cisco.ios.ios_l3_interfaces – L3 interfaces resource module

Note

This plugin is part of the cisco.ios collection (version 2.6.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install cisco.ios.

To use it in a playbook, specify: cisco.ios.ios_l3_interfaces.

New in version 1.0.0: of cisco.ios

Synopsis

  • This module provides declarative management of Layer-3 interface on Cisco IOS devices.

Note

This module has a corresponding action plugin.

Parameters

Parameter

Comments

config

list / elements=dictionary

A dictionary of Layer-3 interface options

ipv4

list / elements=dictionary

IPv4 address to be set for the Layer-3 interface mentioned in name option. The address format is <ipv4 address>/<mask>, the mask is number in range 0-32 eg. 192.168.0.1/24.

address

string

Configures the IPv4 address for Interface.

dhcp

dictionary

IP Address negotiated via DHCP.

client_id

string

Specify client-id to use.

enable

boolean

Enable dhcp.

Choices:

  • no

  • yes

hostname

string

Specify value for hostname option.

dhcp_client

string

Configures and specifies client-id to use over DHCP ip. Note, This option shall work only when dhcp is configured as IP.

GigabitEthernet interface number

This option is DEPRECATED and is replaced with dhcp which accepts dict as input this attribute will be removed after 2023-08-01.

dhcp_hostname

string

Configures and specifies value for hostname option over DHCP ip. Note, This option shall work only when dhcp is configured as IP.

This option is DEPRECATED and is replaced with dhcp which accepts dict as input this attribute will be removed after 2023-08-01.

pool

string

IP Address auto-configured from a local DHCP pool.

secondary

boolean

Configures the IP address as a secondary address.

Choices:

  • no

  • yes

ipv6

list / elements=dictionary

IPv6 address to be set for the Layer-3 interface mentioned in name option.

The address format is <ipv6 address>/<mask>, the mask is number in range 0-128 eg. fd5d:12c9:2201:1::1/64

address

string

Configures the IPv6 address for Interface.

anycast

boolean

Configure as an anycast

Choices:

  • no

  • yes

autoconfig

dictionary

Obtain address using auto-configuration.

default

boolean

Insert default route.

Choices:

  • no

  • yes

enable

boolean

enable auto-configuration.

Choices:

  • no

  • yes

cga

boolean

Use CGA interface identifier

Choices:

  • no

  • yes

dhcp

dictionary

Obtain a ipv6 address using DHCP.

enable

boolean

Enable dhcp.

Choices:

  • no

  • yes

rapid_commit

boolean

Enable Rapid-Commit.

Choices:

  • no

  • yes

eui

boolean

Use eui-64 interface identifier

Choices:

  • no

  • yes

boolean

Use link-local address

Choices:

  • no

  • yes

segment_routing

dictionary

Segment Routing submode

default

boolean

Set a command to its defaults.

Choices:

  • no

  • yes

enable

boolean

Enable segmented routing.

Choices:

  • no

  • yes

ipv6_sr

boolean

Set ipv6_sr.

Choices:

  • no

  • yes

name

string / required

Full name of the interface excluding any logical unit number, i.e. GigabitEthernet0/1.

running_config

string

This option is used only with state parsed.

The value of this option should be the output received from the IOS device by executing the command show running-config | section ^interface.

The state parsed reads the configuration from running_config option and transforms it into Ansible structured data as per the resource module’s argspec and the value is then returned in the parsed key within the result.

state

string

The state the configuration should be left in

The states rendered, gathered and parsed does not perform any change on the device.

The state rendered will transform the configuration in config option to platform specific CLI commands which will be returned in the rendered key within the result. For state rendered active connection to remote host is not required.

The state gathered will fetch the running configuration from device and transform it into structured data in the format as per the resource module argspec and the value is returned in the gathered key within the result.

The state parsed reads the configuration from running_config option and transforms it into JSON format as per the resource module parameters and the value is returned in the parsed key within the result. The value of running_config option should be the same format as the output of command show running-config | section ^interface executed on device. For state parsed active connection to remote host is not required.

