You are reading an unmaintained version of the Ansible documentation. Unmaintained Ansible versions can contain unfixed security vulnerabilities (CVE). Please upgrade to a maintained version. See the latest Ansible documentation.

cisco.nxos.nxos_ospfv2 – OSPFv2 resource module

Note

This plugin is part of the cisco.nxos collection (version 2.8.2).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install cisco.nxos.

To use it in a playbook, specify: cisco.nxos.nxos_ospfv2.

New in version 1.0.0: of cisco.nxos

Synopsis
Parameters
Notes
Examples
Return Values

Synopsis 

This module manages OSPFv2 configuration on devices running Cisco NX-OS.

Note

This module has a corresponding action plugin.

Parameters 

Parameter	Comments
config dictionary	A list of OSPF process configuration.
processes list / elements=dictionary	A list of OSPF instances’ configurations.
areas list / elements=dictionary	Configure properties of OSPF Areas.
area_id string / required	The Area ID in IP Address format.
authentication dictionary	Authentication settings for the Area.
message_digest boolean	Use message-digest authentication. Choices: no yes
set boolean	Set authentication for the area. Choices: no yes
default_cost integer	Specify the default cost for default summary LSA.
filter_list list / elements=dictionary	Filter prefixes between OSPF areas.
direction string / required	The direction to apply the route map. Choices: in out
route_map string / required	The Route-map name.
nssa dictionary	NSSA settings for the area.
default_information_originate boolean	Originate Type-7 default LSA into NSSA area. Choices: no yes
no_redistribution boolean	Do not send redistributed LSAs into NSSA area. Choices: no yes
no_summary boolean	Do not send summary LSAs into NSSA area. Choices: no yes
set boolean	Configure area as NSSA. Choices: no yes
translate dictionary	Translate LSA.
type7 dictionary	Translate from Type 7 to Type 5.
always boolean	Always translate LSAs Choices: no yes
never boolean	Never translate LSAs Choices: no yes
supress_fa boolean	Suppress forwarding address in translated LSAs. Choices: no yes
ranges list / elements=dictionary	Configure an address range for the area.
cost integer	Cost to use for the range.
not_advertise boolean	Suppress advertising the specified range. Choices: no yes
prefix string / required	IP in Prefix format (x.x.x.x/len)
stub dictionary	Settings for configuring the area as a stub.
no_summary boolean	Prevent ABR from sending summary LSAs into stub area. Choices: no yes
set boolean	Configure the area as a stub. Choices: no yes
auto_cost dictionary	Calculate OSPF cost according to bandwidth.
reference_bandwidth integer / required	Reference bandwidth used to assign OSPF cost.
unit string / required	Specify in which unit the reference bandwidth is specified. Choices: Gbps Mbps
bfd boolean	Enable BFD on all OSPF interfaces. Choices: no yes
default_information dictionary	Control distribution of default routes.
originate dictionary	Distribute a default route.
always boolean	Always advertise a default route. Choices: no yes
route_map string	Policy to control distribution of default routes
set boolean	Enable distribution of default route. Choices: no yes
default_metric integer	Specify default metric for redistributed routes.
distance integer	Configure the OSPF administrative distance.
flush_routes boolean	Flush routes on a non-graceful controlled restart. Choices: no yes
graceful_restart dictionary	Configure graceful restart.
grace_period integer	Configure maximum interval to restart gracefully.
helper_disable boolean	Enable/Disable helper mode. Choices: no yes
set boolean	Enable graceful-restart. Choices: no yes
isolate boolean	Isolate this router from OSPF perspective. Choices: no yes
log_adjacency_changes dictionary	Log changes in adjacency state.
detail boolean	Notify all state changes. Choices: no yes
log boolean	Enable/disable logging changes in adjacency state. Choices: no yes
max_lsa dictionary	Feature to limit the number of non-self-originated LSAs.
ignore_count integer	Set count on how many times adjacencies can be suppressed.
ignore_time integer	Set time during which all adjacencies are suppressed.
max_non_self_generated_lsa integer / required	Set the maximum number of non self-generated LSAs.
reset_time integer	Set number of minutes after which ignore-count is reset to zero.
threshold integer	Threshold value (%) at which to generate a warning message.
warning_only boolean	Log a warning message when limit is exceeded. Choices: no yes
max_metric dictionary	Maximize the cost metric.
router_lsa dictionary	Router LSA configuration.
external_lsa dictionary	External LSA configuration.
max_metric_value integer	Set max metric value for external LSAs.
set boolean	Set external-lsa attribute. Choices: no yes
include_stub boolean	Advertise Max metric for Stub links as well. Choices: no yes
on_startup dictionary	Effective only at startup.
set boolean	Set on-startup attribute. Choices: no yes
