community.network.ce_ospf – Manages configuration of an OSPF instance on HUAWEI CloudEngine switches.

Note

This plugin is part of the community.network collection (version 2.1.1).

To install it use: ansible-galaxy collection install community.network.

To use it in a playbook, specify: community.network.ce_ospf.

Synopsis

• Manages configuration of an OSPF instance on HUAWEI CloudEngine switches.

Parameters

Parameter	Choices/Defaults	Comments
addr string		Specifies the address of the network segment where the interface resides. The value is in dotted decimal notation.
area string		Specifies the area ID. The area with the area-id being 0 is a backbone area. Valid values are a string, formatted as an IP address (i.e. "0.0.0.0") or as an integer between 1 and 4294967295.
auth_key_id string		Authentication key id when auth_mode is 'hmac-sha256', 'md5' or 'hmac-md5. Valid value is an integer is in the range from 1 to 255.
auth_mode string	Choices: none hmac-sha256 md5 hmac-md5 simple	Specifies the authentication type.
auth_text_md5 string		Specifies a password for MD5, HMAC-MD5, or HMAC-SHA256 authentication. The value is a string of 1 to 255 case-sensitive characters, spaces not supported.
auth_text_simple string		Specifies a password for simple authentication. The value is a string of 1 to 8 characters.
mask string		IP network wildcard bits in decimal format between 0 and 32.
max_load_balance string		The maximum number of paths for forward packets over multiple paths. Valid value is an integer in the range from 1 to 64.
nexthop_addr string		IPv4 address for configure next-hop address's weight. Valid values are a string, formatted as an IP address.
nexthop_weight string		Indicates the weight of the next hop. The smaller the value is, the higher the preference of the route is. It is an integer that ranges from 1 to 254.
process_id string / required		Specifies a process ID. The value is an integer ranging from 1 to 4294967295.
state string	Choices: present ← absent	Determines whether the config should be present or not on the device.

Notes

Note

• This module requires the netconf system service be enabled on the remote device being managed.

• Recommended connection is netconf.

• This module also works with local connections for legacy playbooks.

Examples

- name: Ospf module test
  hosts: cloudengine
  connection: local
  gather_facts: no
  vars:
    cli:
      host: "{{ inventory_hostname }}"
      port: "{{ ansible_ssh_port }}"
      username: "{{ username }}"
      password: "{{ password }}"
      transport: cli

  tasks:

  - name: Configure ospf
    community.network.ce_ospf:
      process_id: 1
      area: 100
      state: present
      provider: "{{ cli }}"

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Returned	Description
changed boolean	always	check to see if a change was made on the device Sample: True
end_state dictionary	verbose mode	k/v pairs of configuration after module execution Sample: {'areas': [{'areaId': '0.0.0.100', 'areaType': 'Normal'}], 'max_load_balance': '32', 'nexthops': [], 'process_id': '1'}
existing dictionary	verbose mode	k/v pairs of existing configuration Sample: {'areas': [], 'max_load_balance': '32', 'nexthops': [], 'process_id': '1'}
proposed dictionary	verbose mode	k/v pairs of parameters passed into module Sample: {'area': '100', 'process_id': '1'}
updates list / elements=string	always	commands sent to the device Sample: ['ospf 1', 'area 0.0.0.100']

Authors

• QijunPan (@QijunPan)