond. Note: This parameter is available at the virtual server level. A similar parameter, ICMP Response, is available at the IP address level, for IPv4 addresses of type VIP. To set that parameter, use the add ip command in the CLI or the Create IP dialog box in the GUI.
insertvserveripport string		Choices: OFF VIPADDR V6TOV4MAPPING	Insert an HTTP header, whose value is the IP address and port number of the virtual server, before forwarding a request to the server. The format of the header is <vipHeader>: <virtual server IP address>_<port number >, where vipHeader is the name that you specify for the header. If the virtual server has an IPv6 address, the address in the header is enclosed in brackets ([ and ]) to separate it from the port number. If you have mapped an IPv4 address to a virtual server's IPv6 address, the value of this parameter determines which IP address is inserted in the header, as follows: * VIPADDR - Insert the IP address of the virtual server in the HTTP header regardless of whether the virtual server has an IPv4 address or an IPv6 address. A mapped IPv4 address, if configured, is ignored. * V6TOV4MAPPING - Insert the IPv4 address that is mapped to the virtual server's IPv6 address. If a mapped IPv4 address is not configured, insert the IPv6 address. * OFF - Disable header insertion.
ipmask string			IP mask, in dotted decimal notation, for the IP Pattern parameter. Can have leading or trailing non-zero octets (for example, 255.255.240.0 or 0.0.255.255). Accordingly, the mask specifies whether the first n bits or the last n bits of the destination IP address in a client request are to be matched with the corresponding bits in the IP pattern. The former is called a forward mask. The latter is called a reverse mask.
ippattern string			IP address pattern, in dotted decimal notation, for identifying packets to be accepted by the virtual server. The IP Mask parameter specifies which part of the destination IP address is matched against the pattern. Mutually exclusive with the IP Address parameter. For example, if the IP pattern assigned to the virtual server is 198.51.100.0 and the IP mask is 255.255.240.0 (a forward mask), the first 20 bits in the destination IP addresses are matched with the first 20 bits in the pattern. The virtual server accepts requests with IP addresses that range from 198.51.96.1 to 198.51.111.254. You can also use a pattern such as 0.0.2.2 and a mask such as 0.0.255.255 (a reverse mask). If a destination IP address matches more than one IP pattern, the pattern with the longest match is selected, and the associated virtual server processes the request. For example, if virtual servers vs1 and vs2 have the same IP pattern, 0.0.100.128, but different IP masks of 0.0.255.255 and 0.0.224.255, a destination IP address of 198.51.100.128 has the longest match with the IP pattern of vs1. If a destination IP address matches two or more virtual servers to the same extent, the request is processed by the virtual server whose port number matches the port number in the request.
ipv46 string			IPv4 or IPv6 address to assign to the virtual server.
l2conn boolean		Choices: no yes	Use Layer 2 parameters (channel number, MAC address, and VLAN ID) in addition to the 4-tuple (<source IP>:<source port>::<destination IP>:<destination port>) that is used to identify a connection. Allows multiple TCP and non-TCP connections with the same 4-tuple to co-exist on the NetScaler appliance.
lbmethod string		Choices: ROUNDROBIN LEASTCONNECTION LEASTRESPONSETIME URLHASH DOMAINHASH DESTINATIONIPHASH SOURCEIPHASH SRCIPDESTIPHASH LEASTBANDWIDTH LEASTPACKETS TOKEN SRCIPSRCPORTHASH LRTM CALLIDHASH CUSTOMLOAD LEASTREQUEST AUDITLOGHASH STATICPROXIMITY	Load balancing method. The available settings function as follows: * ROUNDROBIN - Distribute requests in rotation, regardless of the load. Weights can be assigned to services to enforce weighted round robin distribution. * LEASTCONNECTION (default) - Select the service with the fewest connections. * LEASTRESPONSETIME - Select the service with the lowest average response time. * LEASTBANDWIDTH - Select the service currently handling the least traffic. * LEASTPACKETS - Select the service currently serving the lowest number of packets per second. * CUSTOMLOAD - Base service selection on the SNMP metrics obtained by custom load monitors. * LRTM - Select the service with the lowest response time. Response times are learned through monitoring probes. This method also takes the number of active connections into account. Also available are a number of hashing methods, in which the appliance extracts a predetermined portion of the request, creates a hash of the portion, and then checks whether any previous requests had the same hash value. If it finds a match, it forwards the request to the service that served those previous requests. Following are the hashing methods: * URLHASH - Create a hash of the request URL (or part of the URL). * DOMAINHASH - Create a hash of the domain name in the request (or part of the domain name). The domain name is taken from either the URL or the Host header. If the domain name appears in both locations, the URL is preferred. If the request does not contain a domain name, the load balancing method defaults to LEASTCONNECTION. * DESTINATIONIPHASH - Create a hash of the destination IP address in the IP header. * SOURCEIPHASH - Create a hash of the source IP address in the IP header. * TOKEN - Extract a token from the request, create a hash of the token, and then select the service to which any previous requests with the same token hash value were sent. * SRCIPDESTIPHASH - Create a hash of the string obtained by concatenating the source IP address and destination IP address in the IP header. * SRCIPSRCPORTHASH - Create a hash of the source IP address and source port in the IP header. * CALLIDHASH - Create a hash of the SIP Call-ID header.
