cisco.iosxr.iosxr_ospfv3 module – ospfv3 resource module

Note

This module is part of the cisco.iosxr collection (version 2.9.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install cisco.iosxr.

To use it in a playbook, specify: cisco.iosxr.iosxr_ospfv3.

New in version 1.1.0: of cisco.iosxr

Synopsis

  • This module manages global ospfv3 configuration on devices running Cisco IOS-XR

Parameters

Parameter

Comments

config

dictionary

A list of ospfv3 process configuration

processes

list / elements=dictionary

A list of ospfv3 instances configuration

address_family_unicast

boolean

Enable unicast topology for ipv4 address family

Choices:

  • no

  • yes

areas

list / elements=dictionary

Configure ospfv3 areas’ properties

area_id

string / required

Area ID as IP address or integer

authentication

dictionary

Enable authentication

disable

boolean

Do not authenticate OSPFv3 packets

Choices:

  • no ← (default)

  • yes

ipsec

dictionary

Specify IPSec AH authentication attributes

algorithim_type

string

Specify the type of algorithim

Choices:

  • md5

  • sha1

clear_key

string

Specify key in cleartext form

key

string

Specify key

password_key

string

Specify key in encrypted form

spi

integer

Specify the Security Parameter Index value

bfd

dictionary

Configure BFD parameters

fast_detect

dictionary

Configure fast detection

set

boolean

Enable fast detection only

Choices:

  • no

  • yes

strict_mode

boolean

Hold down neighbor session until BFD session is up

Choices:

  • no

  • yes

minimum_interval

integer

Hello interval in milli-seconds

multiplier

integer

Detect multiplier

cost

integer

Interface cost

database_filter

dictionary

Filter LSAs during synchronization and flooding

all_outgoing_lsa

boolean

Filter all outgoing LSA

Choices:

  • no

  • yes

dead_interval

integer

Interval after which a neighbor is declared dead

default_cost

integer

Set the summary default-cost of a NSSA/stub area. Stub’s advertised external route metric

demand_circuit

boolean

Enable/Disable ospfv3 demand circuit

Choices:

  • no

  • yes

distrinbute_rib_prefix_list_name

string

Filter LSAs during synchronization and flooding

encryption

dictionary

Encrypt and authenticate OSPFv3 packets

disable

boolean

Do not encrypt OSPFv3 packets

Choices:

  • no ← (default)

  • yes

ipsec

dictionary

Specify IPSec ESP encryption and authentication

esp

dictionary

Specify encryption parameters

aes

dictionary

This specify the aes algorithim

algorithim_type

string

Specify the bit encryption for aes algorithim

Choices:

  • 192

  • 256

clear_key

string

Specify AES key in cleartext form

key

string

Cleartext AES key

password_key

string

Specify AES key in encrypted form

des

dictionary

This specify the des algorithim

clear_key

string

Specify AES key in cleartext form

key

string

Cleartext AES key

password_key

string

Specify AES key in encrypted form

null_encryption

dictionary

Specify null encryption attributes

authentication

dictionary

Specify authentication parameters

algorithim_type

string

Specify the type of algorithim

Choices:

  • md5

  • sha1

clear_key

string

Specify key in cleartext form

key

string

Specify key

password_key

string

Specify key in encrypted form

triple_des

dictionary

This specify the triple DES algorithim

clear_key

string

Specify 3DES key in cleartext form

key

string

Cleartext 3DES key

password_key

string

Specify 3DES key in encrypted form

spi

integer

Specify the Security Parameter Index value

fast_reroute

dictionary

Specify IP Fast Reroute

disabled

boolean

Disable IP fast reroute

Choices:

  • no

  • yes

dictionary

Specify per-prefix computation

string

Specify per-link LFA exclusion or FRR LFA candidate information

Choices:

  • exclude

  • lfa_candidate

dictionary

Specify Per-link LFA exclusion information

list / elements=integer

Specify Aggregated Ethernet interface(s)

list / elements=integer

Specify Bridge-Group Virtual Interface

list / elements=string

Specify FastEthernet/IEEE 802.3 interface(s)

list / elements=string

Specify FiftyGigE/IEEE 802.3 interface(s)

list / elements=string

Specify FortyGigE/IEEE 802.3 interface(s)

list / elements=string

Specify FourHundredGigE/IEEE 802.3 interface(s)

list / elements=string

Specify GigabitEthernet/IEEE 802.3 interface(s)

list / elements=string

Specify HundredGigE/IEEE 802.3 interface(s)

list / elements=string

Specify MgmtEth/IEEE 802.3 interface(s)

list / elements=string

Specify Multilink network interface(s)

list / elements=integer

Specify Network Virtualization Endpoint Interface(s)

list / elements=integer

Specify Aggregated pos interface(s)

list / elements=integer

Specify PWHE Ethernet Interface

list / elements=integer

Specify PWHE VC11 IP Interworking Interface

list / elements=string

Specify Serial network interface(s)

list / elements=string

Specify SRP interface(s)

list / elements=string

Specify TenGigabitEthernet/IEEE 802.3 interface(s)

list / elements=integer

Specify GRE/IPinIP Tunnel Interface(s)

list / elements=integer

Specify IPSec Tunnel interface(s)

integer

MPLS Transport Protocol Tunnel interface

list / elements=integer

Specify MPLS Traffic Engineering P2MP Tunnel interface(s)

list / elements=string

Specify TwentyFiveGigabitEthernet/IEEE 802.3 interface(s)

list / elements=string

Specify TwoHundredGigE/IEEE 802.3 interface(s)

boolean

Enable/Disable backup selection from candidate-list only

Choices:

  • no

  • yes

per_prefix

dictionary

Specify per-prefix computation

information_type

string

Specify per_prefix LFA exclusion or FRR LFA candidate information

Choices:

