cisco.nxos.nxos_ospfv3 module – OSPFv3 resource module
Note
This module is part of the cisco.nxos collection (version 3.2.0).
You might already have this collection installed if you are using the ansible
package.
It is not included in ansible-core
.
To check whether it is installed, run ansible-galaxy collection list
.
To install it, use: ansible-galaxy collection install cisco.nxos
.
To use it in a playbook, specify: cisco.nxos.nxos_ospfv3
.
New in cisco.nxos 1.2.0
Synopsis
This module manages OSPFv3 configuration on devices running Cisco NX-OS.
Note
This module has a corresponding action plugin.
Parameters
Parameter |
Comments |
---|---|
A list of OSPFv3 process configuration. |
|
A list of OSPFv3 instances’ configurations. |
|
IPv6 unicast address-family OSPFv3 settings. |
|
Configure OSPFv3 settings under IPv6 address-family. Choices:
|
|
Configure properties of OSPF Areas under address-family. |
|
The Area ID in IP Address format. |
|
Specify the default cost. |
|
Filter prefixes between OSPF areas. |
|
The direction to apply the route map. Choices:
|
|
The Route-map name. |
|
Configure an address range for the area. |
|
Cost to use for the range. |
|
Suppress advertising the specified range. Choices:
|
|
IP in Prefix format (x.x.x.x/len) |
|
Control distribution of default routes. |
|
Distribute a default route. |
|
Always advertise a default route. Choices:
|
|
Policy to control distribution of default routes |
|
Enable distribution of default route. Choices:
|
|
Configure the OSPF administrative distance. |
|
Maximum paths per destination. |
|
Redistribute information from another routing protocol. |
|
The identifier for the protocol specified. |
|
The name of the protocol. Choices:
|
|
The route map policy to constrain redistribution. |
|
Configure OSPFv3 settings under IPv6 unicast address-family. Choices:
|
|
Configure route summarization for redistribution. |
|
Suppress advertising the specified summary. Choices:
|
|
IPv6 prefix format ‘xxxx:xxxx/ml’, ‘xxxx:xxxx::/ml’ or ‘xxxx::xx/128’ |
|
A 32-bit tag value. |
|
Policy for filtering/modifying OSPF routes before sending them to RIB. |
|
Block the OSPF routes from being sent to RIB. Choices:
|
|
The Route Map name. |
|
Configure timer related constants. |
|
Configure throttle related constants. |
|
Set OSPF SPF timers. |
|
Initial SPF schedule delay in milliseconds. |
|
Maximum wait time between SPF calculations. |
|
Minimum hold time between SPF calculations. |
|
Configure properties of OSPF Areas. |
|
The Area ID in IP Address format. |
|
NSSA settings for the area. |
|
Originate Type-7 default LSA into NSSA area. Choices:
|
|
Do not send redistributed LSAs into NSSA area. Choices:
|
|
Do not send summary LSAs into NSSA area. Choices:
|
|
Policy to control distribution of default route. |
|
Configure area as NSSA. Choices:
|
|
Translate LSA. |
|
Translate from Type 7 to Type 5. |
|
Always translate LSAs Choices:
|
|
Never translate LSAs Choices:
|
|
Suppress forwarding address in translated LSAs. Choices:
|
|
Settings for configuring the area as a stub. |
|
Prevent ABR from sending summary LSAs into stub area. Choices:
|
|
Configure the area as a stub. Choices:
|
|
Calculate OSPF cost according to bandwidth. |
|
Reference bandwidth used to assign OSPF cost. |
|
Specify in which unit the reference bandwidth is specified. Choices:
|
|
Flush routes on a non-graceful controlled restart. Choices:
|
|
Configure graceful restart. |
|
Configure maximum interval to restart gracefully. |
|
Enable/Disable helper mode. Choices:
|
|
Enable graceful restart only for a planned restart Choices:
|
|
Enable graceful-restart. Choices:
|
|
Isolate this router from OSPF perspective. Choices:
|
|
Log changes in adjacency state. |
|
Notify all state changes. Choices:
|
|
Enable/disable logging changes in adjacency state. Choices:
|
|
Feature to limit the number of non-self-originated LSAs. |
|
Set count on how many times adjacencies can be suppressed. |
|
Set time during which all adjacencies are suppressed. |
|
Set the maximum number of non self-generated LSAs. |
|
Set number of minutes after which ignore-count is reset to zero. |
|
Threshold value (%) at which to generate a warning message. |
|
