community.network.cnos_interface – Manage Interface on Lenovo CNOS network devices

Note

This plugin is part of the community.network collection (version 2.1.1).

To install it use: ansible-galaxy collection install community.network.

To use it in a playbook, specify: community.network.cnos_interface.

Synopsis

  • This module provides declarative management of Interfaces on Lenovo CNOS network devices.

Parameters

Parameter Choices/Defaults Comments
aggregate
string
List of Interfaces definitions.
delay
string
Default:
20
Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values up/down, tx_rate and rx_rate
description
string
Description of Interface.
duplex
string
    Choices:
  • full
  • half
  • auto ←
Interface link status
enabled
boolean
    Choices:
  • no
  • yes ←
Interface link status.
mtu
string
Maximum size of transmit packet.
name
string / required
Name of the Interface.
neighbors
string
Check operational state of given interface name for LLDP neighbor.
The following suboptions are available.
host
string
LLDP neighbor host for given interface name.
port
string
LLDP neighbor port to which interface name is connected.
provider
string
Deprecated
Starting with Ansible 2.5 we recommend using connection: network_cli.
For more information please see the CNOS Platform Options guide.

A dict object containing connection details.
auth_pass
string
Specifies the password to use if required to enter privileged mode on the remote device. If authorize is false, then this argument does nothing. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_AUTH_PASS will be used instead.
authorize
boolean
    Choices:
  • no ←
  • yes
Instructs the module to enter privileged mode on the remote device before sending any commands. If not specified, the device will attempt to execute all commands in non-privileged mode. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_AUTHORIZE will be used instead.
host
string / required
Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
password
string
Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_PASSWORD will be used instead.
port
string
Default:
22
Specifies the port to use when building the connection to the remote device.
ssh_keyfile
string
Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_SSH_KEYFILE will be used instead.
timeout
string
Default:
10
Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
username
string
Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable ANSIBLE_NET_USERNAME will be used instead.
rx_rate
string
Receiver rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see Conditionals in Networking Modules
speed
string
Interface link speed.
state
string
    Choices:
  • present ←
  • absent
  • up
  • down
State of the Interface configuration, up means present and operationally up and down means present and operationally down
tx_rate
string
Transmit rate in bits per second (bps).
This is state check parameter only.
Supports conditionals, see Conditionals in Networking Modules

Notes

Note

  • Tested against CNOS 10.8.1

Examples

- name: Configure interface
  community.network.cnos_interface:
      name: Ethernet1/33
      description: test-interface
      speed: 100
      duplex: half
      mtu: 999

- name: Remove interface
  community.network.cnos_interface:
    name: loopback3
    state: absent

- name: Make interface up
  community.network.cnos_interface:
    name: Ethernet1/33
    enabled: True

- name: Make interface down
  community.network.cnos_interface:
    name: Ethernet1/33
    enabled: False

- name: Check intent arguments
  community.network.cnos_interface:
    name: Ethernet1/33
    state: up
    tx_rate: ge(0)
    rx_rate: le(0)

- name: Check neighbors intent arguments
  community.network.cnos_interface:
    name: Ethernet1/33
    neighbors:
    - port: eth0
      host: netdev

- name: Config + intent
  community.network.cnos_interface:
    name: Ethernet1/33
    enabled: False
    state: down

- name: Add interface using aggregate
  community.network.cnos_interface:
    aggregate:
    - { name: Ethernet1/33, mtu: 256, description: test-interface-1 }
    - { name: Ethernet1/44, mtu: 516, description: test-interface-2 }
    duplex: full
    speed: 100
    state: present

- name: Delete interface using aggregate
  community.network.cnos_interface:
    aggregate:
    - name: loopback3
    - name: loopback6
    state: absent

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
commands
list / elements=string
always, except for the platforms that use Netconf transport to manage the device.
The list of configuration mode commands to send to the device.

Sample:
['interface Ethernet1/33', 'description test-interface', 'duplex half', 'mtu 512']


Authors

  • Anil Kumar Muraleedharan(@amuraleedhar)