wait_for_bgp_asn integer	ASN of BGP to wait for.
wait_period integer	Wait period in seconds after startup.
set boolean	Set router-lsa attribute. Choices: no yes
summary_lsa dictionary	Summary LSAs configuration.
max_metric_value integer	Max metric value for summary LSAs.
set boolean	Set summary-lsa attribute. Choices: no yes
maximum_paths integer	Maximum paths per destination.
mpls dictionary	OSPF MPLS configuration settings.
traffic_eng dictionary	OSPF MPLS Traffic Engineering commands.
areas list / elements=dictionary	List of Area IDs.
area_id string	Area Id in ip address format.
multicast_intact boolean	MPLS TE multicast support. Choices: no yes
router_id string	Router ID associated with TE.
name_lookup boolean	Display OSPF router ids as DNS names. Choices: no yes
passive_interface dictionary	Suppress routing updates on the interface.
default boolean	Interfaces passive by default. Choices: no yes
process_id string / required	The OSPF process tag.
redistribute list / elements=dictionary	Redistribute information from another routing protocol.
id string	The identifier for the protocol specified.
protocol string / required	The name of the protocol. Choices: bgp direct eigrp isis lisp ospf rip static
route_map string / required	The route map policy to constrain redistribution.
rfc1583compatibility boolean	Configure 1583 compatibility for external path preferences. Choices: no yes
router_id string	Set OSPF process router-id.
shutdown boolean	Shutdown the OSPF protocol instance. Choices: no yes
summary_address list / elements=dictionary	Configure route summarization for redistribution.
not_advertise boolean	Suppress advertising the specified summary. Choices: no yes
prefix string / required	IP prefix in format x.x.x.x/ml.
tag integer	A 32-bit tag value.
table_map dictionary	Policy for filtering/modifying OSPF routes before sending them to RIB.
filter boolean	Block the OSPF routes from being sent to RIB. Choices: no yes
name string / required	The Route Map name.
timers dictionary	Configure timer related constants.
lsa_arrival integer	Mimimum interval between arrival of a LSA.
lsa_group_pacing integer	LSA group refresh/maxage interval.
throttle dictionary	Configure throttle related constants.
lsa dictionary	Set rate-limiting for LSA generation.
hold_interval integer	The hold interval.
max_interval integer	The max interval.
start_interval integer	The start interval.
spf dictionary	Set OSPF SPF timers.
initial_spf_delay integer	Initial SPF schedule delay in milliseconds.
max_wait_time integer	Maximum wait time between SPF calculations.
min_hold_time integer	Minimum hold time between SPF calculations.
vrfs list / elements=dictionary	Configure VRF specific OSPF settings.
areas list / elements=dictionary	Configure properties of OSPF Areas.
area_id string / required	The Area ID in IP Address format.
authentication dictionary	Authentication settings for the Area.
message_digest boolean	Use message-digest authentication. Choices: no yes
set boolean	Set authentication for the area. Choices: no yes
default_cost integer	Specify the default cost for default summary LSA.
filter_list list / elements=dictionary	Filter prefixes between OSPF areas.
direction string / required	The direction to apply the route map. Choices: in out
route_map string / required	The Route-map name.
nssa dictionary	NSSA settings for the area.
default_information_originate boolean	Originate Type-7 default LSA into NSSA area. Choices: no yes
no_redistribution boolean	Do not send redistributed LSAs into NSSA area. Choices: no yes
no_summary boolean	Do not send summary LSAs into NSSA area. Choices: no yes
set boolean	Configure area as NSSA. Choices: no yes
translate dictionary	Translate LSA.
type7 dictionary	Translate from Type 7 to Type 5.
always boolean	Always translate LSAs Choices: no yes
never boolean	Never translate LSAs Choices: no yes
supress_fa boolean	Suppress forwarding address in translated LSAs. Choices: no yes
ranges list / elements=dictionary	Configure an address range for the area.
cost integer	Cost to use for the range.
not_advertise boolean	Suppress advertising the specified range. Choices: no yes
prefix string / required	IP in Prefix format (x.x.x.x/len)
stub dictionary	Settings for configuring the area as a stub.
no_summary boolean	Prevent ABR from sending summary LSAs into stub area. Choices: no yes
set boolean	Configure the area as a stub. Choices: no yes
auto_cost dictionary	Calculate OSPF cost according to bandwidth.
reference_bandwidth integer / required	Reference bandwidth used to assign OSPF cost.
unit string / required	Specify in which unit the reference bandwidth is specified. Choices: Gbps Mbps
bfd boolean	Enable BFD on all OSPF interfaces. Choices: no yes
capability dictionary	OSPF capability settings.
vrf_lite dictionary	Enable VRF-lite capability settings.
evpn boolean	Ethernet VPN. Choices: no yes
set boolean	Enable VRF-lite support. Choices: no yes
