bigip_snmp_community – Manages SNMP communities on a BIG-IP.¶

New in version 2.6.

Synopsis
Requirements
Parameters
Notes
Examples
Return Values
Status

Synopsis ¶

Assists in managing SNMP communities on a BIG-IP. Different SNMP versions are supported by this module. Take note of the different parameters offered by this module, as different parameters work for different versions of SNMP. Typically this becomes an interest if you are mixing versions v2c and 3.

Requirements ¶

The below requirements are needed on the host that executes this module.

f5-sdk >= 3.0.16

Parameters ¶

Parameter		Choices/Defaults	Comments
access -		Choices: ro rw read-only read-write	Specifies the user's access level to the MIB. When creating a new community, if this parameter is not specified, the default is `ro`. When `ro`, specifies that the user can view the MIB, but cannot modify the MIB. When `rw`, specifies that the user can view and modify the MIB.
community -			Specifies the community string (password) for access to the MIB. This parameter is only relevant when `version` is `v1`, or `v2c`. If `version` is something else, this parameter is ignored.
ip_version -		Choices: 4 6	Specifies whether the record applies to IPv4 or IPv6 addresses. When creating a new community, if this value is not specified, the default of `4` will be used. This parameter is only relevant when `version` is `v1`, or `v2c`. If `version` is something else, this parameter is ignored.
name -			Name that identifies the SNMP community. When `version` is `v1` or `v2c`, this parameter is required. The name `public` is a reserved name on the BIG-IP. This module handles that name differently than others. Functionally, you should not see a difference however.
oid -			Specifies the object identifier (OID) for the record. When `version` is `v3`, this parameter is required. When `version` is either `v1` or `v2c`, if this value is specified, then `source` must not be set to `all`.
partition -		Default: "Common"	Device partition to manage resources on.
password - / required			The password for the user account used to connect to the BIG-IP. You may omit this option by setting the environment variable `F5_PASSWORD`. aliases: pass, pwd
port -			Specifies the port for the trap destination. This parameter is only relevant when `version` is `v1`, or `v2c`. If `version` is something else, this parameter is ignored.
provider - added in 2.5		Default: null	A dict object containing connection details.
	password - / required		The password for the user account used to connect to the BIG-IP. You may omit this option by setting the environment variable `F5_PASSWORD`. aliases: pass, pwd
	server - / required		The BIG-IP host. You may omit this option by setting the environment variable `F5_SERVER`.
	server_port -	Default: 443	The BIG-IP server port. You may omit this option by setting the environment variable `F5_SERVER_PORT`.
	ssh_keyfile -		Specifies the SSH keyfile to use to authenticate the connection to the remote device. This argument is only used for cli transports. You may omit this option by setting the environment variable `ANSIBLE_NET_SSH_KEYFILE`.
	timeout -	Default: 10	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
	transport - / required	Choices: rest cli ←	Configures the transport connection to use when connecting to the remote device.
	user - / required		The username to connect to the BIG-IP with. This user must have administrative privileges on the device. You may omit this option by setting the environment variable `F5_USER`.
	validate_certs boolean	Choices: no yes ←	If `no`, SSL certificates are not validated. Use this only on personally controlled sites using self-signed certificates. You may omit this option by setting the environment variable `F5_VALIDATE_CERTS`.
server - / required			The BIG-IP host. You may omit this option by setting the environment variable `F5_SERVER`.
server_port - added in 2.2		Default: 443	The BIG-IP server port. You may omit this option by setting the environment variable `F5_SERVER_PORT`.
snmp_auth_password -			Specifies the password for the user. When creating a new SNMP `v3` community, this parameter is required. This value must be at least 8 characters long.
snmp_auth_protocol -		Choices: md5 sha none	Specifies the authentication method for the user. When `md5`, specifies that the system uses the MD5 algorithm to authenticate the user. When `sha`, specifies that the secure hash algorithm (SHA) to authenticate the user. When `none`, specifies that user does not require authentication. When creating a new SNMP `v3` community, if this parameter is not specified, the default of `sha` will be used.
snmp_privacy_password -			Specifies the password for the user. When creating a new SNMP `v3` community, this parameter is required. This value must be at least 8 characters long.
snmp_privacy_protocol -		Choices: aes des none	Specifies the encryption protocol. When `aes`, specifies that the system encrypts the user information using AES (Advanced Encryption Standard). When `des`, specifies that the system encrypts the user information using DES (Data Encryption Standard). When `none`, specifies that the system does not encrypt the user information. When creating a new SNMP `v3` community, if this parameter is not specified, the default of `aes` will be used.
snmp_username -			Specifies the name of the user for whom you want to grant access to the SNMP v3 MIB. This parameter is only relevant when `version` is `v3`. If `version` is something else, this parameter is ignored. When creating a new SNMP `v3` community, this parameter is required. This parameter cannot be changed once it has been set.
source -			Specifies the source address for access to the MIB. This parameter can accept a value of `all`. If this parameter is not specified, the value `all` is used. This parameter is only relevant when `version` is `v1`, or `v2c`. If `version` is something else, this parameter is ignored. If `source` is set to `all`, then it is not possible to specify an `oid`. This will raise an error. This parameter should be provided when `state` is `absent`, so that the correct community is removed. To remove the `public` SNMP community that comes with a BIG-IP, this parameter should be set to `default`.
state -		Choices: present ← absent	When `present`, ensures that the address list and entries exists. When `absent`, ensures the address list is removed.
update_password -		Choices: always ← on_create	`always` will allow to update passwords if the user chooses to do so. `on_create` will only set the password for newly created resources.
user - / required			The username to connect to the BIG-IP with. This user must have administrative privileges on the device. You may omit this option by setting the environment variable `F5_USER`.
validate_certs boolean added in 2.0		Choices: no yes ←	If `no`, SSL certificates are not validated. Use this only on personally controlled sites using self-signed certificates. You may omit this option by setting the environment variable `F5_VALIDATE_CERTS`.
version -		Choices: v1 v2c ← v3	Specifies to which Simple Network Management Protocol (SNMP) version the trap destination applies.