  • exclude

  • lfa_candidate

interface

dictionary

Specify Per-link LFA exclusion information

bundle_ether

list / elements=integer

Specify Aggregated Ethernet interface(s)

bvi

list / elements=integer

Specify Bridge-Group Virtual Interface

fast_ethernet

list / elements=string

Specify FastEthernet/IEEE 802.3 interface(s)

fiftygige

list / elements=string

Specify FiftyGigE/IEEE 802.3 interface(s)

fortygige

list / elements=string

Specify FortyGigE/IEEE 802.3 interface(s)

fourhundredgige

list / elements=string

Specify FourHundredGigE/IEEE 802.3 interface(s)

gigabitethernet

list / elements=string

Specify GigabitEthernet/IEEE 802.3 interface(s)

hundredgige

list / elements=string

Specify HundredGigE/IEEE 802.3 interface(s)

mgmteth

list / elements=string

Specify MgmtEth/IEEE 802.3 interface(s)

list / elements=string

Specify Multilink network interface(s)

nve

list / elements=integer

Specify Network Virtualization Endpoint Interface(s)

pos_int

list / elements=integer

Specify Aggregated pos interface(s)

pw_ether

list / elements=integer

Specify PWHE Ethernet Interface

pw_iw

list / elements=integer

Specify PWHE VC11 IP Interworking Interface

serial

list / elements=string

Specify Serial network interface(s)

srp

list / elements=string

Specify SRP interface(s)

tengige

list / elements=string

Specify TenGigabitEthernet/IEEE 802.3 interface(s)

tunnel_ip

list / elements=integer

Specify GRE/IPinIP Tunnel Interface(s)

tunnel_ipsec

list / elements=integer

Specify IPSec Tunnel interface(s)

tunnel_mpls

integer

MPLS Transport Protocol Tunnel interface

tunnel_mte

list / elements=integer

Specify MPLS Traffic Engineering P2MP Tunnel interface(s)

twentyfivegige

list / elements=string

Specify TwentyFiveGigabitEthernet/IEEE 802.3 interface(s)

twohundredgige

list / elements=string

Specify TwoHundredGigE/IEEE 802.3 interface(s)

use_candidate_only

boolean

Enable/Disable backup selection from candidate-list only

Choices:

  • no

  • yes

flood_reduction

boolean

Enable/Disable flood reduction

Choices:

  • no

  • yes

hello_interval

integer

Specify Time between HELLO packets

instance_id

integer

Specify instance ID

mpls_ldp_sync

boolean

Enable/Disable MPLS LDP Sync

Choices:

  • no

  • yes

mtu_ignore

boolean

Enable/Disable ignoring of MTU in DBD packets

Choices:

  • no

  • yes

network

string

Specify Network type

Choices:

  • broadcast

  • non-broadcast

  • point-to-multipoint

  • point-to-point

nssa

dictionary

NSSA settings for the area

default_information_originate

dictionary

Originate default Type 7 LSA

metric

integer

ospfv3 default metric

metric_type

integer

Metric type for default routes

set

boolean

Set nssa to default information originate

Choices:

  • no

  • yes

no_redistribution

boolean

Do not send redistributed LSAs into NSSA area

Choices:

  • no

  • yes

no_summary

boolean

Do not send summary LSAs into NSSA area

Choices:

  • no

  • yes

set

boolean

Configure area as NSSA

Choices:

  • no

  • yes

translate

dictionary

Translate LSA

type7

dictionary

Translate from Type 7 to Type 5

always

boolean / required

Always translate LSAs

Choices:

  • no

  • yes

packet_size

integer

Specify limit size of OSPFv3 packets

passive

boolean

Enable/Disable routing updates on an interface

Choices:

  • no

  • yes

prefix_suppression

boolean

Hide all transit addresses on this interface

Choices:

  • no

  • yes

priority

integer

Specify Router priority

ranges

list / elements=dictionary

Summarize routes matching address/mask (border routers only)

address

string / required

IP in Prefix format (X:X::X/length)

advertise

boolean

Advertise this range (default)

Choices:

  • no

  • yes

cost

integer

Specify user specified metric for this range

not_advertise

boolean

DoNotAdvertise this range

Choices:

  • no

  • yes

retransmit_interval

integer

Specify Delay between LSA retransmissions

stub

dictionary

Settings for configuring the area as a stub

no_summary

boolean

Do not send summary LSA into stub area

Choices:

  • no

  • yes

set

boolean

Configure the area as a stub

Choices:

  • no

  • yes

transmit_delay

integer

Specify estimated time needed to send link-state update packet

list / elements=dictionary

Define a virtual link

dictionary

Enable authentication

boolean

Do not authenticate OSPFv3 packets

Choices:

  • no ← (default)

  • yes

dictionary

Specify IPSec AH authentication attributes

string

Specify the type of algorithim

Choices:

  • md5

  • sha1

string

Specify key in cleartext form

string

Specify key

string

Specify key in encrypted form

integer

Specify the Security Parameter Index value

integer

Interval after which a neighbor is declared dead

dictionary

Encrypt and authenticate OSPFv3 packets

boolean

Do not encrypt OSPFv3 packets

Choices:

  • no ← (default)

  • yes

dictionary

Specify IPSec ESP encryption and authentication

dictionary

Specify encryption parameters

dictionary

This specify the aes algorithim

string

Specify the bit encryption for aes algorithim

Choices:

  • 192

  • 256

string

Specify AES key in cleartext form

string

Cleartext AES key

string

Specify AES key in encrypted form

dictionary

This specify the des algorithim

string

Specify AES key in cleartext form

string

Cleartext AES key

string

Specify AES key in encrypted form

dictionary

Specify null encryption attributes

dictionary

Specify authentication parameters

string

Specify the type of algorithim

Choices:

  • md5

  • sha1

string

Specify key in cleartext form

string

Specify key

string

Specify key in encrypted form

dictionary

This specify the triple DES algorithim

string

Specify 3DES key in cleartext form

string

Cleartext 3DES key

string

Specify 3DES key in encrypted form

integer

Specify the Security Parameter Index value

integer

Time between HELLO packets

string / required

Router-ID of virtual link neighbor (A.B.C.D)

integer

Delay between LSA retransmissions

integer

Link state transmit delay

authentication

dictionary

Enable authentication

disable

boolean

Do not authenticate OSPFv3 packets

Choices:

  • no ← (default)

  • yes

ipsec

dictionary

Specify IPSec AH authentication attributes

algorithim_type

string

Specify the type of algorithim

Choices:

  • md5

  • sha1

clear_key

string

Specify key in cleartext form

key

string

Specify key

password_key

string

Specify key in encrypted form

spi

integer

Specify the Security Parameter Index value

auto_cost

dictionary

Calculate ospfv3 interface cost according to bandwidth

disable

boolean

Assign ospfv3 cost based on interface type

Choices:

  • no

  • yes

reference_bandwidth

integer

Specify reference bandwidth in megabits per sec

bfd

dictionary

Configure BFD parameters

fast_detect

dictionary

Configure fast detection

set

boolean

Enable fast detection only

Choices:

  • no

  • yes

strict_mode

boolean

Hold down neighbor session until BFD session is up

Choices:

  • no

  • yes

minimum_interval

integer

Hello interval in milli-seconds

multiplier

integer

Detect multiplier

capability

dictionary

Enable specific OSPFv3 feature

type7

dictionary

Specify type7 nssa capability

prefer

boolean

Prefer type7 externals over type5

Choices:

  • no

  • yes

translate

boolean

Translate type7 to type5

Choices:

  • no

  • yes

cost

integer

Specify Interface cost

database_filter

dictionary

Filter LSAs during synchronization and flooding

all_outgoing_lsa

boolean

Filter all outgoing LSA

Choices:

  • no

  • yes

dead_interval

integer

Interval after which a neighbor is declared dead

default_information_originate

dictionary

Control distribution of default information

always

boolean

Always advertise default route

Choices:

  • no

  • yes

metric

integer

ospfv3 default metric

metric_type

integer

ospfv3 metric type for default routes

route_policy

string

Apply route-policy to default-information origination

set

boolean

Enable distribution of default route

Choices:

  • no

  • yes

tag

integer

Set tag for default route

default_metric

integer

Set metric of redistributed routes

demand_circuit

boolean

Enable/Disable ospfv3 demand circuit

Choices:

  • no

  • yes

distance

dictionary

Define an administrative distance

admin_distance

integer

Administrative distance

ospfv3_distance

dictionary

ospfv3 administrative distance

external

integer

Distance for external routes

inter_area

integer

Distance for inter-area routes

intra_area

integer

Distance for intra-area routes

distribute_list

dictionary

Filter prefixes to/from RIB

prefix_list

list / elements=string

Filter prefixes based on an IPv6 prefix-list

in

boolean

Filter prefixes installed to RIB

Choices:

  • no

  • yes

name

string

Specify Prefix-list name

out

boolean

Filter prefixes redistributed from RIB

Choices:

  • no

  • yes

encryption

dictionary

Encrypt and authenticate OSPFv3 packets

disable

boolean

Do not encrypt OSPFv3 packets

Choices:

  • no ← (default)

  • yes

ipsec

dictionary

Specify IPSec ESP encryption and authentication

esp

dictionary

Specify encryption parameters

aes

dictionary

This specify the aes algorithim

algorithim_type

string

Specify the bit encryption for aes algorithim

Choices:

  • 192

  • 256

clear_key

string

Specify AES key in cleartext form

key

string

Cleartext AES key

password_key

string

Specify AES key in encrypted form

des

dictionary

This specify the des algorithim

clear_key

string

Specify AES key in cleartext form

key

string

Cleartext AES key

password_key

string

Specify AES key in encrypted form

null_encryption

dictionary

Specify null encryption attributes

authentication

dictionary

Specify authentication parameters

algorithim_type

string

Specify the type of algorithim

Choices:

  • md5

  • sha1

clear_key

string

Specify key in cleartext form

key

string

Specify key

password_key

string

Specify key in encrypted form

triple_des

dictionary

This specify the triple DES algorithim

clear_key

string

Specify 3DES key in cleartext form

key

string

Cleartext 3DES key

password_key

string

Specify 3DES key in encrypted form

spi

integer

Specify the Security Parameter Index value

fast_reroute

dictionary

Specify IP Fast Reroute

disabled

boolean

Disable IP fast reroute

Choices:

  • no

  • yes

dictionary

Specify per-prefix computation

string

Specify per-link LFA exclusion or FRR LFA candidate information

Choices:

  • exclude

  • lfa_candidate

dictionary

Specify Per-link LFA exclusion information

list / elements=integer

Specify Aggregated Ethernet interface(s)

list / elements=integer

Specify Bridge-Group Virtual Interface

list / elements=string

Specify FastEthernet/IEEE 802.3 interface(s)

list / elements=string

Specify FiftyGigE/IEEE 802.3 interface(s)

list / elements=string

Specify FortyGigE/IEEE 802.3 interface(s)

list / elements=string

Specify FourHundredGigE/IEEE 802.3 interface(s)

list / elements=string

Specify GigabitEthernet/IEEE 802.3 interface(s)

list / elements=string

Specify HundredGigE/IEEE 802.3 interface(s)

list / elements=string

Specify MgmtEth/IEEE 802.3 interface(s)

list / elements=string

Specify Multilink network interface(s)

list / elements=integer

Specify Network Virtualization Endpoint Interface(s)

list / elements=integer

Specify Aggregated pos interface(s)

list / elements=integer

Specify PWHE Ethernet Interface

list / elements=integer

Specify PWHE VC11 IP Interworking Interface

list / elements=string

Specify Serial network interface(s)

list / elements=string

Specify SRP interface(s)

list / elements=string

Specify TenGigabitEthernet/IEEE 802.3 interface(s)

list / elements=integer

Specify GRE/IPinIP Tunnel Interface(s)

list / elements=integer

Specify IPSec Tunnel interface(s)

integer

MPLS Transport Protocol Tunnel interface

list / elements=integer

Specify MPLS Traffic Engineering P2MP Tunnel interface(s)

list / elements=string

Specify TwentyFiveGigabitEthernet/IEEE 802.3 interface(s)

list / elements=string

Specify TwoHundredGigE/IEEE 802.3 interface(s)

boolean

Enable/Disable backup selection from candidate-list only

Choices:

  • no

  • yes

per_prefix

dictionary

Specify per-prefix computation

information_type

string

Specify per_prefix LFA exclusion or FRR LFA candidate information

Choices:

  • exclude

  • lfa_candidate

interface

dictionary

Specify Per-link LFA exclusion information

bundle_ether

list / elements=integer

Specify Aggregated Ethernet interface(s)

bvi

list / elements=integer

Specify Bridge-Group Virtual Interface

fast_ethernet

list / elements=string

Specify FastEthernet/IEEE 802.3 interface(s)

fiftygige

list / elements=string

Specify FiftyGigE/IEEE 802.3 interface(s)

fortygige

list / elements=string

Specify FortyGigE/IEEE 802.3 interface(s)

fourhundredgige

list / elements=string

Specify FourHundredGigE/IEEE 802.3 interface(s)

gigabitethernet

list / elements=string

Specify GigabitEthernet/IEEE 802.3 interface(s)

hundredgige

list / elements=string

Specify HundredGigE/IEEE 802.3 interface(s)

mgmteth

list / elements=string

Specify MgmtEth/IEEE 802.3 interface(s)

list / elements=string

Specify Multilink network interface(s)

nve

list / elements=integer

Specify Network Virtualization Endpoint Interface(s)

post_int

list / elements=integer

Specify Aggregated pos interface(s)

pw_ether

list / elements=integer

Specify PWHE Ethernet Interface

pw_iw

list / elements=integer

Specify PWHE VC11 IP Interworking Interface

serial

list / elements=string

Specify Serial network interface(s)

srp

list / elements=string

Specify SRP interface(s)

tengige

list / elements=string

Specify TenGigabitEthernet/IEEE 802.3 interface(s)

tunnel_ip

list / elements=integer

Specify GRE/IPinIP Tunnel Interface(s)

tunnel_ipsec

list / elements=integer

Specify IPSec Tunnel interface(s)

tunnel_mpls

integer

MPLS Transport Protocol Tunnel interface

tunnel_mte

list / elements=integer

Specify MPLS Traffic Engineering P2MP Tunnel interface(s)

twentyfivegige

list / elements=string

Specify TwentyFiveGigabitEthernet/IEEE 802.3 interface(s)

twohundredgige

list / elements=string

Specify TwoHundredGigE/IEEE 802.3 interface(s)

use_candidate_only

boolean

Enable/Disable backup selection from candidate-list only

Choices:

  • no

  • yes

flood_reduction

boolean

Enable/Disable flood reduction

Choices:

  • no

  • yes

graceful_restart

dictionary

Enable Graceful-Restart

helper_disable

boolean

Disable router’s helper support level

Choices:

  • no

  • yes

max_interval

integer

Maximum route lifetime following restart

min_interval

integer

Minimum interval between Graceful Restarts

set

boolean

Set graceful restart

Choices:

  • no

  • yes

hello_interval

integer

Specify Time between HELLO packets

ignore_mospf_type6_lsa

boolean

Ignore MOSPF Type 6 LSA

Choices:

  • no

  • yes

instance_id

integer

Specify instance ID

log_adjacency_changes

dictionary

Log adjacency state changes

detail

boolean

Log all state changes

Choices:

  • no

  • yes

disable

boolean

Disable log adjacency changes

Choices:

  • no

  • yes

set

boolean

Set log adjacency

Choices:

  • no

  • yes

maximum

dictionary

Set OSPFv3 limits

interfaces

integer

Specify limit for number of interfaces

paths

integer

Specify limit for number of paths

redistributed_prefixes

integer

Specify limit for number of redistributed prefixes

mpls_ldp_sync

boolean

Enable/Disable MPLS LDP Sync

Choices:

  • no

  • yes

mtu_ignore

boolean

Enable/Disable ignoring of MTU in DBD packets

Choices:

  • no

  • yes

network

string

Specify Network type

Choices:

  • broadcast

  • non-broadcast

  • point-to-multipoint

  • point-to-point

nsr

boolean

Enable/Disable NSR for all VRFs in this process

Choices:

  • no

  • yes

packet_size

integer

Specify limit size of OSPFv3 packets

passive

boolean

Enable/Disable routing updates on an interface

Choices:

  • no

  • yes

prefix_suppression

boolean

Hide all transit addresses on this interface

Choices:

  • no

  • yes

priority

integer

Specify Router priority

process_id

string / required

The OSPFv3 Process ID

protocol_shutdown

boolean

Gracefully shutdown the OSPFv3 protocol

Choices:

  • no

  • yes

redistribute

dictionary

Redistribute information from another routing Protocol

application

list / elements=dictionary

Specify application routes

id

string / required

OnePK Application name

metric

integer

Specify metric for redistributed routes

metric_type

integer

Specify OSPFv3 exterior metric type for redistributed routes

route_policy

string

Apply route policy to redistribution

set

boolean

Set application route

Choices:

  • no

  • yes

tag

integer

Set tag for routes redistributed into OSPFv3

bgp

list / elements=dictionary

Specify bgp routes

id

integer / required

BGP process name

metric

integer

Specify metric for redistributed routes

metric_type

integer

Specify OSPFv3 exterior metric type for redistributed routes

preserved_med

string

Specify preserve med of BGP routes

route_policy

string

Apply route policy to redistribution

set

boolean

Set bgp route number

Choices:

  • no

  • yes

tag

integer

Set tag for routes redistributed into OSPFv3

connected

dictionary

Specify connected routes

metric

integer

Specify metric for redistributed routes

metric_type

integer

Specify OSPFv3 exterior metric type for redistributed routes

route_policy

string

Apply route policy to redistribution

set

boolean

Set connected route

Choices:

  • no

  • yes

tag

integer

Set tag for routes redistributed into OSPFv3

eigrp

list / elements=dictionary

Specify eigrp routes

id

integer / required

EIGRP process name

match

string

Redistribution of EIGRP routes

Choices:

  • external

  • internal

metric

integer

Specify metric for redistributed routes

metric_type

integer

Specify OSPFv3 exterior metric type for redistributed routes

route_policy

string

Apply route policy to redistribution

set

boolean

Set bgp route number

Choices:

  • no

  • yes

tag

integer

Set tag for routes redistributed into OSPFv3

isis

list / elements=dictionary

Specify IS-IS routes

id

string / required

IS-IS name

level

string

Specify IS-IS level routes

Choices:

  • level-1

  • level-1-2

  • level-2

metric

integer

Specify metric for redistributed routes

metric_type

integer

Specify OSPFv3 exterior metric type for redistributed routes

route_policy

string

Apply route policy to redistribution

set

boolean

Set IS-IS route number

Choices:

  • no

  • yes

tag

integer

Set tag for routes redistributed into OSPFv3

mobile

dictionary

Specify mobile routes

metric

integer

Specify metric for redistributed routes

metric_type

integer

Specify OSPFv3 exterior metric type for redistributed routes

route_policy

string

Apply route policy to redistribution

set

boolean

Set mobile route number

Choices:

  • no

  • yes

tag

integer

Set tag for routes redistributed into OSPFv3

ospfv3

list / elements=dictionary

Specify ospfv3 routes

id

string / required

OSPFv3 process name

match

dictionary

Redistribution of OSPFv3 routes

external

integer

Redistribute OSPFv3 external routes

Choices:

  • 1

  • 2

internal

boolean

Redistribute OSPFv3 internal routes

Choices:

  • no

  • yes

nssa_external

integer

Redistribute NSSA OSPFv3 external routes

Choices:

  • 1

  • 2

metric

integer

Specify metric for redistributed routes

metric_type

integer

Specify OSPFv3 exterior metric type for redistributed routes

route_policy

string

Apply route policy to redistribution

set

boolean

Set ospfv3 route number

Choices:

  • no

  • yes

tag

integer

Set tag for routes redistributed into OSPFv3

static

dictionary

Specify static routes

metric

integer

Specify metric for redistributed routes

metric_type

integer

Specify OSPFv3 exterior metric type for redistributed routes

route_policy

string

Apply route policy to redistribution

set

boolean

Set static route

Choices:

  • no

  • yes

tag

integer

Set tag for routes redistributed into OSPFv3

subscriber

dictionary

Specify subscriber routes

metric

integer

Specify metric for redistributed routes

metric_type

integer

Specify OSPFv3 exterior metric type for redistributed routes

route_policy

string

Apply route policy to redistribution

set

boolean

Set static route

Choices:

  • no

  • yes

tag

integer

Set tag for routes redistributed into OSPFv3

retransmit_interval

integer

Delay between LSA retransmissions

router_id

string

ospfv3 router-id in IPv4 address format (A.B.C.D)

spf_prefix_priority

dictionary

Specify SPF configuration

disable

boolean

Disable SPF prefix priority

Choices:

  • no

  • yes

route_policy

list / elements=dictionary

Specify the route-policy to prioritize route install

name

string

Specify name of the policy

value

string

Specify parameter values for the policy ()

stub_router

dictionary

Enter stub router configuration submode

router_lsa

dictionary

Modify self originated router LSAs

advertise_with

string

Advertise LSAs with specified type

Choices:

  • max-metric

  • r-bit

  • v6-bit

always

boolean

Force ospfv3 stub router mode unconditionally

Choices:

  • no

  • yes

external_lsa

dictionary

Override External LSA metric in stub router mode

metric

integer

Metric to use while in stub router mode

set

boolean

Set external lsa

Choices:

  • no

  • yes

include_stub

boolean

Set maximum metric for stub links in stub router mode

Choices:

  • no

  • yes

on_proc_migration

integer

Enter stub router mode on ospfv3 process migration

on_proc_restart

integer

Enter stub router mode on ospfv3 process restart

on_startup

dictionary

Enter stub router mode on startup

time

integer

Time in seconds to stay in stub router mode

wait_for_bgp

boolean

Exit stub router mode when BGP converges

Choices:

  • no

  • yes

on_switchover

integer

Enter stub router mode on RP switchover

summary_lsa

dictionary

Override Summary LSA metric in stub router mode

metric

integer

Metric to use while in stub router mode

set

boolean

Enable summary LSA

Choices:

  • no

  • yes

summary_prefix

list / elements=dictionary

Configure IP address summaries

not_advertise

boolean

Suppress routes that match the specified prefix/mask pair

Choices:

  • no

  • yes

prefix

string / required

IP summary address/mask (A.B.C.D/prefix)

tag

integer

Set tag

timers

dictionary

Adjust routing timers

lsa_arrival

integer

Specify LSA arrival timers

pacing

dictionary

Specify pacing timers

flood

integer

Flood pacing timer

lsa_group

integer

LSA group pacing timer

retransmission

integer

LSA group pacing timer

throttle

dictionary

Adjust throttle timers

lsa

dictionary

Specify LSA throttle timers

all_lsa_initial

integer

Delay to generate first occurrence of LSA in milliseconds

all_lsa_minimum

integer

Minimum delay between originating the same LSA in milliseconds

spf

dictionary

Specify SPF throttle timers

spf_initial

integer

Delay to generate first occurrence of SPF in ms

spf_minimum

integer

Minimum delay between originating the same SPF in ms

trace

dictionary

Specify OSPF tracing options

size

string

Delete existing buffer and create one with N entries

value

integer

Specify trace entry

transmit_delay

integer

Estimated time needed to send link-state update packet

running_config

string

This option is used only with state parsed.

The value of this option should be the output received from the IOS-XR device by executing the command show running-config router ospfv3.

The state parsed reads the configuration from running_config option and transforms it into Ansible structured data as per the resource module’s argspec and the value is then returned in the parsed key within the result.

state

string

The state the configuration should be left in

Choices:

  • merged ← (default)

  • replaced

  • overridden

  • deleted

  • gathered

  • rendered

  • parsed

Notes

Note

Examples

# Using merged

# Before state:
# -------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospfv3
# Thu Jun 11 15:54:44.569 UTC
# % No such configuration item(s)
#

- name: Merge provided OSPFv3 configuration with the existing configuration
  cisco.iosxr.iosxr_ospfv3:
    config:
      processes:
        - process_id: 27
          areas:
            - area_id: 10
              hello_interval: 2
        - process_id: 26
          authentication:
            disable: true
        - process_id: 10
          areas:
            - area_id: 11
              default_cost: 5
              cost: 11
            - area_id: 22
              default_cost: 6
        - process_id: 30
          areas:
            - area_id: 11
              default_cost: 5
            - area_id: 22
              default_cost: 6
          cost: 2
          default_metric: 10
          transmit_delay: 2
          hello_interval: 1
          dead_interval: 2
          retransmit_interval: 2
          packet_size: 577
          priority: 1
          router_id: '2.2.2.2'
          demand_circuit: true
          mtu_ignore: true
    state: merged