default_information dictionary	Control distribution of default routes.
originate dictionary	Distribute a default route.
always boolean	Always advertise a default route. Choices: no yes
route_map string	Policy to control distribution of default routes
set boolean	Enable distribution of default route. Choices: no yes
default_metric integer	Specify default metric for redistributed routes.
distance integer	Configure the OSPF administrative distance.
down_bit_ignore boolean	Configure a PE router to ignore the DN bit for network summary, external and NSSA external LSA. Choices: no yes
graceful_restart dictionary	Configure graceful restart.
grace_period integer	Configure maximum interval to restart gracefully.
helper_disable boolean	Enable/Disable helper mode. Choices: no yes
set boolean	Enable graceful-restart. Choices: no yes
log_adjacency_changes dictionary	Log changes in adjacency state.
detail boolean	Notify all state changes. Choices: no yes
log boolean	Enable/disable logging changes in adjacency state. Choices: no yes
max_lsa dictionary	Feature to limit the number of non-self-originated LSAs.
ignore_count integer	Set count on how many times adjacencies can be suppressed.
ignore_time integer	Set time during which all adjacencies are suppressed.
max_non_self_generated_lsa integer / required	Set the maximum number of non self-generated LSAs.
reset_time integer	Set number of minutes after which ignore-count is reset to zero.
threshold integer	Threshold value (%) at which to generate a warning message.
warning_only boolean	Log a warning message when limit is exceeded. Choices: no yes
max_metric dictionary	Maximize the cost metric.
router_lsa dictionary	Router LSA configuration.
external_lsa dictionary	External LSA configuration.
max_metric_value integer	Set max metric value for external LSAs.
set boolean	Set external-lsa attribute. Choices: no yes
include_stub boolean	Advertise Max metric for Stub links as well. Choices: no yes
on_startup dictionary	Effective only at startup.
set boolean	Set on-startup attribute. Choices: no yes
wait_for_bgp_asn integer	ASN of BGP to wait for.
wait_period integer	Wait period in seconds after startup.
set boolean	Set router-lsa attribute. Choices: no yes
summary_lsa dictionary	Summary LSAs configuration.
max_metric_value integer	Max metric value for summary LSAs.
set boolean	Set summary-lsa attribute. Choices: no yes
maximum_paths integer	Maximum paths per destination.
name_lookup boolean	Display OSPF router ids as DNS names. Choices: no yes
passive_interface dictionary	Suppress routing updates on the interface.
default boolean	Interfaces passive by default. Choices: no yes
redistribute list / elements=dictionary	Redistribute information from another routing protocol.
id string	The identifier for the protocol specified.
protocol string / required	The name of the protocol. Choices: bgp direct eigrp isis lisp ospf rip static
route_map string / required	The route map policy to constrain redistribution.
rfc1583compatibility boolean	Configure 1583 compatibility for external path preferences. Choices: no yes
router_id string	Set OSPF process router-id.
shutdown boolean	Shutdown the OSPF protocol instance. Choices: no yes
summary_address list / elements=dictionary	Configure route summarization for redistribution.
not_advertise boolean	Suppress advertising the specified summary. Choices: no yes
prefix string / required	IP prefix in format x.x.x.x/ml.
tag integer	A 32-bit tag value.
table_map dictionary	Policy for filtering/modifying OSPF routes before sending them to RIB.
filter boolean	Block the OSPF routes from being sent to RIB. Choices: no yes
name string / required	The Route Map name.
timers dictionary	Configure timer related constants.
lsa_arrival integer	Mimimum interval between arrival of a LSA.
lsa_group_pacing integer	LSA group refresh/maxage interval.
throttle dictionary	Configure throttle related constants.
lsa dictionary	Set rate-limiting for LSA generation.
hold_interval integer	The hold interval.
max_interval integer	The max interval.
start_interval integer	The start interval.
spf dictionary	Set OSPF SPF timers.
initial_spf_delay integer	Initial SPF schedule delay in milliseconds.
max_wait_time integer	Maximum wait time between SPF calculations.
min_hold_time integer	Minimum hold time between SPF calculations.
vrf string / required	Name/Identifier of the VRF.
running_config string	This option is used only with state parsed. The value of this option should be the output received from the NX-OS device by executing the command *show running-config \| section “^router ospf .”*. The state parsed* reads the configuration from `running_config` option and transforms it into Ansible structured data as per the resource module’s argspec and the value is then returned in the parsed key within the result.
state string	The state the configuration should be left in. Choices: merged ← (default) replaced overridden deleted gathered parsed rendered

