community.network.aruba_command – Run commands on remote devices running Aruba Mobility Controller

Note

This plugin is part of the community.network collection (version 2.1.1).

To install it use: ansible-galaxy collection install community.network.

To use it in a playbook, specify: community.network.aruba_command.

Synopsis

• Sends arbitrary commands to an aruba node and returns the results read from the device. This module includes an argument that will cause the module to wait for a specific condition before returning or timing out if the condition is not met.

• This module does not support running commands in configuration mode. Please use community.network.aruba_config to configure Aruba devices.

Parameters

Parameter		Choices/Defaults	Comments
commands string / required			List of commands to send to the remote aruba device over the configured provider. The resulting output from the command is returned. If the wait_for argument is provided, the module is not returned until the condition is satisfied or the number of retries has expired.
interval string		Default: 1	Configures the interval in seconds to wait between retries of the command. If the command does not pass the specified conditions, the interval indicates how long to wait before trying the command again.
match string		Choices: any all ←	The match argument is used in conjunction with the wait_for argument to specify the match policy. Valid values are all or any. If the value is set to all then all conditionals in the wait_for must be satisfied. If the value is set to any then only one of the values must be satisfied.
provider string			A dict object containing connection details.
	host string / required		Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
	password string		Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_PASSWORD will be used instead.
	port integer	Default: 22	Specifies the port to use when building the connection to the remote. device.
	ssh_keyfile path		Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_SSH_KEYFILE will be used instead.
	timeout integer	Default: 10	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
	username string		Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_USERNAME will be used instead.
retries string		Default: 10	Specifies the number of retries a command should by tried before it is considered failed. The command is run on the target device every retry and evaluated against the wait_for conditions.
wait_for string			List of conditions to evaluate against the output of the command. The task will wait for each condition to be true before moving forward. If the conditional is not true within the configured number of retries, the task fails. See examples. aliases: waitfor

Examples

tasks:
  - name: Run show version on remote devices
    community.network.aruba_command:
      commands: show version

  - name: Run show version and check to see if output contains Aruba
    community.network.aruba_command:
      commands: show version
      wait_for: result[0] contains Aruba

  - name: Run multiple commands on remote nodes
    community.network.aruba_command:
      commands:
        - show version
        - show interfaces

  - name: Run multiple commands and evaluate the output
    community.network.aruba_command:
      commands:
        - show version
        - show interfaces
      wait_for:
        - result[0] contains Aruba
        - result[1] contains Loopback0

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
failed_conditions list / elements=string	failed	The list of conditionals that have failed Sample: ['...', '...']
stdout list / elements=string	always	The set of responses from the commands Sample: ['...', '...']
stdout_lines list / elements=string	always	The value of stdout split into a list Sample: [['...', '...'], ['...'], ['...']]

Authors

• James Mighion (@jmighion)