listenpolicy string			Default syntax expression identifying traffic accepted by the virtual server. Can be either an expression (for example, CLIENT.IP.DST.IN_SUBNET(192.0.2.0/24) or the name of a named expression. In the above example, the virtual server accepts all requests whose destination IP address is in the 192.0.2.0/24 subnet.
listenpriority string			Integer specifying the priority of the listen policy. A higher number specifies a lower priority. If a request matches the listen policies of more than one virtual server the virtual server whose listen policy has the highest priority (the lowest priority number) accepts the request. Minimum value = 0 Maximum value = 101
m string		Choices: IP MAC IPTUNNEL TOS	Redirection mode for load balancing. Available settings function as follows: * IP - Before forwarding a request to a server, change the destination IP address to the server's IP address. * MAC - Before forwarding a request to a server, change the destination MAC address to the server's MAC address. The destination IP address is not changed. MAC-based redirection mode is used mostly in firewall load balancing deployments. * IPTUNNEL - Perform IP-in-IP encapsulation for client IP packets. In the outer IP headers, set the destination IP address to the IP address of the server and the source IP address to the subnet IP (SNIP). The client IP packets are not modified. Applicable to both IPv4 and IPv6 packets. * TOS - Encode the virtual server's TOS ID in the TOS field of the IP header. You can use either the IPTUNNEL or the TOS option to implement Direct Server Return (DSR).
macmoderetainvlan string		Choices: enabled disabled	This option is used to retain vlan information of incoming packet when macmode is enabled.
maxautoscalemembers string			Maximum number of members expected to be present when vserver is used in Autoscale. Minimum value = 0 Maximum value = 5000
minautoscalemembers string			Minimum number of members expected to be present when vserver is used in Autoscale. Minimum value = 0 Maximum value = 5000
mssqlserverversion string		Choices: 70 2000 2000SP1 2005 2008 2008R2 2012 2014	For a load balancing virtual server of type MSSQL, the Microsoft SQL Server version. Set this parameter if you expect some clients to run a version different from the version of the database. This setting provides compatibility between the client-side and server-side connections by ensuring that all communication conforms to the server's version.
mysqlcharacterset string			Character set that the virtual server advertises to clients.
mysqlprotocolversion string			MySQL protocol version that the virtual server advertises to clients.
mysqlservercapabilities string			Server capabilities that the virtual server advertises to clients.
mysqlserverversion string			MySQL server version string that the virtual server advertises to clients. Minimum length = 1 Maximum length = 31
name string			Name for the virtual server. Must begin with an ASCII alphanumeric or underscore _ character, and must contain only ASCII alphanumeric, underscore, hash #, period ., space , colon :, at sign @, equal sign =, and hyphen - characters. Can be changed after the virtual server is created. Minimum length = 1
netmask string			IPv4 subnet mask to apply to the destination IP address or source IP address when the load balancing method is DESTINATIONIPHASH or SOURCEIPHASH. Minimum length = 1
netprofile string			Name of the network profile to associate with the virtual server. If you set this parameter, the virtual server uses only the IP addresses in the network profile as source IP addresses when initiating connections with servers. Minimum length = 1 Maximum length = 127
newservicerequest string			Number of requests, or percentage of the load on existing services, by which to increase the load on a new service at each interval in slow-start mode. A non-zero value indicates that slow-start is applicable. A zero value indicates that the global RR startup parameter is applied. Changing the value to zero will cause services currently in slow start to take the full traffic as determined by the LB method. Subsequently, any new services added will use the global RR factor.
newservicerequestincrementinterval string			Interval, in seconds, between successive increments in the load on a new service or a service whose state has just changed from DOWN to UP. A value of 0 (zero) specifies manual slow start. Minimum value = 0 Maximum value = 3600
newservicerequestunit string		Choices: PER_SECOND PERCENT	Units in which to increment load at each interval in slow-start mode.
nitro_pass string / required			The password with which to authenticate to the netscaler node.
nitro_protocol string		Choices: http ← https	Which protocol to use when accessing the nitro API objects.
nitro_timeout float		Default: 310	Time in seconds until a timeout error is thrown when establishing a new session with Netscaler
nitro_user string / required			The username with which to authenticate to the netscaler node.
nsip string / required			The ip address of the netscaler appliance where the nitro API calls will be made. The port can be specified with the colon (:). E.g. 192.168.1.1:555.
oracleserverversion string		Choices: 10G 11G	Oracle server version.
persistavpno string			Persist AVP number for Diameter Persistency. In case this AVP is not defined in Base RFC 3588 and it is nested inside a Grouped AVP, define a sequence of AVP numbers (max 3) in order of parent to child. So say persist AVP number X is nested inside AVP Y which is nested in Z, then define the list as Z Y X. Minimum value = 1