Notes 

Note

Tested against NX-OS 7.0(3)I5(1).
Unsupported for Cisco MDS
This module works with connection network_cli and httpapi.

Examples 

# Using merged

# Before state:
# -------------
# nxos-9k-rdo# sh running-config | section "^router ospf .*"
# nxos-9k-rdo#

- name: Merge the provided configuration with the existing running configuration
  cisco.nxos.nxos_ospfv2:
    config:
      processes:
      - process_id: 100
        router_id: 203.0.113.20
      - process_id: 102
        router_id: 198.51.100.1
        areas:
        - area_id: 0.0.0.100
          filter_list:
          - route_map: rmap_1
            direction: in
          - route_map: rmap_2
            direction: out
          ranges:
          - prefix: 198.51.100.64/27
            not_advertise: true
          - prefix: 198.51.100.96/27
            cost: 120
        - area_id: 0.0.0.101
          authentication:
            message_digest: true
        redistribute:
        - protocol: eigrp
          id: 120
          route_map: rmap_1
        - protocol: direct
          route_map: ospf102-direct-connect
        vrfs:
        - vrf: zone1
          router_id: 198.51.100.129
          redistribute:
          - protocol: static
            route_map: zone1-static-connect
          summary_address:
          - prefix: 198.51.100.128/27
            tag: 121
          - prefix: 198.51.100.160/27
          areas:
          - area_id: 0.0.0.102
            nssa:
              default_information_originate: true
              no_summary: true
          - area_id: 0.0.0.103
            nssa:
              no_summary: true
              translate:
                type7:
                  always: true
        - vrf: zone2
          auto_cost:
            reference_bandwidth: 45
            unit: Gbps
    state: merged

# Task output
# -------------
# before: {}
#
# commands:
#  - router ospf 102
#  - router-id 198.51.100.1
#  - redistribute eigrp 120 route-map rmap_1
#  - redistribute direct route-map ospf102-direct-connect
#  - area 0.0.0.100 filter-list route-map rmap_1 in
#  - area 0.0.0.100 filter-list route-map rmap_2 out
#  - area 0.0.0.100 range 198.51.100.64/27 not-advertise
#  - area 0.0.0.100 range 198.51.100.96/27 cost 120
#  - area 0.0.0.101 authentication message-digest
#  - vrf zone1
#  - router-id 198.51.100.129
#  - summary-address 198.51.100.128/27 tag 121
#  - summary-address 198.51.100.160/27
#  - redistribute static route-map zone1-static-connect
#  - area 0.0.0.102 nssa no-summary default-information-originate
#  - area 0.0.0.103 nssa no-summary
#  - area 0.0.0.103 nssa translate type7 always
#  - vrf zone2
#  - auto-cost reference-bandwidth 45 Gbps
#  - router ospf 100
#  - router-id 203.0.113.20
#
# after:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - areas:
#      - area_id: 0.0.0.100
#        filter_list:
#        - direction: out
#          route_map: rmap_2
#        - direction: in
#          route_map: rmap_1
#        ranges:
#        - not_advertise: true
#          prefix: 198.51.100.64/27
#        - cost: 120
#          prefix: 198.51.100.96/27
#      - area_id: 0.0.0.101
#        authentication:
#          message_digest: true
#      process_id: "102"
#      redistribute:
#      - protocol: direct
#        route_map: ospf102-direct-connect
#      - id: "120"
#        protocol: eigrp
#        route_map: rmap_1
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        redistribute:
#        - protocol: static
#          route_map: zone1-static-connect
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospf .*"
# router ospf 100
#   router-id 203.0.113.20
# router ospf 102
#   router-id 198.51.100.1
#   redistribute direct route-map ospf102-direct-connect
#   redistribute eigrp 120 route-map rmap_1
#   area 0.0.0.100 filter-list route-map rmap_2 out
#   area 0.0.0.100 filter-list route-map rmap_1 in
#   area 0.0.0.100 range 198.51.100.64/27 not-advertise
#   area 0.0.0.100 range 198.51.100.96/27 cost 120
#   area 0.0.0.101 authentication message-digest
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#     redistribute static route-map zone1-static-connect
#     summary-address 198.51.100.128/27 tag 121
#     summary-address 198.51.100.160/27
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

# Using replaced

# Before state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospf .*"
# router ospf 100
#   router-id 203.0.113.20
# router ospf 102
#   router-id 198.51.100.1
#   redistribute direct route-map ospf102-direct-connect
#   redistribute eigrp 120 route-map rmap_1
#   area 0.0.0.100 filter-list route-map rmap_2 out
#   area 0.0.0.100 filter-list route-map rmap_1 in
#   area 0.0.0.100 range 198.51.100.64/27 not-advertise
#   area 0.0.0.100 range 198.51.100.96/27 cost 120
#   area 0.0.0.101 authentication message-digest
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#     redistribute static route-map zone1-static-connect
#     summary-address 198.51.100.128/27 tag 121
#     summary-address 198.51.100.160/27
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