Log a warning message when limit is exceeded. Choices:
|
|
Maximize the cost metric. |
|
Router LSA configuration. |
|
External LSA configuration. |
|
Set max metric value for external LSAs. |
|
Set external-lsa attribute. Choices:
|
|
Inter-area-prefix LSAs configuration. |
|
Max metric value for summary LSAs. |
|
Set summary-lsa attribute. Choices:
|
|
Effective only at startup. |
|
Set on-startup attribute. Choices:
|
|
ASN of BGP to wait for. |
|
Wait period in seconds after startup. |
|
Set router-lsa attribute. Choices:
|
|
Advertise Max metric for Stub links as well. Choices:
|
|
Display OSPF router ids as DNS names. Choices:
|
|
Suppress routing updates on the interface. |
|
Interfaces passive by default. Choices:
|
|
The OSPF process tag. |
|
Set OSPF process router-id. |
|
Shutdown the OSPF protocol instance. Choices:
|
|
Configure timer related constants. |
|
Mimimum interval between arrival of a LSA. |
|
LSA group refresh/maxage interval. |
|
Configure throttle related constants. |
|
Set rate-limiting for LSA generation. |
|
The hold interval. |
|
The max interval. |
|
The start interval. |
|
Configure VRF specific OSPF settings. |
|
Configure properties of OSPF Areas. |
|
The Area ID in IP Address format. |
|
NSSA settings for the area. |
|
Originate Type-7 default LSA into NSSA area. Choices:
|
|
Do not send redistributed LSAs into NSSA area. Choices:
|
|
Do not send summary LSAs into NSSA area. Choices:
|
|
Policy to control distribution of default route. |
|
Configure area as NSSA. Choices:
|
|
Translate LSA. |
|
Translate from Type 7 to Type 5. |
|
Always translate LSAs Choices:
|
|
Never translate LSAs Choices:
|
|
Suppress forwarding address in translated LSAs. Choices:
|
|
Settings for configuring the area as a stub. |
|
Prevent ABR from sending summary LSAs into stub area. Choices:
|
|
Configure the area as a stub. Choices:
|
|
Calculate OSPF cost according to bandwidth. |
|
Reference bandwidth used to assign OSPF cost. |
|
Specify in which unit the reference bandwidth is specified. Choices:
|
|
Configure graceful restart. |
|
Configure maximum interval to restart gracefully. |
|
Enable/Disable helper mode. Choices:
|
|
Enable graceful restart only for a planned restart Choices:
|
|
Enable graceful-restart. Choices:
|
|
Log changes in adjacency state. |
|
Notify all state changes. Choices:
|
|
Enable/disable logging changes in adjacency state. Choices:
|
|
Feature to limit the number of non-self-originated LSAs. |
|
Set count on how many times adjacencies can be suppressed. |
|
Set time during which all adjacencies are suppressed. |
|
Set the maximum number of non self-generated LSAs. |
|
Set number of minutes after which ignore-count is reset to zero. |
|
Threshold value (%) at which to generate a warning message. |
|
Log a warning message when limit is exceeded. Choices:
|
|
Maximize the cost metric. |
|
Router LSA configuration. |
|
External LSA configuration. |
|
Set max metric value for external LSAs. |
|
Set external-lsa attribute. Choices:
|
|
Inter-area-prefix LSAs configuration. |
|
Max metric value for summary LSAs. |
|
Set summary-lsa attribute. Choices:
|
|
Effective only at startup. |
|
Set on-startup attribute. Choices:
|
|
ASN of BGP to wait for. |
|
Wait period in seconds after startup. |
|
Set router-lsa attribute. Choices:
|
|
Advertise Max metric for Stub links as well. Choices:
|
|
Display OSPF router ids as DNS names. Choices:
|
|
Suppress routing updates on the interface. |
|
Interfaces passive by default. Choices:
|
|
Set OSPF process router-id. |
|
Shutdown the OSPF protocol instance. Choices:
|
|
Configure timer related constants. |
|
Mimimum interval between arrival of a LSA. |
|
LSA group refresh/maxage interval. |
|
Configure throttle related constants. |
|
Set rate-limiting for LSA generation. |
|
The hold interval. |
|
The max interval. |
|
The start interval. |
|
Name/Identifier of the VRF. |
|
This option is used only with state parsed. The value of this option should be the output received from the NX-OS device by executing the command show running-config | section “^router ospfv3”. The state parsed reads the configuration from |
|
The state the configuration should be left in. Choices:
|
Notes
Note
Tested against NX-OS 7.0(3)I5(1).
