community.network.ce_is_is_interface module – Manages isis interface configuration on HUAWEI CloudEngine devices.

Note

This module is part of the community.network collection (version 3.3.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install community.network.

To use it in a playbook, specify: community.network.ce_is_is_interface.

New in version 0.2.0: of community.network

Synopsis

  • Manages isis process id, creates a isis instance id or deletes a process id on HUAWEI CloudEngine devices.

Parameters

Parameter

Comments

bfdblocken

boolean

Blocking interfaces to dynamically create BFD features. The value is a bool type.

Choices:

  • no

  • yes

bfdstaticen

boolean

Configure static BFD on a specific interface enabled with ISIS. The value is a bool type.

Choices:

  • no

  • yes

ifname

string / required

A L3 interface.

instance_id

integer / required

Specifies the id of a isis process. The value is a number of 1 to 4294967295.

level1cost

integer

Specifies the link cost of the interface when performing Level-1 SPF calculation. The value is a number of 0 to 16777215.

level1dispriority

integer

the dispriority of the level1. The value is a number of 1 to 127.

level2cost

integer

Specifies the link cost of the interface when performing Level-2 SPF calculation. The value is a number of 0 to 16777215.

level2dispriority

integer

the dispriority of the level1. The value is a number of 1 to 127.

leveltype

string

level type for three types.

Choices:

  • level_1

  • level_2

  • level_1_2

p2pnegotiationmode

string

Set the P2P neighbor negotiation type.

Choices:

  • 2_way

  • 3_way

  • 3_wayonly

p2ppeeripignore

boolean

When the P2P hello packet is received, no IP address check is performed. The value is a bool type.

Choices:

  • no

  • yes

ppposicpcheckenable

boolean

Interface for setting PPP link protocol to check OSICP negotiation status. The value is a bool type.

Choices:

  • no

  • yes

silentcost

boolean

Specifies whether the routing cost of the silent interface is 0. The value is a bool type.

Choices:

  • no

  • yes

silentenable

boolean

enable the interface can send isis message. The value is a bool type.

Choices:

  • no

  • yes

snpacheck

boolean

Enable SNPA check for LSPs and SNPs. The value is a bool type.

Choices:

  • no

  • yes

state

string

Determines whether the config should be present or not on the device.

Choices:

  • present ← (default)

  • absent

typep2penable

boolean

Simulate the network type of the interface as P2P. The value is a bool type.

Choices:

  • no

  • yes

Notes

Note

  • Interface must already be a L3 port when using this module.

  • This module requires the netconf system service be enabled on the remote device being managed.

  • This module works with connection netconf.

Examples

- name: "create vlan and config vlanif"
  ce_config:
    lines: 'vlan {{ test_vlan_id }},quit,interface {{test_intf_vlanif}},ip address {{test_vlanif_ip}} 24'
    match: none

- name: "create eth-trunk and config eth-trunk"
  ce_config:
    lines: 'interface {{test_intf_trunk}},undo portswitch,ip address {{test_trunk_ip}} 24'
    match: none

- name: "create vpn instance"
  ce_config:
    lines: 'ip vpn-instance {{test_vpn}},ipv4-family'
    match: none

- name: Set isis circuit-level
  community.network.ce_is_is_interface:
    instance_id: 3
    ifname: Eth-Trunk10
    leveltype: level_1_2
    state: present

- name: Set isis level1dispriority
  community.network.ce_is_is_interface:
    instance_id: 3
    ifname: Eth-Trunk10
    level1dispriority: 0
    state: present

- name: Set isis level2dispriority
  community.network.ce_is_is_interface:
    instance_id: 3
    ifname: Eth-Trunk10
    level2dispriority: 0
    state: present

- name: Set isis silentenable
  community.network.ce_is_is_interface:
    instance_id: 3
    ifname: Eth-Trunk10
    silentenable: true
    state: present

- name: Set vpn name
  ce_is_is_instance:
    instance_id: 22
    vpn_name: vpn1
    state: present

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key

Description

changed

boolean

check to see if a change was made on the device

Returned: always

Sample: true

end_state

dictionary

k/v pairs of configuration after module execution

Returned: always

Sample: {“session”: {“addrType”: “IPV4”, “createType”: “SESS_STATIC”, “destAddr”: null, “outIfName”: “10GE1/0/1”, “sessName”: “bfd_l2link”, “srcAddr”: null, “useDefaultIp”: “true”, “vrfName”: null}}

existing

dictionary

k/v pairs of existing configuration

Returned: always

Sample: {“session”: {}}

proposed

dictionary

k/v pairs of parameters passed into module

Returned: always

Sample: {“addr_type”: null, “create_type”: null, “dest_addr”: null, “out_if_name”: “10GE1/0/1”, “session_name”: “bfd_l2link”, “src_addr”: null, “state”: “present”, “use_default_ip”: true, “vrf_name”: null}

updates

list / elements=string

commands sent to the device

Returned: always

Sample: [“bfd bfd_l2link bind peer-ip default-ip interface 10ge1/0/1”]

Authors

  • xuxiaowei0512 (@CloudEngine-Ansible)