- name: Replace device configurations of listed OSPF processes with provided configurations
  cisco.nxos.nxos_ospfv2:
    config:
      processes:
      - process_id: 102
        router_id: 198.51.100.1
        areas:
        - area_id: 0.0.0.100
          filter_list:
          - route_map: rmap_8
            direction: in
          ranges:
          - prefix: 198.51.100.64/27
            not_advertise: true
        - area_id: 0.0.0.101
          stub:
            no_summary: true
        redistribute:
        - protocol: eigrp
          id: 130
          route_map: rmap_1
        - protocol: direct
          route_map: ospf102-direct-connect
        vrfs:
        - vrf: zone1
          router_id: 198.51.100.129
          redistribute:
          - protocol: bgp
            id: 65563
            route_map: zone1-bgp-connect
          areas:
          - area_id: 0.0.0.102
            nssa:
              default_information_originate: true
              no_summary: true
    state: replaced

# Task output
# -------------
# before:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - areas:
#      - area_id: 0.0.0.100
#        filter_list:
#        - direction: out
#          route_map: rmap_2
#        - direction: in
#          route_map: rmap_1
#        ranges:
#        - not_advertise: true
#          prefix: 198.51.100.64/27
#        - cost: 120
#          prefix: 198.51.100.96/27
#      - area_id: 0.0.0.101
#        authentication:
#          message_digest: true
#      process_id: "102"
#      redistribute:
#      - protocol: direct
#        route_map: ospf102-direct-connect
#      - id: "120"
#        protocol: eigrp
#        route_map: rmap_1
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        redistribute:
#        - protocol: static
#          route_map: zone1-static-connect
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#
#  commands:
#  - router ospf 102
#  - redistribute eigrp 130 route-map rmap_1
#  - no redistribute eigrp 120 route-map rmap_1
#  - area 0.0.0.100 filter-list route-map rmap_8 in
#  - no area 0.0.0.100 filter-list route-map rmap_2 out
#  - no area 0.0.0.100 range 198.51.100.96/27
#  - no area 0.0.0.101 authentication
#  - area 0.0.0.101 stub no-summary
#  - vrf zone1
#  - no summary-address 198.51.100.128/27 tag 121
#  - no summary-address 198.51.100.160/27
#  - redistribute bgp 65563 route-map zone1-bgp-connect
#  - no redistribute static route-map zone1-static-connect
#  - no area 0.0.0.103 nssa
#  - no area 0.0.0.103 nssa translate type7 always
#  - no vrf zone2
#
# after:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - areas:
#      - area_id: 0.0.0.101
#        stub:
#          no_summary: true
#      - area_id: 0.0.0.100
#        filter_list:
#        - direction: in
#          route_map: rmap_8
#        ranges:
#        - not_advertise: true
#          prefix: 198.51.100.64/27
#      process_id: "102"
#      redistribute:
#      - protocol: direct
#        route_map: ospf102-direct-connect
#      - id: "130"
#        protocol: eigrp
#        route_map: rmap_1
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        redistribute:
#        - id: "65563"
#          protocol: bgp
#          route_map: zone1-bgp-connect
#        router_id: 198.51.100.129
#        vrf: zone1

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospf .*"
# router ospf 100
#   router-id 203.0.113.20
# router ospf 102
#   router-id 198.51.100.1
#   area 0.0.0.101 stub no-summary
#   redistribute direct route-map ospf102-direct-connect
#   redistribute eigrp 130 route-map rmap_1
#   area 0.0.0.100 filter-list route-map rmap_8 in
#   area 0.0.0.100 range 198.51.100.64/27 not-advertise
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     redistribute bgp 65563 route-map zone1-bgp-connect

# Using overridden

# Before state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospf .*"
# router ospf 100
#   router-id 203.0.113.20
# router ospf 102
#   router-id 198.51.100.1
#   redistribute direct route-map ospf102-direct-connect
#   redistribute eigrp 120 route-map rmap_1
#   area 0.0.0.100 filter-list route-map rmap_2 out
#   area 0.0.0.100 filter-list route-map rmap_1 in
#   area 0.0.0.100 range 198.51.100.64/27 not-advertise
#   area 0.0.0.100 range 198.51.100.96/27 cost 120
#   area 0.0.0.101 authentication message-digest
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#     redistribute static route-map zone1-static-connect
#     summary-address 198.51.100.128/27 tag 121
#     summary-address 198.51.100.160/27
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