Unsupported for Cisco MDS
This module works with connection
network_cli
andhttpapi
.
Examples
# Using merged
# Before state:
# -------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# nxos-9k-rdo#
- name: Merge the provided configuration with the existing running configuration
cisco.nxos.nxos_ospfv3:
config:
processes:
- process_id: 100
router_id: 203.0.113.20
- process_id: 102
router_id: 198.51.100.1
address_family:
afi: ipv6
safi: unicast
areas:
- area_id: 0.0.0.100
filter_list:
- route_map: rmap_1
direction: in
- route_map: rmap_2
direction: out
ranges:
- prefix: 2001:db2::/32
not_advertise: true
- prefix: 2001:db3::/32
cost: 120
redistribute:
- protocol: eigrp
id: 120
route_map: rmap_1
- protocol: direct
route_map: ospf102-direct-connect
vrfs:
- vrf: zone1
router_id: 198.51.100.129
areas:
- area_id: 0.0.0.102
nssa:
default_information_originate: true
no_summary: true
- area_id: 0.0.0.103
nssa:
no_summary: true
translate:
type7:
always: true
- vrf: zone2
auto_cost:
reference_bandwidth: 45
unit: Gbps
state: merged
# Task output
# -------------
# before: {}
#
# commands:
# - router ospf 102
# - router-id 198.51.100.1
# - address-family ipv6 unicast
# - redistribute eigrp 120 route-map rmap_1
# - redistribute direct route-map ospf102-direct-connect
# - area 0.0.0.100 filter-list route-map rmap_1 in
# - area 0.0.0.100 filter-list route-map rmap_2 out
# - area 0.0.0.100 range 2001:db2::/32 not-advertise
# - area 0.0.0.100 range 2001:db3::/32 cost 120
# - vrf zone1
# - router-id 198.51.100.129
# - area 0.0.0.102 nssa no-summary default-information-originate
# - area 0.0.0.103 nssa no-summary
# - area 0.0.0.103 nssa translate type7 always
# - vrf zone2
# - auto-cost reference-bandwidth 45 Gbps
# - router ospf 100
# - router-id 203.0.113.20
#
# after:
# processes:
# - process_id: "100"
# router_id: 203.0.113.20
# - address_family:
# afi: ipv4
# safi: unicast
# areas:
# - area_id: 0.0.0.100
# filter_list:
# - direction: out
# route_map: rmap_2
# - direction: in
# route_map: rmap_1
# ranges:
# - not_advertise: true
# prefix: 2001:db2::/32
# - cost: 120
# prefix: 2001:db3::/32
# redistribute:
# - protocol: direct
# route_map: ospf102-direct-connect
# - id: "120"
# protocol: eigrp
# route_map: rmap_1
# process_id: "102"
# router_id: 198.51.100.1
# vrfs:
# - areas:
# - area_id: 0.0.0.102
# nssa:
# default_information_originate: true
# no_summary: true
# - area_id: 0.0.0.103
# nssa:
# no_summary: true
# translate:
# type7:
# always: true
# router_id: 198.51.100.129
# vrf: zone1
# - auto_cost:
# reference_bandwidth: 45
# unit: Gbps
# vrf: zone2
#
# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
# router-id 203.0.113.20
# router ospfv3 102
# router-id 198.51.100.1
# address-family ipv6 unicast
# redistribute direct route-map ospf102-direct-connect
# redistribute eigrp 120 route-map rmap_1
# area 0.0.0.100 filter-list route-map rmap_2 out
# area 0.0.0.100 filter-list route-map rmap_1 in
# area 0.0.0.100 range 2001:db2::/32 not-advertise
# area 0.0.0.100 range 2001:db3::/32 cost 120
# vrf zone1
# router-id 198.51.100.129
# area 0.0.0.102 nssa no-summary default-information-originate
# area 0.0.0.103 nssa no-summary
# area 0.0.0.103 nssa translate type7 always
# vrf zone2
# auto-cost reference-bandwidth 45 Gbps
# Using replaced
# Before state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
# router-id 203.0.113.20
# router ospfv3 102
# router-id 198.51.100.1
# address-family upv6 unicast
# redistribute direct route-map ospf102-direct-connect
# redistribute eigrp 120 route-map rmap_1
# area 0.0.0.100 filter-list route-map rmap_2 out
# area 0.0.0.100 filter-list route-map rmap_1 in
# area 0.0.0.100 range 2001:db2::/32 not-advertise
# area 0.0.0.100 range 2001:db3::/32 cost 120
# vrf zone1
# router-id 198.51.100.129
# area 0.0.0.102 nssa no-summary default-information-originate
# area 0.0.0.103 nssa no-summary
# area 0.0.0.103 nssa translate type7 always
# vrf zone2
# auto-cost reference-bandwidth 45 Gbps
- name: Replace device configurations of listed OSPFv3 processes with provided configurations
