na_elementsw_network_interfaces – NetApp Element Software Configure Node Network Interfaces

New in version 2.7.

Synopsis

  • Configure Element SW Node Network Interfaces for Bond 1G and 10G IP address.

Requirements

The below requirements are needed on the host that executes this module.

  • The modules were developed with SolidFire 10.1

  • solidfire-sdk-python (1.1.0.92) or greater. Install using ‘pip install solidfire-sdk-python’

Parameters

Parameter Choices/Defaults Comments
bond_mode_10g
-
    Choices:
  • ActivePassive ←
  • ALB
  • LACP
Bond mode for 10GbE configuration.
bond_mode_1g
-
    Choices:
  • ActivePassive ←
  • ALB
  • LACP
Bond mode for 1GbE configuration.
dns_nameservers
-
List of addresses for domain name servers.
dns_search_domains
-
List of DNS search domains.
gateway_address_10g
- / required
Router network address to send packets out of the local network.
gateway_address_1g
- / required
Router network address to send packets out of the local network.
hostname
- / required
The hostname or IP address of the SolidFire cluster.
ip_address_10g
- / required
IP address for the 10G network.
ip_address_1g
- / required
IP address for the 1G network.
lacp_10g
-
    Choices:
  • Fast
  • Slow ←
Link Aggregation Control Protocol useful only if LACP is selected as the Bond Mode.
Slow - Packets are transmitted at 30 second intervals.
Fast - Packets are transmitted in 1 second intervals.
lacp_1g
-
    Choices:
  • Fast
  • Slow ←
Link Aggregation Control Protocol useful only if LACP is selected as the Bond Mode.
Slow - Packets are transmitted at 30 second intervals.
Fast - Packets are transmitted in 1 second intervals.
method
- / required
    Choices:
  • loopback
  • manual
  • dhcp
  • static
Type of Method used to configure the interface.
method depends on other settings such as the use of a static IP address, which will change the method to static.
loopback - Used to define the IPv4 loopback interface.
manual - Used to define interfaces for which no configuration is done by default.
dhcp - May be used to obtain an IP address via DHCP.
static - Used to define Ethernet interfaces with statically allocated IPv4 addresses.
mtu_10g
-
Default:
"1500"
Maximum Transmission Unit for 10GbE, Largest packet size that a network protocol can transmit.
Must be greater than or equal to 1500 bytes.
mtu_1g
-
Default:
"1500"
Maximum Transmission Unit for 1GbE, Largest packet size that a network protocol can transmit.
Must be greater than or equal to 1500 bytes.
password
- / required
Password for the specified user.

aliases: pass
subnet_10g
- / required
10GbE Subnet Mask.
subnet_1g
- / required
1GbE Subnet Mask.
username
- / required
Please ensure that the user has the adequate permissions. For more information, please read the official documentation https://mysupport.netapp.com/documentation/docweb/index.html?productID=62636&language=en-US.

aliases: user
virtual_network_tag
-
This is the primary network tag. All nodes in a cluster have the same VLAN tag.

Notes

Note

  • The modules prefixed with na\_elementsw are built to support the SolidFire storage platform.

Examples

- name: Set Node network interfaces configuration for Bond 1G and 10G properties
  tags:
  - elementsw_network_interfaces
  na_elementsw_network_interfaces:
    hostname: "{{ elementsw_hostname }}"
    username: "{{ elementsw_username }}"
    password: "{{ elementsw_password }}"
    method: static
    ip_address_1g: 10.226.109.68
    ip_address_10g: 10.226.201.72
    subnet_1g: 255.255.255.0
    subnet_10g: 255.255.255.0
    gateway_address_1g: 10.193.139.1
    gateway_address_10g: 10.193.140.1
    mtu_1g: 1500
    mtu_10g: 9000
    bond_mode_1g: ActivePassive
    bond_mode_10g: LACP
    lacp_10g: Fast

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
msg
string
success
Success message


Status

Authors

Hint

If you notice any issues in this documentation, you can edit this document to improve it.