- name: Override all OSPF configuration with provided configuration
  cisco.nxos.nxos_ospfv2:
    config:
      processes:
      - process_id: 104
        router_id: 203.0.113.20
      - process_id: 102
        router_id: 198.51.100.1
        shutdown: true
    state: overridden

# Task output
# -------------
# before:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - areas:
#      - area_id: 0.0.0.100
#        filter_list:
#        - direction: out
#          route_map: rmap_2
#        - direction: in
#          route_map: rmap_1
#        ranges:
#        - not_advertise: true
#          prefix: 198.51.100.64/27
#        - cost: 120
#          prefix: 198.51.100.96/27
#      - area_id: 0.0.0.101
#        authentication:
#          message_digest: true
#      process_id: "102"
#      redistribute:
#      - protocol: direct
#        route_map: ospf102-direct-connect
#      - id: "120"
#        protocol: eigrp
#        route_map: rmap_1
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        redistribute:
#        - protocol: static
#          route_map: zone1-static-connect
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#
# commands:
#  - no router ospf 100
#  - router ospf 104
#  - router-id 203.0.113.20
#  - router ospf 102
#  - shutdown
#  - no redistribute direct route-map ospf102-direct-connect
#  - no redistribute eigrp 120 route-map rmap_1
#  - no area 0.0.0.100 filter-list route-map rmap_2 out
#  - no area 0.0.0.100 filter-list route-map rmap_1 in
#  - no area 0.0.0.100 range 198.51.100.64/27
#  - no area 0.0.0.100 range 198.51.100.96/27
#  - no area 0.0.0.101 authentication
#  - no vrf zone1
#  - no vrf zone2
#
# after:
#    processes:
#    - process_id: "102"
#      router_id: 198.51.100.1
#      shutdown: true
#    - process_id: "104"
#      router_id: 203.0.113.20

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospf .*"
# router ospf 102
#   router-id 198.51.100.1
#   shutdown
# router ospf 104
#   router-id 203.0.113.20

# Using deleted to delete a single OSPF process

# Before state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospf .*"
# router ospf 100
#   router-id 203.0.113.20
# router ospf 102
#   router-id 198.51.100.1
#   redistribute direct route-map ospf102-direct-connect
#   redistribute eigrp 120 route-map rmap_1
#   area 0.0.0.100 filter-list route-map rmap_2 out
#   area 0.0.0.100 filter-list route-map rmap_1 in
#   area 0.0.0.100 range 198.51.100.64/27 not-advertise
#   area 0.0.0.100 range 198.51.100.96/27 cost 120
#   area 0.0.0.101 authentication message-digest
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#     redistribute static route-map zone1-static-connect
#     summary-address 198.51.100.128/27 tag 121
#     summary-address 198.51.100.160/27
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

- name: Delete a single OSPF process
  cisco.nxos.nxos_ospfv2:
    config:
      processes:
      - process_id: 102
    state: deleted

# Task output
# -------------
# before:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - areas:
#      - area_id: 0.0.0.100
#        filter_list:
#        - direction: out
#          route_map: rmap_2
#        - direction: in
#          route_map: rmap_1
#        ranges:
#        - not_advertise: true
#          prefix: 198.51.100.64/27
#        - cost: 120
#          prefix: 198.51.100.96/27
#      - area_id: 0.0.0.101
#        authentication:
#          message_digest: true
#      process_id: "102"
#      redistribute:
#      - protocol: direct
#        route_map: ospf102-direct-connect
#      - id: "120"
#        protocol: eigrp
#        route_map: rmap_1
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        redistribute:
#        - protocol: static
#          route_map: zone1-static-connect
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#
# commands:
#  - no router ospf 102
#
# after:
#   processes:
#   - process_id: "100"
#     router_id: 203.0.113.20

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospf .*"
# router ospf 100
#   router-id 203.0.113.20

# Using deleted all OSPF processes from the device

# Before state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospf .*"
# router ospf 100
#   router-id 203.0.113.20
# router ospf 102
#   router-id 198.51.100.1
#   redistribute direct route-map ospf102-direct-connect
#   redistribute eigrp 120 route-map rmap_1
#   area 0.0.0.100 filter-list route-map rmap_2 out
#   area 0.0.0.100 filter-list route-map rmap_1 in
#   area 0.0.0.100 range 198.51.100.64/27 not-advertise
#   area 0.0.0.100 range 198.51.100.96/27 cost 120
#   area 0.0.0.101 authentication message-digest
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#     redistribute static route-map zone1-static-connect
#     summary-address 198.51.100.128/27 tag 121
#     summary-address 198.51.100.160/27
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