persistencebackup string		Choices: SOURCEIP NONE	Backup persistence type for the virtual server. Becomes operational if the primary persistence mechanism fails.
persistencetype string		Choices: SOURCEIP COOKIEINSERT SSLSESSION RULE URLPASSIVE CUSTOMSERVERID DESTIP SRCIPDESTIP CALLID RTSPSID DIAMETER FIXSESSION NONE	Type of persistence for the virtual server. Available settings function as follows: * SOURCEIP - Connections from the same client IP address belong to the same persistence session. * COOKIEINSERT - Connections that have the same HTTP Cookie, inserted by a Set-Cookie directive from a server, belong to the same persistence session. * SSLSESSION - Connections that have the same SSL Session ID belong to the same persistence session. * CUSTOMSERVERID - Connections with the same server ID form part of the same session. For this persistence type, set the Server ID (CustomServerID) parameter for each service and configure the Rule parameter to identify the server ID in a request. * RULE - All connections that match a user defined rule belong to the same persistence session. * URLPASSIVE - Requests that have the same server ID in the URL query belong to the same persistence session. The server ID is the hexadecimal representation of the IP address and port of the service to which the request must be forwarded. This persistence type requires a rule to identify the server ID in the request. * DESTIP - Connections to the same destination IP address belong to the same persistence session. * SRCIPDESTIP - Connections that have the same source IP address and destination IP address belong to the same persistence session. * CALLID - Connections that have the same CALL-ID SIP header belong to the same persistence session. * RTSPSID - Connections that have the same RTSP Session ID belong to the same persistence session. * FIXSESSION - Connections that have the same SenderCompID and TargetCompID values belong to the same persistence session.
persistmask string			Persistence mask for IP based persistence types, for IPv4 virtual servers. Minimum length = 1
port string			Port number for the virtual server. Range 1 - 65535 * in CLI is represented as 65535 in NITRO API
processlocal string		Choices: enabled disabled	By turning on this option packets destined to a vserver in a cluster will not under go any steering. Turn this option for single packet request response mode or when the upstream device is performing a proper RSS for connection based distribution.
push string		Choices: enabled disabled	Process traffic with the push virtual server that is bound to this load balancing virtual server.
pushlabel string			Expression for extracting a label from the server's response. Can be either an expression or the name of a named expression.
pushmulticlients boolean		Choices: no yes	Allow multiple Web 2.0 connections from the same client to connect to the virtual server and expect updates.
pushvserver string			Name of the load balancing virtual server, of type PUSH or SSL_PUSH, to which the server pushes updates received on the load balancing virtual server that you are configuring. Minimum length = 1
range string			Number of IP addresses that the appliance must generate and assign to the virtual server. The virtual server then functions as a network virtual server, accepting traffic on any of the generated IP addresses. The IP addresses are generated automatically, as follows: * For a range of n, the last octet of the address specified by the IP Address parameter increments n-1 times. * If the last octet exceeds 255, it rolls over to 0 and the third octet increments by 1. Note: The Range parameter assigns multiple IP addresses to one virtual server. To generate an array of virtual servers, each of which owns only one IP address, use brackets in the IP Address and Name parameters to specify the range. For example: add lb vserver my_vserver[1-3] HTTP 192.0.2.[1-3] 80. Minimum value = 1 Maximum value = 254
recursionavailable boolean		Choices: no yes	When set to YES, this option causes the DNS replies from this vserver to have the RA bit turned on. Typically one would set this option to YES, when the vserver is load balancing a set of DNS servers thatsupport recursive queries.
redirectportrewrite string		Choices: enabled disabled	Rewrite the port and change the protocol to ensure successful HTTP redirects from services.
redirurl string			URL to which to redirect traffic if the virtual server becomes unavailable. WARNING! Make sure that the domain in the URL does not match the domain specified for a content switching policy. If it does, requests are continuously redirected to the unavailable virtual server. Minimum length = 1
resrule string			Default syntax expression specifying which part of a server's response to use for creating rule based persistence sessions (persistence type RULE). Can be either an expression or the name of a named expression. Example: HTTP.RES.HEADER("setcookie".VALUE(0).TYPECAST_NVLIST_T("=",";").VALUE("server1")).
rhistate string		Choices: PASSIVE ACTIVE	Route Health Injection (RHI) functionality of the NetSaler appliance for advertising the route of the VIP address associated with the virtual server. When Vserver RHI Level (RHI) parameter is set to VSVR_CNTRLD, the following are different RHI behaviors for the VIP address on the basis of RHIstate (RHI STATE) settings on the virtual servers associated with the VIP address: * If you set rhistate to PASSIVE on all virtual servers, the NetScaler ADC always advertises the route for the VIP address. * If you set rhistate to ACTIVE on all virtual servers, the NetScaler ADC advertises the route for the VIP address if at least one of the associated virtual servers is in UP state. * If you set rhistate to ACTIVE on some and PASSIVE on others, the NetScaler ADC advertises the route for the VIP address if at least one of the associated virtual servers, whose rhistate set to ACTIVE, is in UP state.