#
#
# ------------------------
# Module Execution Result
# ------------------------
#
#  "before": {}
#
#  "commands": [
#         "router ospfv3 10",
#         "area 11 default-cost 5",
#         "area 11 cost 11",
#         "area 22 default-cost 6",
#         "router ospfv3 26",
#         "authentication disable",
#         "router ospfv3 27",
#         "area 10 hello-interval 2",
#         "router ospfv3 30",
#         "cost 2",
#         "priority 1",
#         "default-metric 10",
#         "router-id 2.2.2.2",
#         "demand-circuit",
#         "packet-size 577",
#         "transmit-delay 2",
#         "dead-interval 2",
#         "hello-interval 1",
#         "retransmit-interval 2",
#         "mtu-ignore",
#         "area 11 default-cost 5",
#         "area 22 default-cost 6"
#    ]
#
#  "after": {
#         "processes": [
#             {
#                 "areas": [
#                     {
#                         "area_id": "11",
#                         "cost": 11,
#                         "default_cost": 5
#                     },
#                     {
#                         "area_id": "22",
#                         "default_cost": 6
#                     }
#                 ],
#                 "process_id": "10"
#             },
#             {
#                 "authentication": {
#                     "disable": true
#                 },
#                 "process_id": "26"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "10",
#                         "hello_interval": 2
#                     }
#                 ],
#                 "process_id": "27"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "11",
#                         "default_cost": 5
#                     },
#                     {
#                         "area_id": "22",
#                         "default_cost": 6
#                     }
#                 ],
#                 "cost": 2,
#                 "dead_interval": 2,
#                 "default_metric": 10,
#                 "demand_circuit": true,
#                 "hello_interval": 1,
#                 "mtu_ignore": true,
#                 "packet_size": 577,
#                 "priority": 1,
#                 "process_id": "30",
#                 "retransmit_interval": 2,
#                 "router_id": "2.2.2.2",
#                 "transmit_delay": 2
#             }
#         ]
#     }
#
#
# ------------
# After state
# ------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospfv3
# router ospfv3 10
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospfv3 26
#  authentication disable
# !
# router ospfv3 27
#  area 10
#   hello-interval 2
#  !
#  area 20
#  !
#  area 30
#  !
# !
# router ospfv3 30
#  cost 2
#  priority 1
#  mtu-ignore
#  packet-size 577
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit
#  hello-interval 1
#  transmit-delay 2
#  router-id 2.2.2.2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# router ospfv3 10
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospfv3 26
#  authentication disable
# !
# router ospfv3 27
#  area 10
#   hello-interval 2
#  !
#  area 20
#  !
#  area 30
#  !
# !
# router ospfv3 30
#  cost 2
#  priority 1
#  mtu-ignore
#  packet-size 577
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit
#  hello-interval 1
#  transmit-delay 2
#  router-id 2.2.2.2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !



# Using replaced
#
# ------------
# Before state
# ------------
#
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# router ospfv3 10
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospfv3 26
#  authentication disable
# !
# router ospfv3 27
#  area 10
#   hello-interval 2
#  !
#  area 20
#  !
#  area 30
#  !
# !
# router ospfv3 30
#  cost 2
#  priority 1
#  mtu-ignore
#  packet-size 577
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit
#  hello-interval 1
#  transmit-delay 2
#  router-id 2.2.2.2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# router ospfv3 10
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospfv3 26
#  authentication disable
# !
# router ospfv3 27
#  area 10
#   hello-interval 2
#  !
#  area 20
#  !
#  area 30
#  !
# !
# router ospfv3 30
#  cost 2
#  priority 1
#  mtu-ignore
#  packet-size 577
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit
#  hello-interval 1
#  transmit-delay 2
#  router-id 2.2.2.2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !

- name: Replace OSPFv3 routes configurations from the device
  cisco.iosxr.iosxr_ospfv3:
    config:
      processes:
        - process_id: 27
          areas:
            - area_id: 10
              hello_interval: 2
            - area_id: 20
              cost: 2
              default_cost: 2
        - process_id: 26
          authentication:
            disable: true
    state: replaced

#
#
# ------------------------
# Module Execution Result
# ------------------------
#
#  "before": {
#         "processes": [
#             {
#                 "areas": [
#                     {
#                         "area_id": "11",
#                         "cost": 11,
#                         "default_cost": 5
#                     },
#                     {
#                         "area_id": "22",
#                         "default_cost": 6
#                     }
#                 ],
#                 "process_id": "10"
#             },
#             {
#                 "authentication": {
#                     "disable": true
#                 },
#                 "process_id": "26"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "10",
#                         "hello_interval": 2
#                     }
#                 ],
#                 "process_id": "27"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "11",
#                         "default_cost": 5
#                     },
#                     {
#                         "area_id": "22",
#                         "default_cost": 6
#                     }
#                 ],
#                 "cost": 2,
#                 "dead_interval": 2,
#                 "default_metric": 10,
#                 "demand_circuit": true,
#                 "hello_interval": 1,
#                 "mtu_ignore": true,
#                 "packet_size": 577,
#                 "priority": 1,
#                 "process_id": "30",
#                 "retransmit_interval": 2,
#                 "router_id": "2.2.2.2",
#                 "transmit_delay": 2
#             }
#         ]
#     }
#
#  "commands": [
#         "router ospfv3 27",
#         "area 20 default-cost 2",
#         "area 20 cost 2"
#     ]
#
#  "after": {
#         "processes": [
#             {
#                 "areas": [
#                     {
#                         "area_id": "11",
#                         "cost": 11,
#                         "default_cost": 5
#                     },
#                     {
#                         "area_id": "22",
#                         "default_cost": 6
#                     }
#                 ],
#                 "process_id": "10"
#             },
#             {
#                 "authentication": {
#                     "disable": true
#                 },
#                 "process_id": "26"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "10",
#                         "hello_interval": 2
#                     },
#                     {
#                         "area_id": "20",
#                         "cost": 2,
#                         "default_cost": 2
#                     }
#                 ],
#                 "process_id": "27"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "11",
#                         "default_cost": 5
#                     },
#                     {
#                         "area_id": "22",
#                         "default_cost": 6
#                     }
#                 ],
#                 "cost": 2,
#                 "dead_interval": 2,
#                 "default_metric": 10,
#                 "demand_circuit": true,
#                 "hello_interval": 1,
#                 "mtu_ignore": true,
#                 "packet_size": 577,
#                 "priority": 1,
#                 "process_id": "30",
#                 "retransmit_interval": 2,
#                 "router_id": "2.2.2.2",
#                 "transmit_delay": 2
#             }
#         ]
#     }
#
#
# -----------
# After state
# -----------
#
# RP/0/RP0/CPU0:anton(config)#do show running-config router ospfv3
# router ospfv3 10
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospfv3 26
#  authentication disable
# !
# router ospfv3 27
#  area 10
#   hello-interval 2
#  !
#  area 20
#   cost 2
#   default-cost 2
#  !
#  area 30
#  !
# !
# router ospfv3 30
#  cost 2
#  priority 1
#  mtu-ignore
#  packet-size 577
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit
#  hello-interval 1
#  transmit-delay 2
#  router-id 2.2.2.2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !


- name: Override existing OSPFv3 configurations from the device
  cisco.iosxr.iosxr_ospfv3:
    config:
      processes:
        - process_id: 27
          areas:
            - area_id: 10
              hello_interval: 2
              authentication:
                disable: true
            - area_id: 20
              cost: 2
              default_cost: 2
              authentication:
                disable: true
        - process_id: 26
          areas:
            - area_id: 10
              hello_interval: 2
              authentication:
                disable: true
    state: overridden

#
#
# ------------------------
# Module Execution Result
# ------------------------
#
#  "before": {
#         "processes": [
#             {
#                 "areas": [
#                     {
#                         "area_id": "11",
#                         "cost": 11,
#                         "default_cost": 5
#                     },
#                     {
#                         "area_id": "22",
#                         "default_cost": 6
#                     }
#                 ],
#                 "process_id": "10"
#             },
#             {
#                 "authentication": {
#                     "disable": true
#                 },
#                 "process_id": "26"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "10",
#                         "hello_interval": 2
#                     },
#                     {
#                         "area_id": "20",
#                         "cost": 2,
#                         "default_cost": 2
#                     }
#                 ],
#                 "process_id": "27"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "11",
#                         "default_cost": 5
#                     },
#                     {
#                         "area_id": "22",
#                         "default_cost": 6
#                     }
#                 ],
#                 "cost": 2,
#                 "dead_interval": 2,
#                 "default_metric": 10,
#                 "demand_circuit": true,
#                 "hello_interval": 1,
#                 "mtu_ignore": true,
#                 "packet_size": 577,
#                 "priority": 1,
#                 "process_id": "30",
#                 "retransmit_interval": 2,
#                 "router_id": "2.2.2.2",
#                 "transmit_delay": 2
#             }
#         ]
#     }
#
#  "commands": [
#         "router ospfv3 10",
#         "no area 11 default-cost 5",
#         "no area 11 cost 11",
#         "no area 22 default-cost 6",
#         "router ospfv3 30",
#         "no cost 2",
#         "no priority 1",
#         "no default-metric 10",
#         "no router-id 2.2.2.2",
#         "no demand-circuit",
#         "no packet-size 577",
#         "no transmit-delay 2",
#         "no dead-interval 2",
#         "no hello-interval 1",
#         "no retransmit-interval 2",
#         "no mtu-ignore",
#         "no area 11 default-cost 5",
#         "no area 22 default-cost 6",
#         "router ospfv3 26",
#         "area 10 hello-interval 4"
#     ]
#
#  "after": {
#         "processes": [
#             {
#                 "process_id": "10"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "10",
#                         "hello_interval": 4
#                     }
#                 ],
#                 "authentication": {
#                     "disable": true
#                 },
#                 "process_id": "26"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "10",
#                         "hello_interval": 2
#                     },
#                     {
#                         "area_id": "20",
#                         "cost": 2,
#                         "default_cost": 2
#                     }
#                 ],
#                 "process_id": "27"
#             },
#             {
#                 "process_id": "30"
#             }
#         ]
#     }
#
#
# -----------
# After state
# -----------
#
# RP/0/RP0/CPU0:anton#show running-config router ospfv3
# router ospfv3 10
#  area 11
#  !
#  area 22
#  !
# !
# router ospfv3 26
#  authentication disable
#  area 10
#   hello-interval 4
#  !
# !
# router ospfv3 27
#  area 10
#   hello-interval 2
#  !
#  area 20
#   cost 2
#   default-cost 2
#  !
#  area 30
#  !
# !
# router ospfv3 30
#  area 11
#  !
#  area 22
#  !
# !



# Using deleted
#
# ------------
# Before state
# ------------
#
#
# RP/0/RP0/CPU0:anton#show running-config router ospfv3
# router ospfv3 10
#  area 11
#  !
#  area 22
#  !
# !
# router ospfv3 26
#  authentication disable
#  area 10
#   hello-interval 4
#  !
# !
# router ospfv3 27
#  area 10
#   hello-interval 2
#  !
#  area 20
#   cost 2
#   default-cost 2
#  !
#  area 30
#  !
# !
# router ospfv3 30
#  area 11
#  !
#  area 22
#  !
# !