- name: Delete all OSPF processes from the device
  cisco.nxos.nxos_ospfv2:
    state: deleted

# Task output
# -------------
# before:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - areas:
#      - area_id: 0.0.0.100
#        filter_list:
#        - direction: out
#          route_map: rmap_2
#        - direction: in
#          route_map: rmap_1
#        ranges:
#        - not_advertise: true
#          prefix: 198.51.100.64/27
#        - cost: 120
#          prefix: 198.51.100.96/27
#      - area_id: 0.0.0.101
#        authentication:
#          message_digest: true
#      process_id: "102"
#      redistribute:
#      - protocol: direct
#        route_map: ospf102-direct-connect
#      - id: "120"
#        protocol: eigrp
#        route_map: rmap_1
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        redistribute:
#        - protocol: static
#          route_map: zone1-static-connect
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#
# commands:
#  - no router ospf 100
#  - no router ospf 102
#
#  after: {}

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospf .*"
# nxos-9k-rdo#

# Using rendered

- name: Render platform specific configuration lines (without connecting to the device)
  cisco.nxos.nxos_ospfv2:
    config:
      processes:
      - process_id: 100
        router_id: 203.0.113.20
      - process_id: 102
        router_id: 198.51.100.1
        areas:
        - area_id: 0.0.0.100
          filter_list:
          - route_map: rmap_1
            direction: in
          - route_map: rmap_2
            direction: out
          ranges:
          - prefix: 198.51.100.64/27
            not_advertise: true
          - prefix: 198.51.100.96/27
            cost: 120
        - area_id: 0.0.0.101
          authentication:
            message_digest: true
        redistribute:
        - protocol: eigrp
          id: 120
          route_map: rmap_1
        - protocol: direct
          route_map: ospf102-direct-connect
        vrfs:
        - vrf: zone1
          router_id: 198.51.100.129
          redistribute:
          - protocol: static
            route_map: zone1-static-connect
          summary_address:
          - prefix: 198.51.100.128/27
            tag: 121
          - prefix: 198.51.100.160/27
          areas:
          - area_id: 0.0.0.102
            nssa:
              default_information_originate: true
              no_summary: true
          - area_id: 0.0.0.103
            nssa:
              no_summary: true
              translate:
                type7:
                  always: true
        - vrf: zone2
          auto_cost:
            reference_bandwidth: 45
            unit: Gbps
    state: rendered

# Task Output (redacted)
# -----------------------
# rendered:
#  - router ospf 100
#  - router-id 203.0.113.20
#  - router ospf 102
#  - router-id 198.51.100.1
#  - redistribute eigrp 120 route-map rmap_1
#  - redistribute direct route-map ospf102-direct-connect
#  - area 0.0.0.100 filter-list route-map rmap_1 in
#  - area 0.0.0.100 filter-list route-map rmap_2 out
#  - area 0.0.0.100 range 198.51.100.64/27 not-advertise
#  - area 0.0.0.100 range 198.51.100.96/27 cost 120
#  - area 0.0.0.101 authentication message-digest
#  - vrf zone1
#  - router-id 198.51.100.129
#  - summary-address 198.51.100.128/27 tag 121
#  - summary-address 198.51.100.160/27
#  - redistribute static route-map zone1-static-connect
#  - area 0.0.0.102 nssa no-summary default-information-originate
#  - area 0.0.0.103 nssa no-summary
#  - area 0.0.0.103 nssa translate type7 always
#  - vrf zone2
#  - auto-cost reference-bandwidth 45 Gbps

# Using parsed

# parsed.cfg
# ------------
# router ospf 100
#   router-id 192.0.100.1
#   area 0.0.0.101 nssa no-summary no-redistribution
#   area 0.0.0.102 stub no-summary
#   redistribute direct route-map ospf-direct-connect
#   redistribute eigrp 120 route-map rmap_1
#   area 0.0.0.100 filter-list route-map rmap_2 out
#   area 0.0.0.100 filter-list route-map rmap_1 in
#   area 0.0.0.100 range 192.0.2.0/24 not-advertise
#   area 0.0.0.100 range 192.0.3.0/24 cost 120
#   area 0.0.0.100 authentication message-digest
#   vrf zone1
#     router-id 192.0.100.2
#     area 0.0.100.1 nssa no-summary no-redistribution
#     redistribute static route-map zone1-direct-connect
#     summary-address 10.0.0.0/24 tag 120
#     summary-address 11.0.0.0/24 not-advertise
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps
#     down-bit-ignore
#     capability vrf-lite evpn
#     shutdown
# router ospf 102
#   router-id 198.54.100.1
#   shutdown
#   vrf zone2
#     summary-address 192.0.8.0/24 tag 120
#   vrf zone4
#     shutdown