Choices:

  • merged ← (default)

  • replaced

  • overridden

  • deleted

  • rendered

  • gathered

  • parsed

Notes

Note

Examples

# Using state merged

# Before state:
# -------------

# router-ios#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  ip address 10.1.1.1 255.255.255.0
#  duplex auto
#  speed auto
# interface GigabitEthernet0/2
#  description This is test
#  no ip address
#  duplex auto
#  speed 1000
# interface GigabitEthernet0/3
#  description Configured by Ansible Network
#  no ip address
# interface GigabitEthernet0/3.100
#  encapsulation dot1Q 20

- name: Merge provided configuration with device configuration
  cisco.ios.ios_l3_interfaces:
    config:
    - name: GigabitEthernet0/1
      ipv4:
      - address: 192.168.0.1/24
        secondary: true
    - name: GigabitEthernet0/2
      ipv4:
      - address: 192.168.0.2/24
    - name: GigabitEthernet0/3
      ipv6:
      - address: fd5d:12c9:2201:1::1/64
    - name: GigabitEthernet0/3.100
      ipv4:
      - address: 192.168.0.3/24
    state: merged

# Commands Fired:
# ---------------

# "commands": [
#       "interface GigabitEthernet0/1",
#       "ip address 192.168.0.1 255.255.255.0 secondary",
#       "interface GigabitEthernet0/2",
#       "ip address 192.168.0.2 255.255.255.0",
#       "interface GigabitEthernet0/3",
#       "ipv6 address fd5d:12c9:2201:1::1/64",
#       "GigabitEthernet0/3.100",
#       "ip address 192.168.0.3 255.255.255.0",
#     ],

# After state:
# ------------

# router-ios#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  ip address 10.1.1.1 255.255.255.0
#  ip address 192.168.0.1 255.255.255.0 secondary
#  duplex auto
#  speed auto
# interface GigabitEthernet0/2
#  description This is test
#  ip address 192.168.0.2 255.255.255.0
#  duplex auto
#  speed 1000
# interface GigabitEthernet0/3
#  description Configured by Ansible Network
#  ipv6 address FD5D:12C9:2201:1::1/64
# interface GigabitEthernet0/3.100
#  encapsulation dot1Q 20
#  ip address 192.168.0.3 255.255.255.0

# Using state replaced

# Before state:
# -------------

# router-ios#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  ip address 10.1.1.1 255.255.255.0
#  duplex auto
#  speed auto
# interface GigabitEthernet0/2
#  description This is test
#  no ip address
#  duplex auto
#  speed 1000
# interface GigabitEthernet0/3
#  description Configured by Ansible Network
#  ip address 192.168.2.0 255.255.255.0
# interface GigabitEthernet0/3.100
#  encapsulation dot1Q 20
#  ip address 192.168.0.2 255.255.255.0

- name: Replaces device configuration of listed interfaces with provided configuration
  cisco.ios.ios_l3_interfaces:
    config:
    - name: GigabitEthernet0/2
      ipv4:
      - address: 192.168.2.0/24
    - name: GigabitEthernet0/3
      ipv4:
      - dhcp:
          client_id: GigabitEthernet0/2
          hostname: test.com
    - name: GigabitEthernet0/3.100
      ipv4:
      - address: 192.168.0.3/24
        secondary: true
    state: replaced

# Commands Fired:
# ---------------

# "commands": [
#       "interface GigabitEthernet0/1",
#       "ip address 192.168.0.1 255.255.255.0 secondary",
#       "interface GigabitEthernet0/2",
#       "ip address 192.168.0.2 255.255.255.0",
#       "interface GigabitEthernet0/3",
#       "no ip address 192.168.2.0 255.255.255.0",
#       "ip address dhcp client-id GigabitEthernet0/2 hostname test.com",
#       "GigabitEthernet0/3.100",
#       "no ip address 192.168.0.2 255.255.255.0",
#       "ip address 192.168.0.3 255.255.255.0 secondary",
#     ],