rtspnat boolean		Choices: no yes	Use network address translation (NAT) for RTSP data connections.
save_config boolean		Choices: no yes ←	If yes the module will save the configuration on the netscaler node if it makes any changes. The module will not save the configuration on the netscaler node if it made no changes.
servicebindings string			List of services along with the weights that are load balanced. The following suboptions are available.
	servicename string		Service to bind to the virtual server. Minimum length = 1
	weight string		Weight to assign to the specified service. Minimum value = 1 Maximum value = 100
servicegroupbindings string			List of service groups along with the weights that are load balanced. The following suboptions are available.
	servicegroupname string		The service group name bound to the selected load balancing virtual server.
	weight string		Integer specifying the weight of the service. A larger number specifies a greater weight. Defines the capacity of the service relative to the other services in the load balancing configuration. Determines the priority given to the service in load balancing decisions. Minimum value = 1 Maximum value = 100
servicetype string		Choices: HTTP FTP TCP UDP SSL SSL_BRIDGE SSL_TCP DTLS NNTP DNS DHCPRA ANY SIP_UDP SIP_TCP SIP_SSL DNS_TCP RTSP PUSH SSL_PUSH RADIUS RDP MYSQL MSSQL DIAMETER SSL_DIAMETER TFTP ORACLE SMPP SYSLOGTCP SYSLOGUDP FIX SSL_FIX	Protocol used by the service (also called the service type).
sessionless string		Choices: enabled disabled	Perform load balancing on a per-packet basis, without establishing sessions. Recommended for load balancing of intrusion detection system (IDS) servers and scenarios involving direct server return (DSR), where session information is unnecessary.
skippersistency string		Choices: Bypass ReLb None	This argument decides the behavior incase the service which is selected from an existing persistence session has reached threshold.
sobackupaction string		Choices: DROP ACCEPT REDIRECT	Action to be performed if spillover is to take effect, but no backup chain to spillover is usable or exists.
somethod string		Choices: CONNECTION DYNAMICCONNECTION BANDWIDTH HEALTH NONE	Type of threshold that, when exceeded, triggers spillover. Available settings function as follows: * CONNECTION - Spillover occurs when the number of client connections exceeds the threshold. * DYNAMICCONNECTION - Spillover occurs when the number of client connections at the virtual server exceeds the sum of the maximum client (Max Clients) settings for bound services. Do not specify a spillover threshold for this setting, because the threshold is implied by the Max Clients settings of bound services. * BANDWIDTH - Spillover occurs when the bandwidth consumed by the virtual server's incoming and outgoing traffic exceeds the threshold. * HEALTH - Spillover occurs when the percentage of weights of the services that are UP drops below the threshold. For example, if services svc1, svc2, and svc3 are bound to a virtual server, with weights 1, 2, and 3, and the spillover threshold is 50%, spillover occurs if svc1 and svc3 or svc2 and svc3 transition to DOWN. * NONE - Spillover does not occur.
sopersistence string		Choices: enabled disabled	If spillover occurs, maintain source IP address based persistence for both primary and backup virtual servers.
sopersistencetimeout string			Timeout for spillover persistence, in minutes. Minimum value = 2 Maximum value = 1440
sothreshold string			Threshold at which spillover occurs. Specify an integer for the CONNECTION spillover method, a bandwidth value in kilobits per second for the BANDWIDTH method (do not enter the units), or a percentage for the HEALTH method (do not enter the percentage symbol). Minimum value = 1 Maximum value = 4294967287
ssl_certkey string			The name of the ssl certificate that is bound to this service. The ssl certificate must already exist. Creating the certificate can be done with the community.network.netscaler_ssl_certkey module. This option is only applicable only when servicetype is SSL.
state string		Choices: absent present ←	The state of the resource being configured by the module on the netscaler node. When present the resource will be created if needed and configured according to the module's parameters. When absent the resource will be deleted from the netscaler node.
tcpprofilename string			Name of the TCP profile whose settings are to be applied to the virtual server. Minimum length = 1 Maximum length = 127
td string			Integer value that uniquely identifies the traffic domain in which you want to configure the entity. If you do not specify an ID, the entity becomes part of the default traffic domain, which has an ID of 0. Minimum value = 0 Maximum value = 4094
timeout string			Time period for which a persistence session is in effect. Minimum value = 0 Maximum value = 1440
tosid string			TOS ID of the virtual server. Applicable only when the load balancing redirection mode is set to TOS. Minimum value = 1 Maximum value = 63
v6netmasklen string			Number of bits to consider in an IPv6 destination or source IP address, for creating the hash that is required by the DESTINATIONIPHASH and SOURCEIPHASH load balancing methods. Minimum value = 1 Maximum value = 128
v6persistmasklen string			Persistence mask for IP based persistence types, for IPv6 virtual servers. Minimum value = 1 Maximum value = 128
validate_certs boolean		Choices: no yes ←	If no, SSL certificates will not be validated. This should only be used on personally controlled sites using self-signed certificates.
vipheader string			Name for the inserted header. The default name is vip-header. Minimum length = 1

