onyx_command – Run commands on remote devices running Mellanox ONYX

New in version 2.5.

Synopsis

  • Sends arbitrary commands to an Mellanox ONYX network device and returns the results read from the device. This module includes an argument that will cause the module to wait for a specific condition before returning or timing out if the condition is not met.

  • This module does not support running commands in configuration mode. Please use onyx_config to configure Mellanox ONYX devices.

Parameters

Parameter Choices/Defaults Comments
commands
- / required
List of commands to send to the remote Mellanox ONYX network device. The resulting output from the command is returned. If the wait_for argument is provided, the module is not returned until the condition is satisfied or the number of retries has expired.
interval
-
Default:
1
Configures the interval in seconds to wait between retries of the command. If the command does not pass the specified conditions, the interval indicates how long to wait before trying the command again.
match
-
    Choices:
  • any
  • all ←
The match argument is used in conjunction with the wait_for argument to specify the match policy. Valid values are all or any. If the value is set to all then all conditionals in the wait_for must be satisfied. If the value is set to any then only one of the values must be satisfied.
provider
dictionary
A dict object containing connection details.
auth_pass
string
Specifies the password to use if required to enter privileged mode on the remote device. If authorize is false, then this argument does nothing. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_AUTH_PASS will be used instead.
authorize
boolean
    Choices:
  • no ←
  • yes
Instructs the module to enter privileged mode on the remote device before sending any commands. If not specified, the device will attempt to execute all commands in non-privileged mode. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_AUTHORIZE will be used instead.
host
string / required
Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
password
string
Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_PASSWORD will be used instead.
port
integer
Default:
22
Specifies the port to use when building the connection to the remote device.
ssh_keyfile
path
Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_SSH_KEYFILE will be used instead.
timeout
integer
Default:
10
Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
username
string
Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_USERNAME will be used instead.
retries
-
Default:
10
Specifies the number of retries a command should by tried before it is considered failed. The command is run on the target device every retry and evaluated against the wait_for conditions.
wait_for
-
List of conditions to evaluate against the output of the command. The task will wait for each condition to be true before moving forward. If the conditional is not true within the configured number of retries, the task fails. See examples.

Notes

Note

  • Tested on ONYX 3.6.4000

Examples

tasks:
  - name: run show version on remote devices
    onyx_command:
      commands: show version

  - name: run show version and check to see if output contains MLNXOS
    onyx_command:
      commands: show version
      wait_for: result[0] contains MLNXOS

  - name: run multiple commands on remote nodes
    onyx_command:
      commands:
        - show version
        - show interfaces

  - name: run multiple commands and evaluate the output
    onyx_command:
      commands:
        - show version
        - show interfaces
      wait_for:
        - result[0] contains MLNXOS
        - result[1] contains mgmt1

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
failed_conditions
list
 failed
The list of conditionals that have failed

Sample:
['...', '...']
stdout
list
 always apart from low level errors (such as action plugin)
The set of responses from the commands

Sample:
['...', '...']
stdout_lines
list
 always apart from low level errors (such as action plugin)
The value of stdout split into a list

Sample:
[['...', '...'], ['...'], ['...']]


Status

Authors

  • Samer Deeb (@samerd)

Hint

If you notice any issues in this documentation you can edit this document to improve it.