# After state:
# ------------

# router-ios#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  ip address 10.1.1.1 255.255.255.0
#  duplex auto
#  speed auto
# interface GigabitEthernet0/2
#  description This is test
#  ip address 192.168.2.1 255.255.255.0
#  duplex auto
#  speed 1000
# interface GigabitEthernet0/3
#  description Configured by Ansible Network
#  ip address dhcp client-id GigabitEthernet0/2 hostname test.com
# interface GigabitEthernet0/3.100
#  encapsulation dot1Q 20
#  ip address 192.168.0.3 255.255.255.0 secondary

# Using state overridden

# Before state:
# -------------

# router-ios#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  ip address 10.1.1.1 255.255.255.0
#  duplex auto
#  speed auto
# interface GigabitEthernet0/2
#  description This is test
#  ip address 192.168.2.1 255.255.255.0
#  duplex auto
#  speed 1000
# interface GigabitEthernet0/3
#  description Configured by Ansible Network
#  ipv6 address FD5D:12C9:2201:1::1/64
# interface GigabitEthernet0/3.100
#  encapsulation dot1Q 20
#  ip address 192.168.0.2 255.255.255.0

- name: Override device configuration of all interfaces with provided configuration
  cisco.ios.ios_l3_interfaces:
    config:
    - name: GigabitEthernet0/2
      ipv4:
      - address: 192.168.0.1/24
    - name: GigabitEthernet0/3.100
      ipv6:
      - autoconfig: true
    state: overridden

# Commands Fired:
# ---------------

# "commands": [
#       "interface GigabitEthernet0/1",
#       "no ip address 10.1.1.1 255.255.255.0",
#       "interface GigabitEthernet0/2",
#       "no ip address 192.168.2.1 255.255.255.0",
#       "ip address 192.168.0.1 255.255.255.0",
#       "interface GigabitEthernet0/3",
#       "no ipv6 address FD5D:12C9:2201:1::1/64",
#       "GigabitEthernet0/3.100",
#       "no ip address 192.168.0.2 255.255.255.0",
#       "ipv6 address autoconfig",
#     ],

# After state:
# ------------

# router-ios#show running-config | section ^interface
# interface GigabitEthernet0/1
#  description Configured by Ansible
#  no ip address
#  duplex auto
#  speed auto
# interface GigabitEthernet0/2
#  description This is test
#  ip address 192.168.0.1 255.255.255.0
#  duplex auto
#  speed 1000
# interface GigabitEthernet0/3
#  description Configured by Ansible Network
# interface GigabitEthernet0/3.100
#  encapsulation dot1Q 20
#  ipv6 address autoconfig

# Using state Deleted

# Before state:
# -------------

# router-ios#show running-config | section ^interface
# interface GigabitEthernet0/1
#  ip address 192.0.2.10 255.255.255.0
#  shutdown
#  duplex auto
#  speed auto
# interface GigabitEthernet0/2
#  description Configured by Ansible Network
#  ip address 192.168.1.0 255.255.255.0
# interface GigabitEthernet0/3
#  description Configured by Ansible Network
#  ip address 192.168.0.1 255.255.255.0
#  shutdown
#  duplex full
#  speed 10
#  ipv6 address FD5D:12C9:2201:1::1/64
# interface GigabitEthernet0/3.100
#  encapsulation dot1Q 20
#  ip address 192.168.0.2 255.255.255.0

- name: "Delete attributes of given interfaces (NOTE: This won't delete the interfaces itself)"
  cisco.ios.ios_l3_interfaces:
    config:
    - name: GigabitEthernet0/2
    - name: GigabitEthernet0/3.100
    state: deleted

# "commands": [
#       "interface GigabitEthernet0/2",
#       "no ip address 192.168.1.0 255.255.255.0",
#       "GigabitEthernet0/3.100",
#       "no ip address 192.168.0.2 255.255.255.0",
#     ],