Notes ¶

Note

For more information on using Ansible to manage F5 Networks devices see https://www.ansible.com/integrations/networks/f5.
Requires the f5-sdk Python package on the host. This is as easy as pip install f5-sdk.
Requires BIG-IP software version >= 12.
The F5 modules only manipulate the running configuration of the F5 product. To ensure that BIG-IP specific configuration persists to disk, be sure to include at least one task that uses the bigip_config module to save the running configuration. Refer to the module’s documentation for the correct usage of the module to save your running configuration.

Examples ¶

- name: Create an SMNP v2c read-only community
  bigip_snmp_community:
    name: foo
    version: v2c
    source: all
    oid: .1
    access: ro
    password: secret
    server: lb.mydomain.com
    state: present
    user: admin
  delegate_to: localhost

- name: Create an SMNP v3 read-write community
  bigip_snmp_community:
    name: foo
    version: v3
    snmp_username: foo
    snmp_auth_protocol: sha
    snmp_auth_password: secret
    snmp_privacy_protocol: aes
    snmp_privacy_password: secret
    oid: .1
    access: rw
    password: secret
    server: lb.mydomain.com
    state: present
    user: admin
  delegate_to: localhost

- name: Remove the default 'public' SNMP community
  bigip_snmp_community:
    name: public
    source: default
    password: secret
    server: lb.mydomain.com
    state: absent
    user: admin
  delegate_to: localhost

Return Values ¶

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
param1 boolean	changed	The new param1 value of the resource. Sample: True
param2 string	changed	The new param2 value of the resource. Sample: Foo is bar

Status ¶

This module is not guaranteed to have a backwards compatible interface. [preview]
This module is maintained by an Ansible Partner. [certified]

Authors¶

Tim Rupp (@caphrim007)

Hint

If you notice any issues in this documentation you can edit this document to improve it.

bigip_snmp_community – Manages SNMP communities on a BIG-IP.¶

Synopsis¶

Requirements¶

Parameters¶

Notes¶

Examples¶

Return Values¶

Status¶