cisco.nxos.nxos_ospfv3:
config:
processes:
- process_id: 102
router_id: 198.51.100.1
address_family:
afi: ipv6
safi: unicast
areas:
- area_id: 0.0.0.100
filter_list:
- route_map: rmap_8
direction: in
ranges:
- not_advertise: true
prefix: 2001:db2::/32
redistribute:
- protocol: eigrp
id: 130
route_map: rmap_1
- protocol: direct
route_map: ospf102-direct-connect
vrfs:
- vrf: zone1
router_id: 198.51.100.129
areas:
- area_id: 0.0.0.102
nssa:
default_information_originate: True
no_summary: True
state: replaced
# Task output
# -------------
# before:
# processes:
# - process_id: "100"
# router_id: 203.0.113.20
# - address_family:
# afi: ipv4
# safi: unicast
# areas:
# - area_id: 0.0.0.100
# filter_list:
# - direction: out
# route_map: rmap_2
# - direction: in
# route_map: rmap_1
# ranges:
# - not_advertise: true
# prefix: 2001:db2::/32
# - cost: 120
# prefix: 2001:db3::/32
# redistribute:
# - protocol: direct
# route_map: ospf102-direct-connect
# - id: "120"
# protocol: eigrp
# route_map: rmap_1
# process_id: "102"
# router_id: 198.51.100.1
# vrfs:
# - areas:
# - area_id: 0.0.0.102
# nssa:
# default_information_originate: true
# no_summary: true
# - area_id: 0.0.0.103
# nssa:
# no_summary: true
# translate:
# type7:
# always: true
# router_id: 198.51.100.129
# vrf: zone1
# - auto_cost:
# reference_bandwidth: 45
# unit: Gbps
# vrf: zone2
#
# commands:
# - router ospf 102
# - address-family ipv6 unicast
# - redistribute eigrp 130 route-map rmap_1
# - no redistribute eigrp 120 route-map rmap_1
# - area 0.0.0.100 filter-list route-map rmap_8 in
# - no area 0.0.0.100 filter-list route-map rmap_2 out
# - no area 0.0.0.100 range 2001:db3::/32
# - vrf zone1
# - no area 0.0.0.103 nssa
# - no area 0.0.0.103 nssa translate type7 always
# - no vrf zone2
#
# after:
# processes:
# - process_id: "100"
# router_id: 203.0.113.20
# - address_family:
# afi: ipv6
# safi: unicast
# areas:
# - area_id: 0.0.0.100
# filter_list:
# - direction: in
# route_map: rmap_8
# ranges:
# - not_advertise: true
# prefix: 2001:db2::/32
# redistribute:
# - protocol: direct
# route_map: ospf102-direct-connect
# - id: "130"
# protocol: eigrp
# route_map: rmap_1
# process_id: "102"
# router_id: 198.51.100.1
# vrfs:
# - areas:
# - area_id: 0.0.0.102
# nssa:
# default_information_originate: true
# no_summary: true
# router_id: 198.51.100.129
# vrf: zone1
# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
# router-id 203.0.113.20
# router ospfv3 102
# router-id 198.51.100.1
# address-family ipv6 unicast
# redistribute direct route-map ospf102-direct-connect
# redistribute eigrp 130 route-map rmap_1
# area 0.0.0.100 filter-list route-map rmap_8 in
# area 0.0.0.100 range 198.51.100.64/27 not-advertise
# vrf zone1
# router-id 198.51.100.129
# area 0.0.0.102 nssa no-summary default-information-originate
# Using overridden
# Before state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
# router-id 203.0.113.20
# router ospfv3 102
# router-id 198.51.100.1
# address-family ipv6 unicast
# redistribute direct