You are reading an unmaintained version of the Ansible documentation. Unmaintained Ansible versions can contain unfixed security vulnerabilities (CVE). Please upgrade to a maintained version. See the latest Ansible documentation.

cisco.iosxr.iosxr_interface module – (deprecated, removed after 2022-06-01) Manage Interface on Cisco IOS XR network devices

Note

This module is part of the cisco.iosxr collection (version 2.9.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install cisco.iosxr.

To use it in a playbook, specify: cisco.iosxr.iosxr_interface.

New in version 1.0.0: of cisco.iosxr

DEPRECATED
Synopsis
Requirements
Parameters
Notes
Examples
Return Values
Status

DEPRECATED 

Removed in: major release after 2022-06-01
Why: Newer and updated modules released with more functionality in Ansible 2.9
Alternative: iosxr_interfaces

Synopsis 

This module provides declarative management of Interfaces on Cisco IOS XR network devices.

Requirements 

The below requirements are needed on the host that executes this module.

ncclient >= 0.5.3 when using netconf
lxml >= 4.1.1 when using netconf

Parameters 

Parameter	Comments
active string	Whether the interface is `active` or `preconfigured`. Preconfiguration allows you to configure modular services cards before they are inserted into the router. When the cards are inserted, they are instantly configured. Active cards are the ones already inserted. Choices: active ← (default) preconfigure
aggregate list / elements=dictionary	List of interfaces definition
active string	Whether the interface is `active` or `preconfigured`. Preconfiguration allows you to configure modular services cards before they are inserted into the router. When the cards are inserted, they are instantly configured. Active cards are the ones already inserted. Choices: active preconfigure
delay integer	Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values `up`/`down`, tx_rate and rx_rate.
description string	Description of Interface being configured.
duplex string	Configures the interface duplex mode. Default is auto-negotiation when not configured. Choices: full half
enabled boolean	Removes the shutdown configuration, which removes the forced administrative down on the interface, enabling it to move to an up or down state. Choices: no yes
mtu string	Sets the MTU value for the interface. Range is between 64 and 65535’
name string / required	Name of the interface to configure in `type + path` format. e.g. `GigabitEthernet0/0/0/0`
rx_rate string	Receiver rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
speed string	Configure the speed for an interface. Default is auto-negotiation when not configured. Choices: 10 100 1000
state string	State of the Interface configuration, `up` means present and operationally up and `down` means present and operationally `down` Choices: present absent up down
tx_rate string	Transmit rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
delay integer	Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values `up`/`down`, tx_rate and rx_rate. Default: 10
description string	Description of Interface being configured.
duplex string	Configures the interface duplex mode. Default is auto-negotiation when not configured. Choices: full half
enabled boolean	Removes the shutdown configuration, which removes the forced administrative down on the interface, enabling it to move to an up or down state. Choices: no yes ← (default)
mtu string	Sets the MTU value for the interface. Range is between 64 and 65535’
name string	Name of the interface to configure in `type + path` format. e.g. `GigabitEthernet0/0/0/0`
provider dictionary	Deprecated Starting with Ansible 2.5 we recommend using `connection: network_cli`. For more information please see the Network Guide. A dict object containing connection details.
host string	Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
password string	Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_PASSWORD` will be used instead.
port integer	Specifies the port to use when building the connection to the remote device.
ssh_keyfile path	Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_SSH_KEYFILE` will be used instead.
timeout integer	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
transport string	Specifies the type of connection based transport. Choices: cli ← (default) netconf
username string	Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_USERNAME` will be used instead.
rx_rate string	Receiver rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
speed string	Configure the speed for an interface. Default is auto-negotiation when not configured. Choices: 10 100 1000
state string	State of the Interface configuration, `up` means present and operationally up and `down` means present and operationally `down` Choices: present ← (default) absent up down
tx_rate string	Transmit rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules

Notes 

Note

This module works with connection network_cli and netconf. See the IOS-XR Platform Options.
Tested against IOS XRv 6.1.3.
Preconfiguration of physical interfaces is not supported with netconf transport.
For more information on using Ansible to manage network devices see the Ansible Network Guide
For more information on using Ansible to manage Cisco devices see the Cisco integration page.

