iptables – Modify iptables rules

Synopsis

• iptables is used to set up, maintain, and inspect the tables of IP packet filter rules in the Linux kernel.

• This module does not handle the saving and/or loading of rules, but rather only manipulates the current rules that are present in memory. This is the same as the behaviour of the iptables and ip6tables command which this module uses internally.

Parameters

Parameter		Choices/Defaults	Comments
action string		Choices: append ← insert	Whether the rule should be appended at the bottom or inserted at the top. If the rule already exists the chain will not be modified.
chain string			Specify the iptables chain to modify. This could be a user-defined chain or one of the standard iptables chains, like INPUT, FORWARD, OUTPUT, PREROUTING, POSTROUTING, SECMARK or CONNSECMARK.
comment string			This specifies a comment that will be added to the rule.
ctstate list		Default: []	ctstate is a list of the connection states to match in the conntrack module. Possible states are INVALID, NEW, ESTABLISHED, RELATED, UNTRACKED, SNAT, DNAT
destination string			Destination specification. Address can be either a network name, a hostname, a network IP address (with /mask), or a plain IP address. Hostnames will be resolved once only, before the rule is submitted to the kernel. Please note that specifying any name to be resolved with a remote query such as DNS is a really bad idea. The mask can be either a network mask or a plain number, specifying the number of 1's at the left side of the network mask. Thus, a mask of 24 is equivalent to 255.255.255.0. A ! argument before the address specification inverts the sense of the address.
destination_port string			Destination port or port range specification. This can either be a service name or a port number. An inclusive range can also be specified, using the format first:last. If the first port is omitted, '0' is assumed; if the last is omitted, '65535' is assumed. If the first port is greater than the second one they will be swapped. This is only valid if the rule also specifies one of the following protocols: tcp, udp, dccp or sctp.
dst_range string added in 2.8			Specifies the destination IP range to match in the iprange module.
flush boolean		Choices: no yes	Flushes the specified table and chain of all rules. If no chain is specified then the entire table is purged. Ignores all other parameters.
fragment string			This means that the rule only refers to second and further fragments of fragmented packets. Since there is no way to tell the source or destination ports of such a packet (or ICMP type), such a packet will not match any rules which specify them. When the "!" argument precedes fragment argument, the rule will only match head fragments, or unfragmented packets.
gateway string added in 2.8			This specifies the IP address of host to send the cloned packets. This option is only valid when jump is set to TEE.
gid_owner string added in 2.9			Specifies the GID or group to use in match by owner rule.
goto string			This specifies that the processing should continue in a user specified chain. Unlike the jump argument return will not continue processing in this chain but instead in the chain that called us via jump.
icmp_type string			This allows specification of the ICMP type, which can be a numeric ICMP type, type/code pair, or one of the ICMP type names shown by the command 'iptables -p icmp -h'
in_interface string			Name of an interface via which a packet was received (only for packets entering the INPUT, FORWARD and PREROUTING chains). When the ! argument is used before the interface name, the sense is inverted. If the interface name ends in a +, then any interface which begins with this name will match. If this option is omitted, any interface name will match.
ip_version string		Choices: ipv4 ← ipv6	Which version of the IP protocol this rule should apply to.
jump string			This specifies the target of the rule; i.e., what to do if the packet matches it. The target can be a user-defined chain (other than the one this rule is in), one of the special builtin targets which decide the fate of the packet immediately, or an extension (see EXTENSIONS below). If this option is omitted in a rule (and the goto parameter is not used), then matching the rule will have no effect on the packet's fate, but the counters on the rule will be incremented.
limit string			Specifies the maximum average number of matches to allow per second. The number can specify units explicitly, using `/second', `/minute', `/hour' or `/day', or parts of them (so `5/second' is the same as `5/s').
limit_burst string			Specifies the maximum burst before the above limit kicks in.
log_level string added in 2.8		Choices: 0 1 2 3 4 5 6 7 emerg alert crit error warning notice info debug	Logging level according to the syslogd-defined priorities. The value can be strings or numbers from 1-8. This parameter is only applicable if jump is set to LOG.
log_prefix string added in 2.5			Specifies a log text for the rule. Only make sense with a LOG jump.
match list		Default: []	Specifies a match to use, that is, an extension module that tests for a specific property. The set of matches make up the condition under which a target is invoked. Matches are evaluated first to last if specified as an array and work in short-circuit fashion, i.e. if one extension yields false, evaluation will stop.
out_interface string			Name of an interface via which a packet is going to be sent (for packets entering the FORWARD, OUTPUT and POSTROUTING chains). When the ! argument is used before the interface name, the sense is inverted. If the interface name ends in a +, then any interface which begins with this name will match. If this option is omitted, any interface name will match.
policy string		Choices: ACCEPT DROP QUEUE RETURN	Set the policy for the chain to the given target. Only built-in chains can have policies. This parameter requires the chain parameter. Ignores all other parameters.
protocol string			The protocol of the rule or of the packet to check. The specified protocol can be one of tcp, udp, udplite, icmp, esp, ah, sctp or the special keyword all, or it can be a numeric value, representing one of these protocols or a different one. A protocol name from /etc/protocols is also allowed. A ! argument before the protocol inverts the test. The number zero is equivalent to all. all will match with all protocols and is taken as default when this option is omitted.
reject_with string			Specifies the error packet type to return while rejecting. It implies "jump: REJECT"
rule_num string added in 2.5			Insert the rule as the given rule number. This works only with action=insert.
set_counters string			This enables the administrator to initialize the packet and byte counters of a rule (during INSERT, APPEND, REPLACE operations).
set_dscp_mark string			This allows specifying a DSCP mark to be added to packets. It takes either an integer or hex value. Mutually exclusive with set_dscp_mark_class.
set_dscp_mark_class string			This allows specifying a predefined DiffServ class which will be translated to the corresponding DSCP mark. Mutually exclusive with set_dscp_mark.
source string			Source specification. Address can be either a network name, a hostname, a network IP address (with /mask), or a plain IP address. Hostnames will be resolved once only, before the rule is submitted to the kernel. Please note that specifying any name to be resolved with a remote query such as DNS is a really bad idea. The mask can be either a network mask or a plain number, specifying the number of 1's at the left side of the network mask. Thus, a mask of 24 is equivalent to 255.255.255.0. A ! argument before the address specification inverts the sense of the address.
source_port string			Source port or port range specification. This can either be a service name or a port number. An inclusive range can also be specified, using the format first:last. If the first port is omitted, 0 is assumed; if the last is omitted, 65535 is assumed. If the first port is greater than the second one they will be swapped.
src_range string added in 2.8			Specifies the source IP range to match in the iprange module.
state string		Choices: absent present ←	Whether the rule should be absent or present.
syn string added in 2.5		Choices: ignore ← match negate	This allows matching packets that have the SYN bit set and the ACK and RST bits unset. When negated, this matches all packets with the RST or the ACK bits set.
table string		Choices: filter ← nat mangle raw security	This option specifies the packet matching table which the command should operate on. If the kernel is configured with automatic module loading, an attempt will be made to load the appropriate module for that table if it is not already there.
tcp_flags dictionary added in 2.4		Default: {}	TCP flags specification. tcp_flags expects a dict with the two keys flags and flags_set.
	flags list		List of flags you want to examine.
	flags_set list		Flags to be set.
to_destination string			This specifies a destination address to use with DNAT. Without this, the destination address is never altered.
to_ports string			This specifies a destination port or range of ports to use, without this, the destination port is never altered. This is only valid if the rule also specifies one of the protocol tcp, udp, dccp or sctp.
to_source string			This specifies a source address to use with SNAT. Without this, the source address is never altered.
uid_owner string			Specifies the UID or username to use in match by owner rule. From Ansible 2.6 when the ! argument is prepended then the it inverts the rule to apply instead to all users except that one specified.