- name: Deleted existing OSPFv3 configurations from the device
  cisco.iosxr.iosxr_ospfv3:
    config:
      processes:
      - process_id: '10'
      - process_id: '26'
      - process_id: '27'
      - process_id: '30'
    state: deleted

#
#
# ------------------------
# Module Execution Result
# ------------------------
#
#  "before": {
#         "processes": [
#             {
#                 "process_id": "10"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "10",
#                         "hello_interval": 4
#                     }
#                 ],
#                 "authentication": {
#                     "disable": true
#                 },
#                 "process_id": "26"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "10",
#                         "hello_interval": 2
#                     },
#                     {
#                         "area_id": "20",
#                         "cost": 2,
#                         "default_cost": 2
#                     }
#                 ],
#                 "process_id": "27"
#             },
#             {
#                 "process_id": "30"
#             }
#         ]
#     },
#
#  "commands": [
#         "router ospfv3 26",
#         "no authentication disable",
#         "no area 10 hello-interval 4",
#         "router ospfv3 27",
#         "no area 10 hello-interval 2",
#         "no area 20 default-cost 2",
#         "no area 20 cost 2"
#     ]
#
#  "after": {
#        "processes": [
#            {
#                "process_id": "10"
#            },
#            {
#                "process_id": "26"
#            },
#            {
#                "process_id": "27"
#            },
#            {
#                "process_id": "30"
#            }
#        ]
#    }
#
#
# -----------
# After state
# -----------
#
# RP/0/RP0/CPU0:anton(config)#show running-config router ospfv3
# router ospfv3 10
# !
# router ospfv3 26
# !
# router ospfv3 27
# !
# router ospfv3 30
# !


# Using parsed
# parsed.cfg
# ------------
# router ospfv3 10
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospfv3 26
#  authentication disable
# !
# router ospfv3 27
#  area 10
#   hello-interval 2
#  !
# !
# router ospfv3 30
#  router-id 2.2.2.2
#  cost 2
#  packet-size 577
#  priority 1
#  mtu-ignore
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
- name: Parsed the device configuration to get output commands
  cisco.iosxr.iosxr_ospfv3:
    running_config: "{{ lookup('file', './parsed.cfg') }}"
    state: parsed
#
#
# -------------------------
# Module Execution Result
# -------------------------
#
#
# "parsed": {
#         "processes": [
#             {
#                 "areas": [
#                     {
#                         "area_id": "11",
#                         "cost": 11,
#                         "default_cost": 5
#                     },
#                     {
#                         "area_id": "22",
#                         "default_cost": 6
#                     }
#                 ],
#                 "process_id": "10"
#             },
#             {
#                 "authentication": {
#                     "disable": true
#                 },
#                 "process_id": "26"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "10",
#                         "hello_interval": 2
#                     }
#                 ],
#                 "process_id": "27"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "11",
#                         "default_cost": 5
#                     },
#                     {
#                         "area_id": "22",
#                         "default_cost": 6
#                     }
#                 ],
#                 "cost": 2,
#                 "dead_interval": 2,
#                 "default_metric": 10,
#                 "demand_circuit": true,
#                 "hello_interval": 1,
#                 "mtu_ignore": true,
#                 "packet_size": 577,
#                 "priority": 1,
#                 "process_id": "30",
#                 "retransmit_interval": 2,
#                 "router_id": "2.2.2.2",
#                 "transmit_delay": 2
#             }
#         ]
#     }
#
# Using rendered
#
#
- name: Render the commands for provided  configuration
  cisco.iosxr.iosxr_ospfv3:
    config:
      processes:
        - process_id: 27
          areas:
            - area_id: 10
              hello_interval: 2
        - process_id: 26
          authentication:
            disable: true
        - process_id: 10
          areas:
            - area_id: 11
              default_cost: 5
              cost: 11
            - area_id: 22
              default_cost: 6
        - process_id: 30
          areas:
            - area_id: 11
              default_cost: 5
            - area_id: 22
              default_cost: 6
          cost: 2
          default_metric: 10
          transmit_delay: 2
          hello_interval: 1
          dead_interval: 2
          retransmit_interval: 2
          packet_size: 577
          priority: 1
          router_id: '2.2.2.2'
          demand_circuit: true
          mtu_ignore: true
    state: rendered

#
#
# -------------------------
# Module Execution Result
# -------------------------
#
#
# "rendered": [
#         "router ospfv3 27",
#         "area 10 hello-interval 2",
#         "router ospfv3 26",
#         "authentication disable",
#         "router ospfv3 10",
#         "area 11 default-cost 5",
#         "area 11 cost 11",
#         "area 22 default-cost 6",
#         "router ospfv3 30",
#         "cost 2",
#         "priority 1",
#         "default-metric 10",
#         "router-id 2.2.2.2",
#         "demand-circuit",
#         "packet-size 577",
#         "transmit-delay 2",
#         "dead-interval 2",
#         "hello-interval 1",
#         "retransmit-interval 2",
#         "mtu-ignore",
#         "area 11 default-cost 5",
#         "area 22 default-cost 6"
#     ]


# Using gathered
#
# Before state:
# -------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# router ospfv3 10
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospfv3 26
#  authentication disable
#  area 10
#  !
# !
# router ospfv3 27
#  area 10
#   hello-interval 2
#  !
#  area 20
#  !
#  area 30
#  !
# !
# router ospfv3 30
#  cost 2
#  priority 1
#  mtu-ignore
#  packet-size 577
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit
#  hello-interval 1
#  transmit-delay 2
#  router-id 2.2.2.2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !

- name: Gather ospfv3 routes configuration
  cisco.iosxr.iosxr_ospfv3:
    state: gathered
#
#
# -------------------------
# Module Execution Result
# -------------------------
#
#    "gathered": {
#         "processes": [
#             {
#                 "areas": [
#                     {
#                         "area_id": "11",
#                         "cost": 11,
#                         "default_cost": 5
#                     },
#                     {
#                         "area_id": "22",
#                         "default_cost": 6
#                     }
#                 ],
#                 "process_id": "10"
#             },
#             {
#                 "authentication": {
#                     "disable": true
#                 },
#                 "process_id": "26"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "10",
#                         "hello_interval": 2
#                     }
#                 ],
#                 "process_id": "27"
#             },
#             {
#                 "areas": [
#                     {
#                         "area_id": "11",
#                         "default_cost": 5
#                     },
#                     {
#                         "area_id": "22",
#                         "default_cost": 6
#                     }
#                 ],
#                 "cost": 2,
#                 "dead_interval": 2,
#                 "default_metric": 10,
#                 "demand_circuit": true,
#                 "hello_interval": 1,
#                 "mtu_ignore": true,
#                 "packet_size": 577,
#                 "priority": 1,
#                 "process_id": "30",
#                 "retransmit_interval": 2,
#                 "router_id": "2.2.2.2",
#                 "transmit_delay": 2
#             }
#         ]
#     }
#

Authors

  • Rohit Thakur (@rohitthakur2590)