You are reading an unmaintained version of the Ansible documentation. Unmaintained Ansible versions can contain unfixed security vulnerabilities (CVE). Please upgrade to a maintained version. See the latest Ansible documentation.

cisco.nxos.nxos_igmp_interface module – Manages IGMP interface configuration.

Note

This module is part of the cisco.nxos collection (version 2.9.1).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install cisco.nxos.

To use it in a playbook, specify: cisco.nxos.nxos_igmp_interface.

New in version 1.0.0: of cisco.nxos

Synopsis
Parameters
Notes
Examples
Return Values

Synopsis 

Manages IGMP interface configuration settings.

Note

This module has a corresponding action plugin.

Parameters 

Parameter	Comments
group_timeout string	Sets the group membership timeout for IGMPv2. Values can range from 3 to 65,535 seconds or keyword ‘default’. The default is 260 seconds.
immediate_leave boolean	Enables the device to remove the group entry from the multicast routing table immediately upon receiving a leave message for the group. Use this command to minimize the leave latency of IGMPv2 group memberships on a given IGMP interface because the device does not send group-specific queries. The default is disabled. Choices: no yes
interface string / required	The full interface name for IGMP configuration. e.g. Ethernet1/2.
last_member_qrt string	Sets the query interval waited after sending membership reports before the software deletes the group state. Values can range from 1 to 25 seconds or keyword ‘default’. The default is 1 second.
last_member_query_count string	Sets the number of times that the software sends an IGMP query in response to a host leave message. Values can range from 1 to 5 or keyword ‘default’. The default is 2.
oif_ps raw	Configure prefixes and sources for static outgoing interface (OIF). This is a list of dict where each dict has source and prefix defined or just prefix if source is not needed. The specified values will be configured on the device and if any previous prefix/sources exist, they will be removed. Keyword ‘default’ is also accepted which removes all existing prefix/sources.
oif_routemap string	Configure a routemap for static outgoing interface (OIF) or keyword ‘default’.
provider dictionary	Deprecated Starting with Ansible 2.5 we recommend using `connection: network_cli`. Starting with Ansible 2.6 we recommend using `connection: httpapi` for NX-API. This option will be removed in a release after 2022-06-01. For more information please see the https://docs.ansible.com/ansible/latest/network/user_guide/platform_nxos.html. A dict object containing connection details.
auth_pass string	Specifies the password to use if required to enter privileged mode on the remote device. If authorize is false, then this argument does nothing. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_AUTH_PASS` will be used instead.
authorize boolean	Instructs the module to enter privileged mode on the remote device before sending any commands. If not specified, the device will attempt to execute all commands in non-privileged mode. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_AUTHORIZE` will be used instead. Choices: no ← (default) yes
host string	Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
password string	Specifies the password to use to authenticate the connection to the remote device. This is a common argument used for either cli or nxapi transports. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_PASSWORD` will be used instead.
port integer	Specifies the port to use when building the connection to the remote device. This value applies to either cli or nxapi. The port value will default to the appropriate transport common port if none is provided in the task. (cli=22, http=80, https=443).
ssh_keyfile string	Specifies the SSH key to use to authenticate the connection to the remote device. This argument is only used for the cli transport. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_SSH_KEYFILE` will be used instead.
timeout integer	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error. NX-API can be slow to return on long-running commands (sh mac, sh bgp, etc).
transport string	Configures the transport connection to use when connecting to the remote device. The transport argument supports connectivity to the device over cli (ssh) or nxapi. Choices: cli ← (default) nxapi
use_proxy boolean	If `no`, the environment variables `http_proxy` and `https_proxy` will be ignored. Choices: no yes ← (default)
use_ssl boolean	Configures the transport to use SSL if set to `yes` only when the `transport=nxapi`, otherwise this value is ignored. Choices: no ← (default) yes
username string	Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate either the CLI login or the nxapi authentication depending on which transport is used. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_USERNAME` will be used instead.
validate_certs boolean	If `no`, SSL certificates will not be validated. This should only be used on personally controlled sites using self-signed certificates. If the transport argument is not nxapi, this value is ignored. Choices: no ← (default) yes
querier_timeout string	Sets the querier timeout that the software uses when deciding to take over as the querier. Values can range from 1 to 65535 seconds or keyword ‘default’. The default is 255 seconds.
query_interval string	Sets the frequency at which the software sends IGMP host query messages. Values can range from 1 to 18000 seconds or keyword ‘default’. The default is 125 seconds.
query_mrt string	Sets the response time advertised in IGMP queries. Values can range from 1 to 25 seconds or keyword ‘default’. The default is 10 seconds.
report_llg boolean	Configures report-link-local-groups. Enables sending reports for groups in 224.0.0.0/24. Reports are always sent for nonlink local groups. By default, reports are not sent for link local groups. Choices: no yes
restart boolean	Restart IGMP. This is NOT idempotent as this is action only. Choices: no ← (default) yes
robustness string	Sets the robustness variable. Values can range from 1 to 7 or keyword ‘default’. The default is 2.
startup_query_count string	Query count used when the IGMP process starts up. The range is from 1 to 10 or keyword ‘default’. The default is 2.
startup_query_interval string	Query interval used when the IGMP process starts up. The range is from 1 to 18000 or keyword ‘default’. The default is 31.
state string	Manages desired state of the resource. Choices: present ← (default) absent default
version string	IGMP version. It can be 2 or 3 or keyword ‘default’. Choices: 2 3 default

