netapp_eseries.santricity.na_santricity_iscsi_interface – NetApp E-Series manage iSCSI interface configuration

Note

This plugin is part of the netapp_eseries.santricity collection (version 1.2.7).

To install it use: ansible-galaxy collection install netapp_eseries.santricity.

To use it in a playbook, specify: netapp_eseries.santricity.na_santricity_iscsi_interface.

Synopsis

  • Configure settings of an E-Series iSCSI interface

Parameters

Parameter Choices/Defaults Comments
address
string
The IPv4 address to assign to the interface.
Should be specified in xx.xx.xx.xx form.
Mutually exclusive with config_method=dhcp
api_password
string / required
The password to authenticate with the SANtricity Web Services Proxy or Embedded Web Services API.
api_url
string / required
The url to the SANtricity Web Services Proxy or Embedded Web Services API.
Example https://prod-1.wahoo.acme.com:8443/devmgr/v2
api_username
string / required
The username to authenticate with the SANtricity Web Services Proxy or Embedded Web Services API.
config_method
string
    Choices:
  • dhcp ←
  • static
The configuration method type to use for this interface.
dhcp is mutually exclusive with address, subnet_mask, and gateway.
controller
string / required
    Choices:
  • A
  • B
The controller that owns the port you want to configure.
Controller names are presented alphabetically, with the first controller as A, the second as B, and so on.
Current hardware models have either 1 or 2 available controllers, but that is not a guaranteed hard limitation and could change in the future.
gateway
string
The IPv4 gateway address to utilize for the interface.
Should be specified in xx.xx.xx.xx form.
Mutually exclusive with config_method=dhcp
mtu
integer
Default:
1500
The maximum transmission units (MTU), in bytes.
This allows you to configure a larger value for the MTU, in order to enable jumbo frames (any value > 1500).
Generally, it is necessary to have your host, switches, and other components not only support jumbo frames, but also have it configured properly. Therefore, unless you know what you're doing, it's best to leave this at the default.

aliases: max_frame_size
port
integer / required
The controller iSCSI HIC port to modify.
You can determine this value by numbering the iSCSI ports left to right on the controller you wish to modify starting with one.
ssid
string
Default:
1
The ID of the array to manage. This value must be unique for each array.
state
string
    Choices:
  • enabled ←
  • disabled
When enabled, the provided configuration will be utilized.
When disabled, the IPv4 configuration will be cleared and IPv4 connectivity disabled.
subnet_mask
string
The subnet mask to utilize for the interface.
Should be specified in xx.xx.xx.xx form.
Mutually exclusive with config_method=dhcp
validate_certs
boolean
    Choices:
  • no
  • yes ←
Should https certificates be validated?

Notes

Note

  • Check mode is supported.

  • The interface settings are applied synchronously, but changes to the interface itself (receiving a new IP address via dhcp, etc), can take seconds or minutes longer to take effect.

  • This module will not be useful/usable on an E-Series system without any iSCSI interfaces.

  • This module requires a Web Services API version of >= 1.3.

  • The E-Series Ansible modules require either an instance of the Web Services Proxy (WSP), to be available to manage the storage-system, or an E-Series storage-system that supports the Embedded Web Services API.

  • Embedded Web Services is currently available on the E2800, E5700, EF570, and newer hardware models.

  • netapp_e_storage_system may be utilized for configuring the systems managed by a WSP instance.

Examples

- name: Configure the first port on the A controller with a static IPv4 address
  na_santricity_iscsi_interface:
    ssid: "1"
    api_url: "https://192.168.1.100:8443/devmgr/v2"
    api_username: "admin"
    api_password: "adminpass"
    validate_certs: true
    port: "1"
    controller: "A"
    config_method: static
    address: "192.168.1.100"
    subnet_mask: "255.255.255.0"
    gateway: "192.168.1.1"

- name: Disable ipv4 connectivity for the second port on the B controller
  na_santricity_iscsi_interface:
    ssid: "1"
    api_url: "https://192.168.1.100:8443/devmgr/v2"
    api_username: "admin"
    api_password: "adminpass"
    validate_certs: true
    port: "2"
    controller: "B"
    state: disabled

- name: Enable jumbo frames for the first 4 ports on controller A
  na_santricity_iscsi_interface:
    ssid: "1"
    api_url: "https://192.168.1.100:8443/devmgr/v2"
    api_username: "admin"
    api_password: "adminpass"
    validate_certs: true
    port: "{{ item }}"
    controller: "A"
    state: enabled
    mtu: 9000
    config_method: dhcp
  loop:
    - 1
    - 2
    - 3
    - 4

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
msg
string
on success
Success message

Sample:
The interface settings have been updated.


Authors

  • Michael Price (@lmprice)

  • Nathan Swartz (@ndswartz)