route-map ospf102-direct-connect
# redistribute eigrp 120 route-map rmap_1
# area 0.0.0.100 filter-list route-map rmap_2 out
# area 0.0.0.100 filter-list route-map rmap_1 in
# area 0.0.0.100 range 2001:db2::/32 not-advertise
# area 0.0.0.100 range 2001:db3::/32 cost 120
# vrf zone1
# router-id 198.51.100.129
# area 0.0.0.102 nssa no-summary default-information-originate
# area 0.0.0.103 nssa no-summary
# area 0.0.0.103 nssa translate type7 always
# vrf zone2
# auto-cost reference-bandwidth 45 Gbps
- name: Override all OSPFv3 configuration with provided configuration
cisco.nxos.nxos_ospfv3:
config:
processes:
- process_id: 104
router_id: 203.0.113.20
- process_id: 102
router_id: 198.51.100.1
shutdown: true
state: overridden
# Task output
# -------------
# before:
# processes:
# - process_id: "100"
# router_id: 203.0.113.20
# - address_family:
# afi: ipv4
# safi: unicast
# areas:
# - area_id: 0.0.0.100
# filter_list:
# - direction: out
# route_map: rmap_2
# - direction: in
# route_map: rmap_1
# ranges:
# - not_advertise: true
# prefix: 2001:db2::/32
# - cost: 120
# prefix: 2001:db3::/32
# redistribute:
# - protocol: direct
# route_map: ospf102-direct-connect
# - id: "120"
# protocol: eigrp
# route_map: rmap_1
# process_id: "102"
# router_id: 198.51.100.1
# vrfs:
# - areas:
# - area_id: 0.0.0.102
# nssa:
# default_information_originate: true
# no_summary: true
# - area_id: 0.0.0.103
# nssa:
# no_summary: true
# translate:
# type7:
# always: true
# router_id: 198.51.100.129
# vrf: zone1
# - auto_cost:
# reference_bandwidth: 45
# unit: Gbps
# vrf: zone2
#
# commands:
# - no router ospfv3 100
# - router ospfv3 104
# - router-id 203.0.113.20
# - router ospfv3 102
# - shutdown
# - address-family ipv6 unicast
# - no redistribute direct route-map ospf102-direct-connect
# - no redistribute eigrp 120 route-map rmap_1
# - no area 0.0.0.100 filter-list route-map rmap_2 out
# - no area 0.0.0.100 filter-list route-map rmap_1 in
# - no area 0.0.0.100 range 2001:db2::/32
# - no area 0.0.0.100 range 2001:db3::/32
# - no vrf zone1
# - no vrf zone2
#
# after:
# processes:
# - process_id: "102"
# router_id: 198.51.100.1
# shutdown: true
# address_family:
# afi: ipv6
# safi: unicast
# - process_id: "104"
# router_id: 203.0.113.20
# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 102
# router-id 198.51.100.1
# address-family ipv6 unicast
# shutdown
# router ospfv3 104
# router-id 203.0.113.20
# Using deleted to delete a single OSPF process
# Before state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospf .*"
# router ospfv3 100
# router-id 203.0.113.20
# router ospfv3 102
# router-id 198.51.100.1
# address-family ipv6 unicast
# redistribute direct route-map ospf102-direct-connect
# redistribute eigrp 120 route-map rmap_1
# area 0.0.0.100 filter-list route-map rmap_2 out
# area 0.0.0.100 filter-list route-map rmap_1 in
# area 0.0.0.100 range 2001:db2::/32 not-advertise
# area 0.0.0.100 range 2001:db3::/32 cost 120
# vrf zone1
# router-id 198.51.100.129
# area 0.0.0.102 nssa no-summary default-information-originate
# area 0.0.0.103 nssa no-summary
# area 0.0.0.103 nssa translate type7 always
# vrf zone2
# auto-cost reference-bandwidth 45 Gbps
- name: Delete a single OSPFv3 process
cisco.nxos.nxos_ospfv3:
config:
processes:
- process_id: 102
state: deleted