Notes 

Note

Tested against NXOSv 7.3.(0)D1(1) on VIRL
Unsupported for Cisco MDS
When state=default, supported params will be reset to a default state. These include version, startup_query_interval, startup_query_count, robustness, querier_timeout, query_mrt, query_interval, last_member_qrt, last_member_query_count, group_timeout, report_llg, and immediate_leave.
When state=absent, all configs for oif_ps, and oif_routemap will be removed.
PIM must be enabled to use this module.
This module is for Layer 3 interfaces.
Route-map check not performed (same as CLI) check when configuring route-map with ‘static-oif’
If restart is set to true with other params set, the restart will happen last, i.e. after the configuration takes place. However, ‘restart’ itself is not idempotent as it is an action and not configuration.
For information on using CLI and NX-API see the NXOS Platform Options guide
For more information on using Ansible to manage network devices see the Ansible Network Guide
For more information on using Ansible to manage Cisco devices see the Cisco integration page.

Examples 

- cisco.nxos.nxos_igmp_interface:
    interface: ethernet1/32
    startup_query_interval: 30
    oif_ps:
    - {prefix: 238.2.2.6}
    - {source: 192.168.0.1, prefix: 238.2.2.5}
    state: present

Return Values 

Common return values are documented here, the following are the fields unique to this module:

Key	Description
changed boolean	check to see if a change was made on the device Returned: always Sample: true
end_state dictionary	k/v pairs of igmp interface configuration after module execution Returned: always Sample: {“oif_ps”: [{“prefix”: “238.2.2.6”}, {“prefix”: “238.2.2.5”, “source”: “192.168.0.1”}], “startup_query_count”: “30”}
existing dictionary	k/v pairs of existing igmp_interface configuration Returned: always Sample: {“oif_ps”: [], “startup_query_count”: “2”}
proposed dictionary	k/v pairs of parameters passed into module Returned: always Sample: {“oif_ps”: [{“prefix”: “238.2.2.6”}, {“prefix”: “238.2.2.5”, “source”: “192.168.0.1”}], “startup_query_count”: “30”}
updates list / elements=string	commands sent to the device Returned: always Sample: [“interface Ethernet1/32”, “ip igmp startup-query-count 30”, “ip igmp static-oif 238.2.2.6”, “ip igmp static-oif 238.2.2.5 source 192.168.0.1”]

Authors

Jason Edelman (@jedelman8)
Gabriele Gerbino (@GGabriele)

Collection links

Issue Tracker Repository (Sources)

cisco.nxos.nxos_igmp_interface module – Manages IGMP interface configuration.

Synopsis

Parameters

Notes

Examples

Return Values

Authors

Collection links

Synopsis 

Parameters 

Notes 

Examples 

Return Values 