Notes

Note

• This module just deals with individual rules.If you need advanced chaining of rules the recommended way is to template the iptables restore file.

Examples

- name: Block specific IP
  iptables:
    chain: INPUT
    source: 8.8.8.8
    jump: DROP
  become: yes

- name: Forward port 80 to 8600
  iptables:
    table: nat
    chain: PREROUTING
    in_interface: eth0
    protocol: tcp
    match: tcp
    destination_port: 80
    jump: REDIRECT
    to_ports: 8600
    comment: Redirect web traffic to port 8600
  become: yes

- name: Allow related and established connections
  iptables:
    chain: INPUT
    ctstate: ESTABLISHED,RELATED
    jump: ACCEPT
  become: yes

- name: Allow new incoming SYN packets on TCP port 22 (SSH).
  iptables:
    chain: INPUT
    protocol: tcp
    destination_port: 22
    ctstate: NEW
    syn: match
    jump: ACCEPT
    comment: Accept new SSH connections.

- name: Match on IP ranges
  iptables:
    chain: FORWARD
    src_range: 192.168.1.100-192.168.1.199
    dst_range: 10.0.0.1-10.0.0.50
    jump: ACCEPT

- name: Tag all outbound tcp packets with DSCP mark 8
  iptables:
    chain: OUTPUT
    jump: DSCP
    table: mangle
    set_dscp_mark: 8
    protocol: tcp

- name: Tag all outbound tcp packets with DSCP DiffServ class CS1
  iptables:
    chain: OUTPUT
    jump: DSCP
    table: mangle
    set_dscp_mark_class: CS1
    protocol: tcp

- name: Insert a rule on line 5
  iptables:
    chain: INPUT
    protocol: tcp
    destination_port: 8080
    jump: ACCEPT
    action: insert
    rule_num: 5

- name: Set the policy for the INPUT chain to DROP
  iptables:
    chain: INPUT
    policy: DROP

- name: Reject tcp with tcp-reset
  iptables:
    chain: INPUT
    protocol: tcp
    reject_with: tcp-reset
    ip_version: ipv4

- name: Set tcp flags
  iptables:
    chain: OUTPUT
    jump: DROP
    protocol: tcp
    tcp_flags:
      flags: ALL
      flags_set:
        - ACK
        - RST
        - SYN
        - FIN

- name: iptables flush filter
  iptables:
    chain: "{{ item }}"
    flush: yes
  with_items:  [ 'INPUT', 'FORWARD', 'OUTPUT' ]

- name: iptables flush nat
  iptables:
    table: nat
    chain: '{{ item }}'
    flush: yes
  with_items: [ 'INPUT', 'OUTPUT', 'PREROUTING', 'POSTROUTING' ]

- name: Log packets arriving into an user-defined chain
  iptables:
    chain: LOGGING
    action: append
    state: present
    limit: 2/second
    limit_burst: 20
    log_prefix: "IPTABLES:INFO: "
    log_level: info

Status

• This module is not guaranteed to have a backwards compatible interface. [preview]

• This module is maintained by the Ansible Core Team. [core]

Red Hat Support

More information about Red Hat’s support of this module is available from this Red Hat Knowledge Base article.

Authors

• Linus Unnebäck (@LinusU) <linus@folkdatorn.se>

• Sébastien DA ROCHA (@sebastiendarocha)

Hint

If you notice any issues in this documentation, you can edit this document to improve it.