# Task output
# -------------
# before:
# processes:
# - process_id: "100"
# router_id: 203.0.113.20
# - address_family:
# afi: ipv4
# safi: unicast
# areas:
# - area_id: 0.0.0.100
# filter_list:
# - direction: out
# route_map: rmap_2
# - direction: in
# route_map: rmap_1
# ranges:
# - not_advertise: true
# prefix: 2001:db2::/32
# - cost: 120
# prefix: 2001:db3::/32
# redistribute:
# - protocol: direct
# route_map: ospf102-direct-connect
# - id: "120"
# protocol: eigrp
# route_map: rmap_1
# process_id: "102"
# router_id: 198.51.100.1
# vrfs:
# - areas:
# - area_id: 0.0.0.102
# nssa:
# default_information_originate: true
# no_summary: true
# - area_id: 0.0.0.103
# nssa:
# no_summary: true
# translate:
# type7:
# always: true
# router_id: 198.51.100.129
# vrf: zone1
# - auto_cost:
# reference_bandwidth: 45
# unit: Gbps
# vrf: zone2
#
# commands:
# - no router ospfv3 102
#
# after:
# processes:
# - process_id: "100"
# router_id: 203.0.113.20
# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
# router-id 203.0.113.20
# Using deleted all OSPFv3 processes from the device
# Before state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
# router-id 203.0.113.20
# router ospfv3 102
# router-id 198.51.100.1
# address-family ipv6 unicast
# redistribute direct route-map ospf102-direct-connect
# redistribute eigrp 120 route-map rmap_1
# area 0.0.0.100 filter-list route-map rmap_2 out
# area 0.0.0.100 filter-list route-map rmap_1 in
# area 0.0.0.100 range 2001:db2::/32 not-advertise
# area 0.0.0.100 range 2001:db3::/32 cost 120
# vrf zone1
# router-id 198.51.100.129
# area 0.0.0.102 nssa no-summary default-information-originate
# area 0.0.0.103 nssa no-summary
# area 0.0.0.103 nssa translate type7 always
# vrf zone2
# auto-cost reference-bandwidth 45 Gbps
- name: Delete all OSPFv3 processes from the device
cisco.nxos.nxos_ospfv3:
state: deleted
# Task output
# -------------
# before:
# processes:
# - process_id: "100"
# router_id: 203.0.113.20
# - address_family:
# afi: ipv4
# safi: unicast
# areas:
# - area_id: 0.0.0.100
# filter_list:
# - direction: out
# route_map: rmap_2
# - direction: in
# route_map: rmap_1
# ranges:
# - not_advertise: true
# prefix: 2001:db2::/32
# - cost: 120
# prefix: 2001:db3::/32
# redistribute:
# - protocol: direct
# route_map: ospf102-direct-connect
# - id: "120"
# protocol: eigrp
# route_map: rmap_1
# process_id: "102"
# router_id: 198.51.100.1
# vrfs:
# - areas:
# - area_id: 0.0.0.102
# nssa:
# default_information_originate: true
# no_summary: true
# - area_id: 0.0.0.103
# nssa:
# no_summary: true
# translate:
# type7:
# always: true
# router_id: 198.51.100.129
# vrf: zone1
# - auto_cost:
# reference_bandwidth: 45
# unit: Gbps
# vrf: zone2
#
# commands:
# - no router ospfv3 100
# - no router ospfv3 102
#
# after: {}
# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# nxos-9k-rdo#
# Using rendered
- name: Render platform specific configuration lines with state rendered (without connecting to the device)
cisco.nxos.nxos_ospfv3:
config:
processes:
- process_id: 100
router_id: 203.0.113.20
- process_id: 102
router_id: 198.51.100.1
address_family:
afi: ipv6
safi: unicast
areas:
- area_id: 0.0.0.100
filter_list:
- route_map: rmap_1
direction: in
- route_map: rmap_2
direction: out
ranges:
- prefix: 2001:db2::/32
not_advertise: true
- prefix: 2001:db3::/32
cost: 120
redistribute:
- protocol: eigrp
id: 120
route_map: rmap_1
- protocol: direct
route_map: ospf102-direct-connect
vrfs:
- vrf: zone1
router_id: 198.51.100.129
areas:
- area_id: 0.0.0.102
nssa:
default_information_originate: true
no_summary: true
- area_id: 0.0.0.103
nssa:
no_summary: true
translate:
type7:
always: true
- vrf: zone2
auto_cost:
reference_bandwidth: 45
unit: Gbps
state: rendered