# After state:
# -------------

# router-ios#show running-config | section ^interface
# interface GigabitEthernet0/1
#  ip address 192.0.2.10 255.255.255.0
#  shutdown
#  duplex auto
#  speed auto
# interface GigabitEthernet0/2
#  description Configured by Ansible Network
#  no ip address
# interface GigabitEthernet0/3
#  description Configured by Ansible Network
#  ip address 192.168.0.1 255.255.255.0
#  shutdown
#  duplex full
#  speed 10
#  ipv6 address FD5D:12C9:2201:1::1/64
# interface GigabitEthernet0/3.100
#  encapsulation dot1Q 20

# Using state Deleted without any config passed
#"(NOTE: This will delete all of configured L3 resource module attributes from each configured interface)"

# Before state:
# -------------

# router-ios#show running-config | section ^interface
# interface GigabitEthernet0/1
#  ip address 192.0.2.10 255.255.255.0
#  shutdown
#  duplex auto
#  speed auto
# interface GigabitEthernet0/2
#  description Configured by Ansible Network
#  ip address 192.168.1.0 255.255.255.0
# interface GigabitEthernet0/3
#  description Configured by Ansible Network
#  ip address 192.168.0.1 255.255.255.0
#  shutdown
#  duplex full
#  speed 10
#  ipv6 address FD5D:12C9:2201:1::1/64
# interface GigabitEthernet0/3.100
#  encapsulation dot1Q 20
#  ip address 192.168.0.2 255.255.255.0

- name: "Delete L3 attributes of ALL interfaces together (NOTE: This won't delete the interface itself)"
  cisco.ios.ios_l3_interfaces:
    state: deleted

# "commands": [
#       "interface GigabitEthernet0/1",
#       "no ip address 192.0.2.10 255.255.255.0",
#       "interface GigabitEthernet0/2",
#       "no ip address 192.168.1.0 255.255.255.0",
#       "interface GigabitEthernet0/3",
#       "no ip address 192.168.0.1 255.255.255.0",
#       "no ipv6 address FD5D:12C9:2201:1::1/64",
#       "GigabitEthernet0/3.100",
#       "no ip address 192.168.0.2 255.255.255.0",
#     ],

# After state:
# -------------

# router-ios#show running-config | section ^interface
# interface GigabitEthernet0/1
#  no ip address
#  shutdown
#  duplex auto
#  speed auto
# interface GigabitEthernet0/2
#  description Configured by Ansible Network
#  no ip address
# interface GigabitEthernet0/3
#  description Configured by Ansible Network
#  shutdown
#  duplex full
#  speed 10
# interface GigabitEthernet0/3.100
#  encapsulation dot1Q 20

# Using state Gathered

# Before state:
# -------------

# router-ios#sh running-config | section ^interface
# interface GigabitEthernet0/1
#  ip address 203.0.113.27 255.255.255.0
# interface GigabitEthernet0/2
#  ip address 192.0.2.1 255.255.255.0 secondary
#  ip address 192.0.2.2 255.255.255.0
#  ipv6 address 2001:DB8:0:3::/64

- name: Gather listed l3 interfaces with provided configurations
  cisco.ios.ios_l3_interfaces:
    state: gathered

# Module Execution Result:
# ------------------------

# "gathered": [
#         {
#             "ipv4": [
#                 {
#                     "address": "203.0.113.27 255.255.255.0"
#                 }
#             ],
#             "name": "GigabitEthernet0/1"
#         },
#         {
#             "ipv4": [
#                 {
#                     "address": "192.0.2.1 255.255.255.0",
#                     "secondary": true
#                 },
#                 {
#                     "address": "192.0.2.2 255.255.255.0"
#                 }
#             ],
#             "ipv6": [
#                 {
#                     "address": "2001:db8:0:3::/64"
#                 }
#             ],
#             "name": "GigabitEthernet0/2"
#         }
#     ]

