iosxr_interface – Manage Interface on Cisco IOS XR network devices¶

New in version 2.4.

Synopsis
Requirements
Parameters
Notes
Examples
Return Values
Status

Synopsis ¶

This module provides declarative management of Interfaces on Cisco IOS XR network devices.

Requirements ¶

The below requirements are needed on the host that executes this module.

ncclient >= 0.5.3 when using netconf
lxml >= 4.1.1 when using netconf

Parameters ¶

Parameter		Choices/Defaults	Comments
active - added in 2.5		Choices: active ← preconfigure	Whether the interface is `active` or `preconfigured`. Preconfiguration allows you to configure modular services cards before they are inserted into the router. When the cards are inserted, they are instantly configured. Active cards are the ones already inserted.
aggregate -			List of Interface definitions. Include multiple interface configurations together, one each on a separate line
delay -		Default: 10	Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values `up`/`down`, tx_rate and rx_rate.
description -			Description of Interface being configured.
duplex -		Choices: full half	Configures the interface duplex mode. Default is auto-negotiation when not configured.
enabled boolean		Choices: no yes ←	Removes the shutdown configuration, which removes the forced administrative down on the interface, enabling it to move to an up or down state.
mtu -			Sets the MTU value for the interface. Range is between 64 and 65535'
name - / required			Name of the interface to configure in `type + path` format. e.g. `GigabitEthernet0/0/0/0`
provider -			Deprecated Starting with Ansible 2.5 we recommend using `connection: network_cli`. For more information please see the Network Guide. A dict object containing connection details.
	host - / required		Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
	password -		Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_PASSWORD` will be used instead.
	port -	Default: 22	Specifies the port to use when building the connection to the remote device.
	ssh_keyfile -		Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_SSH_KEYFILE` will be used instead.
	timeout -	Default: 10	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
	username -		Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_USERNAME` will be used instead.
rx_rate -			Receiver rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
speed -		Choices: 10 100 1000	Configure the speed for an interface. Default is auto-negotiation when not configured.
state -		Choices: present ← absent up down	State of the Interface configuration, `up` means present and operationally up and `down` means present and operationally `down`
tx_rate -			Transmit rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules

Notes ¶

Note

Tested against IOS XRv 6.1.2
Preconfiguration of physical interfaces is not supported with netconf transport.
For more information on using Ansible to manage network devices see the Ansible Network Guide
For more information on using Ansible to manage Cisco devices see the Cisco integration page.

Examples ¶

- name: configure interface
  iosxr_interface:
      name: GigabitEthernet0/0/0/2
      description: test-interface
      speed: 100
      duplex: half
      mtu: 512

- name: remove interface
  iosxr_interface:
    name: GigabitEthernet0/0/0/2
    state: absent

- name: make interface up
  iosxr_interface:
    name: GigabitEthernet0/0/0/2
    enabled: True

- name: make interface down
  iosxr_interface:
    name: GigabitEthernet0/0/0/2
    enabled: False

- name: Create interface using aggregate
  iosxr_interface:
    aggregate:
    - name: GigabitEthernet0/0/0/3
    - name: GigabitEthernet0/0/0/2
    speed: 100
    duplex: full
    mtu: 512
    state: present

- name: Create interface using aggregate along with additional params in aggregate
  iosxr_interface:
    aggregate:
    - { name: GigabitEthernet0/0/0/3, description: test-interface 3 }
    - { name: GigabitEthernet0/0/0/2, description: test-interface 2 }
    speed: 100
    duplex: full
    mtu: 512
    state: present

- name: Delete interface using aggregate
  iosxr_interface:
    aggregate:
    - name: GigabitEthernet0/0/0/3
    - name: GigabitEthernet0/0/0/2
    state: absent

- name: Check intent arguments
  iosxr_interface:
    name: GigabitEthernet0/0/0/5
    state: up
    delay: 20

- name: Config + intent
  iosxr_interface:
    name: GigabitEthernet0/0/0/5
    enabled: False
    state: down
    delay: 20

Return Values ¶

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
commands list	always (empty list when no commands to send)	The list of configuration mode commands sent to device with transport `cli` Sample: ['interface GigabitEthernet0/0/0/2', 'description test-interface', 'duplex half', 'mtu 512']
xml list added in 2.5	always (empty list when no xml rpc to send)	NetConf rpc xml sent to device with transport `netconf` Sample: ['<config xmlns:xc="urn:ietf:params:xml:ns:netconf:base:1.0"> <interface-configurations xmlns="http://cisco.com/ns/yang/Cisco-IOS-XR-ifmgr-cfg"> <interface-configuration xc:operation="merge"> <active>act</active> <interface-name>GigabitEthernet0/0/0/0</interface-name> <description>test-interface-0</description> <mtus><mtu> <owner>GigabitEthernet</owner> <mtu>512</mtu> </mtu></mtus> <ethernet xmlns="http://cisco.com/ns/yang/Cisco-IOS-XR-drivers-media-eth-cfg"> <speed>100</speed> <duplex>half</duplex> </ethernet> </interface-configuration> </interface-configurations></config>']

Status ¶

This module is not guaranteed to have a backwards compatible interface. [preview]
This module is maintained by the Ansible Network Team. [network]

Red Hat Support¶

More information about Red Hat’s support of this module is available from this Red Hat Knowledge Base article.

Authors¶

Ganesh Nalawade (@ganeshrn)
Kedar Kekan (@kedarX)

Hint

If you notice any issues in this documentation you can edit this document to improve it.

iosxr_interface – Manage Interface on Cisco IOS XR network devices¶

Synopsis¶

Requirements¶

Parameters¶

Notes¶

Examples¶

Return Values¶

Status¶