# Task Output (redacted)
# -----------------------
# rendered:
# - router ospfv3 100
# - router-id 203.0.113.20
# - router ospfv3 102
# - router-id 198.51.100.1
# - address-family ipv6 unicast
# - redistribute eigrp 120 route-map rmap_1
# - redistribute direct route-map ospf102-direct-connect
# - area 0.0.0.100 filter-list route-map rmap_1 in
# - area 0.0.0.100 filter-list route-map rmap_2 out
# - area 0.0.0.100 range 2001:db2::/32 not-advertise
# - area 0.0.0.100 range 2001:db3::/32 cost 120
# - vrf zone1
# - router-id 198.51.100.129
# - area 0.0.0.102 nssa no-summary default-information-originate
# - area 0.0.0.103 nssa no-summary
# - area 0.0.0.103 nssa translate type7 always
# - vrf zone2
# - auto-cost reference-bandwidth 45 Gbps
# Using parsed
# parsed.cfg
# ------------
# router ospfv3 100
# router-id 192.0.100.1
# address-family ipv6 unicast
# redistribute direct route-map ospf-direct-connect
# redistribute eigrp 120 route-map rmap_1
# area 0.0.0.100 filter-list route-map rmap_2 out
# area 0.0.0.100 filter-list route-map rmap_1 in
# area 0.0.0.100 range 2001:db2::/32 not-advertise
# area 0.0.0.100 range 2001:db3::/32 cost 120
# vrf zone1
# router-id 198.51.100.129
# area 0.0.100.1 nssa no-summary no-redistribution
# router ospfv3 102
# router-id 198.54.100.1
# shutdown
- name: Parse externally provided OSPFv3 config
cisco.nxos.nxos_ospfv3:
running_config: "{{ lookup('file', 'ospfv2.cfg') }}"
state: parsed
# Task output (redacted)
# -----------------------
# parsed:
# processes:
# - process_id: "100"
# address_family:
# afi: ipv6
# safi: unicast
# areas:
# - area_id: 0.0.0.101
# nssa:
# no_redistribution: true
# no_summary: true
# - area_id: 0.0.0.102
# stub:
# no_summary: true
# filter_list:
# - direction: out
# route_map: rmap_2
# - direction: in
# route_map: rmap_1
# ranges:
# - not_advertise: true
# prefix: 192.0.2.0/24
# - cost: 120
# prefix: 192.0.3.0/24
# redistribute:
# - protocol: direct
# route_map: ospf-direct-connect
# - id: "120"
# protocol: eigrp
# route_map: rmap_1
# router_id: 192.0.100.1
# vrfs:
# - vrf: zone1
# areas:
# - area_id: 0.0.100.1
# nssa:
# no_redistribution: true
# no_summary: true
# router_id: 192.0.100.2
# - process_id: "102"
# router_id: 198.54.100.1
# shutdown: True
# Using gathered
- name: Gather OSPFv3 facts using gathered
cisco.nxos.nxos_ospfv3:
state: gathered
# Task output (redacted)
# -----------------------
# gathered:
# processes:
# - process_id: "100"
# router_id: 203.0.113.20
# - address_family:
# afi: ipv4
# safi: unicast
# areas:
# - area_id: 0.0.0.100
# filter_list:
# - direction: out
# route_map: rmap_2
# - direction: in
# route_map: rmap_1
# ranges:
# - not_advertise: true
# prefix: 2001:db2::/32
# - cost: 120
# prefix: 2001:db3::/32
# redistribute:
# - protocol: direct
# route_map: ospf102-direct-connect
# - id: "120"
# protocol: eigrp
# route_map: rmap_1
# process_id: "102"
# router_id: 198.51.100.1
# vrfs:
# - areas:
# - area_id: 0.0.0.102
# nssa:
# default_information_originate: true
# no_summary: true
# - area_id: 0.0.0.103
# nssa:
# no_summary: true
# translate:
# type7:
# always: true
# router_id: 198.51.100.129
# vrf: zone1
# - auto_cost:
# reference_bandwidth: 45
# unit: Gbps
# vrf: zone2
#
Return Values
Common return values are documented here, the following are the fields unique to this module:
Key |
Description |
---|---|
The resulting configuration model invocation. Returned: when changed Sample: |
|
The configuration prior to the model invocation. Returned: always Sample: |
|
The set of commands pushed to the remote device. Returned: always Sample: |