# After state:
# ------------

# router-ios#sh running-config | section ^interface
# interface GigabitEthernet0/1
#  ip address 203.0.113.27 255.255.255.0
# interface GigabitEthernet0/2
#  ip address 192.0.2.1 255.255.255.0 secondary
#  ip address 192.0.2.2 255.255.255.0
#  ipv6 address 2001:DB8:0:3::/64

# Using state Rendered

- name: Render the commands for provided configuration
  cisco.ios.ios_l3_interfaces:
    config:
    - name: GigabitEthernet0/1
      ipv4:
      - dhcp:
          client_id: GigabitEthernet0/0
          hostname: test.com
    - name: GigabitEthernet0/2
      ipv4:
      - address: 198.51.100.1/24
        secondary: true
      - address: 198.51.100.2/24
      ipv6:
      - address: 2001:db8:0:3::/64
    state: rendered

# Module Execution Result:
# ------------------------

# "rendered": [
#         "interface GigabitEthernet0/1",
#         "ip address dhcp client-id GigabitEthernet 0/0 hostname test.com",
#         "interface GigabitEthernet0/2",
#         "ip address 198.51.100.1 255.255.255.0 secondary",
#         "ip address 198.51.100.2 255.255.255.0",
#         "ipv6 address 2001:db8:0:3::/64"
#     ]

# Using state Parsed

# File: parsed.cfg
# ----------------
#
# interface GigabitEthernet0/1
#  ip address dhcp client-id GigabitEthernet 0/0 hostname test.com
# interface GigabitEthernet0/2
#  ip address 198.51.100.1 255.255.255.0
#  ip address 198.51.100.2 255.255.255.0 secondary
#  ipv6 address 2001:db8:0:3::/64

- name: Parse the commands for provided configuration
  cisco.ios.ios_l3_interfaces:
    running_config: "{{ lookup('file', 'parsed.cfg') }}"
    state: parsed

# Module Execution Result:
# ------------------------

# "parsed": [
#         {
#             "ipv4": [
#                 {
#                     "dhcp": {
#                         "client_id": GigabitEthernet0/0,
#                         "hostname": "test.com"
#                     }
#                 }
#             ],
#             "name": "GigabitEthernet0/1"
#         },
#         {
#             "ipv4": [
#                 {
#                     "address": "198.51.100.1/24",
#                     "secondary": true
#                 },
#                 {
#                     "address": "198.51.100.2/24"
#                 }
#             ],
#             "ipv6": [
#                 {
#                     "address": "2001:db8:0:3::/64"
#                 }
#             ],
#             "name": "GigabitEthernet0/2"
#         }
#     ]

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key

Description

after

dictionary

The resulting configuration after module execution.

Returned: when changed

Sample: “This output will always be in the same format as the module argspec.\n”

before

dictionary

The configuration prior to the module execution.

Returned: when state is merged, replaced, overridden, deleted or purged

Sample: “This output will always be in the same format as the module argspec.\n”

commands

list / elements=string

The set of commands pushed to the remote device.

Returned: when state is merged, replaced, overridden, deleted or purged

Sample: [“ip address 192.168.0.3 255.255.255.0”, “ipv6 address dhcp rapid-commit”, “ipv6 address fd5d:12c9:2201:1::1/64 anycast”]

gathered

list / elements=string

Facts about the network resource gathered from the remote device as structured data.

Returned: when state is gathered

Sample: “This output will always be in the same format as the module argspec.\n”

parsed

list / elements=string

The device native config provided in running_config option parsed into structured data as per module argspec.

Returned: when state is parsed

Sample: “This output will always be in the same format as the module argspec.\n”

rendered

list / elements=string

The provided configuration in the task rendered in device-native format (offline).

Returned: when state is rendered

Sample: [“ipv6 address FD5D:12C9:2201:1::1/64”, “ip address 192.168.0.3 255.255.255.0”, “ip address autoconfig”]

Authors

  • Sagar Paul (@KB-perByte)

  • Sumit Jaiswal (@justjais)