Examples 

- name: configure interface
  cisco.iosxr.iosxr_interface:
    name: GigabitEthernet0/0/0/2
    description: test-interface
    speed: 100
    duplex: half
    mtu: 512

- name: remove interface
  cisco.iosxr.iosxr_interface:
    name: GigabitEthernet0/0/0/2
    state: absent

- name: make interface up
  cisco.iosxr.iosxr_interface:
    name: GigabitEthernet0/0/0/2
    enabled: true

- name: make interface down
  cisco.iosxr.iosxr_interface:
    name: GigabitEthernet0/0/0/2
    enabled: false

- name: Create interface using aggregate
  cisco.iosxr.iosxr_interface:
    aggregate:
    - name: GigabitEthernet0/0/0/3
    - name: GigabitEthernet0/0/0/2
    speed: 100
    duplex: full
    mtu: 512
    state: present

- name: Create interface using aggregate along with additional params in aggregate
  cisco.iosxr.iosxr_interface:
    aggregate:
    - {name: GigabitEthernet0/0/0/3, description: test-interface 3}
    - {name: GigabitEthernet0/0/0/2, description: test-interface 2}
    speed: 100
    duplex: full
    mtu: 512
    state: present

- name: Delete interface using aggregate
  cisco.iosxr.iosxr_interface:
    aggregate:
    - name: GigabitEthernet0/0/0/3
    - name: GigabitEthernet0/0/0/2
    state: absent

- name: Check intent arguments
  cisco.iosxr.iosxr_interface:
    name: GigabitEthernet0/0/0/5
    state: up
    delay: 20

- name: Config + intent
  cisco.iosxr.iosxr_interface:
    name: GigabitEthernet0/0/0/5
    enabled: false
    state: down
    delay: 20

Return Values 

Common return values are documented here, the following are the fields unique to this module:

Key

Description

commands

list / elements=string

The list of configuration mode commands sent to device with transport cli

Returned: always (empty list when no commands to send)

Sample: [“interface GigabitEthernet0/0/0/2”, “description test-interface”, “duplex half”, “mtu 512”]

xml

list / elements=string

NetConf rpc xml sent to device with transport netconf

Returned: always (empty list when no xml rpc to send)

Sample: [“\u003cconfig xmlns:xc=\”urn:ietf:params:xml:ns:netconf:base:1.0\”\u003e \u003cinterface-configurations xmlns=\”http://cisco.com/ns/yang/Cisco-IOS-XR-ifmgr-cfg\”\u003e \u003cinterface-configuration xc:operation=\”merge\”\u003e \u003cactive\u003eact\u003c/active\u003e \u003cinterface-name\u003eGigabitEthernet0/0/0/0\u003c/interface-name\u003e \u003cdescription\u003etest-interface-0\u003c/description\u003e \u003cmtus\u003e\u003cmtu\u003e \u003cowner\u003eGigabitEthernet\u003c/owner\u003e \u003cmtu\u003e512\u003c/mtu\u003e \u003c/mtu\u003e\u003c/mtus\u003e \u003cethernet xmlns=\”http://cisco.com/ns/yang/Cisco-IOS-XR-drivers-media-eth-cfg\”\u003e \u003cspeed\u003e100\u003c/speed\u003e \u003cduplex\u003ehalf\u003c/duplex\u003e \u003c/ethernet\u003e \u003c/interface-configuration\u003e \u003c/interface-configurations\u003e\u003c/config\u003e”]

Status 

This module will be removed in a major release after 2022-06-01. [deprecated]
For more information see DEPRECATED.

Authors

Ganesh Nalawade (@ganeshrn)
Kedar Kekan (@kedarX)

Collection links

Issue Tracker Repository (Sources)