- name: Parse externally provided OSPFv2 config
  cisco.nxos.nxos_ospfv2:
    running_config: "{{ lookup('file', 'ospfv2.cfg') }}"
    state: parsed

# Task output (redacted)
# -----------------------
# parsed:
#   processes:
#   - process_id: "100"
#     areas:
#       - area_id: 0.0.0.101
#         nssa:
#           no_redistribution: true
#           no_summary: true
#       - area_id: 0.0.0.102
#         stub:
#           no_summary: true
#       - area_id: 0.0.0.100
#         authentication:
#           message_digest: true
#         filter_list:
#           - direction: out
#             route_map: rmap_2
#           - direction: in
#             route_map: rmap_1
#         ranges:
#           - not_advertise: true
#             prefix: 192.0.2.0/24
#           - cost: 120
#             prefix: 192.0.3.0/24
#     redistribute:
#       - protocol: direct
#         route_map: ospf-direct-connect
#       - id: "120"
#         protocol: eigrp
#         route_map: rmap_1
#     router_id: 192.0.100.1
#     vrfs:
#       - vrf: zone1
#         areas:
#           - area_id: 0.0.100.1
#             nssa:
#               no_redistribution: true
#               no_summary: true
#         redistribute:
#           - protocol: static
#             route_map: zone1-direct-connect
#         router_id: 192.0.100.2
#         summary_address:
#           - prefix: 10.0.0.0/24
#             tag: 120
#           - not_advertise: true
#             prefix: 11.0.0.0/24
#       - vrf: zone2
#         auto_cost:
#           reference_bandwidth: 45
#           unit: Gbps
#         capability:
#           vrf_lite:
#             evpn: true
#         down_bit_ignore: true
#         shutdown: true
#   - process_id: "102"
#     router_id: 198.54.100.1
#     shutdown: true
#     vrfs:
#       - vrf: zone2
#         summary_address:
#           - prefix: 192.0.8.0/24
#             tag: 120
#       - vrf: zone4
#         shutdown: true

# Using gathered

- name: Gather OSPFv2 facts using gathered
  cisco.nxos.nxos_ospfv2:
    state: gathered

# Task output (redacted)
# -----------------------
#  gathered:
#    processes:
#      - process_id: "102"
#        areas:
#          - area_id: 0.0.0.101
#            stub:
#              no_summary: true
#          - area_id: 0.0.0.100
#            filter_list:
#              - direction: in
#                route_map: rmap_8
#            ranges:
#              - not_advertise: true
#                prefix: 198.51.100.64/27
#        redistribute:
#          - protocol: direct
#            route_map: ospf102-direct-connect
#          - id: "130"
#            protocol: eigrp
#            route_map: rmap_1
#        router_id: 198.51.100.1
#        vrfs:
#          - vrf: zone1
#            areas:
#              - area_id: 0.0.0.102
#                nssa:
#                  default_information_originate: true
#                  no_summary: true
#            redistribute:
#             - id: "65563"
#               protocol: bgp
#               route_map: zone1-bgp-connect
#            router_id: 198.51.100.129
#

Return Values 

Common return values are documented here, the following are the fields unique to this module:

Key	Description
after dictionary	The resulting configuration model invocation. Returned: when changed Sample: “The configuration returned will always be in the same format\n of the parameters above.\n”
before dictionary	The configuration prior to the model invocation. Returned: always Sample: “The configuration returned will always be in the same format\n of the parameters above.\n”
commands list / elements=string	The set of commands pushed to the remote device. Returned: always Sample: [“router ospf 102”, “router-id 198.54.100.1”, “router ospf 100”, “router-id 192.0.100.1”, “redistribute eigrp 120 route-map rmap_1”, “redistribute direct route-map ospf-direct-connect”, “area 0.0.0.100 filter-list route-map rmap_1 in”, “area 0.0.0.100 filter-list route-map rmap_2 out”, “area 0.0.0.100 range 192.0.2.0/24 not-advertise”, “area 0.0.0.100 range 192.0.3.0/24 cost 120”, “vrf zone1”, “router-id 192.0.100.2”, “summary-address 10.0.0.0/24 tag 121”, “summary-address 11.0.0.0/24”, “redistribute static route-map zone1-direct-connect”, “vrf zone2”, “auto-cost reference-bandwidth 45 Gbps”, “capability vrf-lite evpn”]

Authors

Nilashish Chakraborty (@NilashishC)

cisco.nxos.nxos_ospfv2 – OSPFv2 resource module

Synopsis

Parameters

Notes

Examples

Return Values

Authors

Synopsis 

Parameters 

Notes 

Examples 

Return Values 