Notes

Note

• For more information on using Ansible to manage Citrix NetScaler Network devices see https://www.ansible.com/ansible-netscaler.

Examples

# Netscaler services service-http-1, service-http-2 must have been already created with the netscaler_service module

- name: Create a load balancing vserver bound to services
  delegate_to: localhost
  community.network.netscaler_lb_vserver:
    nsip: 172.18.0.2
    nitro_user: nsroot
    nitro_pass: nsroot
    validate_certs: no

    state: present

    name: lb_vserver_1
    servicetype: HTTP
    timeout: 12
    ipv46: 6.93.3.3
    port: 80
    servicebindings:
        - servicename: service-http-1
          weight: 80
        - servicename: service-http-2
          weight: 20

# Service group service-group-1 must have been already created with the netscaler_servicegroup module

- name: Create load balancing vserver bound to servicegroup
  delegate_to: localhost
  community.network.netscaler_lb_vserver:
    nsip: 172.18.0.2
    nitro_user: nsroot
    nitro_pass: nsroot
    validate_certs: no
    state: present

    name: lb_vserver_2
    servicetype: HTTP
    ipv46: 6.92.2.2
    port: 80
    timeout: 10
    servicegroupbindings:
        - servicegroupname: service-group-1

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
diff dictionary	failure	List of differences between the actual configured object and the configuration specified in the module Sample: {'clttimeout': 'difference. ours: (float) 10.0 other: (float) 20.0'}
loglines list / elements=string	always	list of logged messages by the module Sample: ['message 1', 'message 2']
msg string	failure	Message detailing the failure reason Sample: Action does not exist

Authors

• George Nikolopoulos (@giorgos-nikolopoulos)