You are reading an unmaintained version of the Ansible documentation. Unmaintained Ansible versions can contain unfixed security vulnerabilities (CVE). Please upgrade to a maintained version. See the latest Ansible documentation.

f5networks.f5_modules.bigip_snmp_community module – Manages SNMP communities on a BIG-IP.

Note

This module is part of the f5networks.f5_modules collection (version 1.21.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install f5networks.f5_modules.

To use it in a playbook, specify: f5networks.f5_modules.bigip_snmp_community.

New in f5networks.f5_modules 1.0.0

Synopsis

• Assists in managing Simple Network Management Protocol (SNMP) communities on a BIG-IP system. Different SNMP versions are supported by this module. Note the different parameters offered by this module, as different parameters work for different versions of SNMP. This is important if you are mixing versions v2c and 3.

Parameters

Parameter	Comments
access string	Specifies the user’s access level to the MIB. When creating a new community, if this parameter is not specified, the default is ro. When ro, specifies the user can view the MIB, but cannot modify the MIB. When rw, specifies the user can view and modify the MIB. Choices: "ro" "rw" "read-only" "read-write"
community string	Specifies the community string (password) for access to the MIB. This parameter is only relevant when version is v1 or v2c. If version is something else, this parameter is ignored.
ip_version string	Specifies whether the record applies to IPv4 or IPv6 addresses. When creating a new community, if this value is not specified, the default is 4. This parameter is only relevant when version is v1 or v2c. If version is something else, this parameter is ignored. Choices: "4" "6"
name string	Name that identifies the SNMP community. When version is v1 or v2c, this parameter is required. The name public is a reserved name on the BIG-IP. This module handles that name differently than others. Functionally, you should not see a difference.
oid string	Specifies the object identifier (OID) for the record. When version is v3, this parameter is required. When version is either v1 or v2c, if this value is specified, then source must not be set to all.
partition string	Device partition to manage resources on. Default: "Common"
port integer	Specifies the port for the trap destination. This parameter is only relevant when version is v1 or v2c. If version is something else, this parameter is ignored.
provider dictionary added in f5networks.f5_modules 1.0.0	A dict object containing connection details.
auth_provider string	Configures the auth provider for to obtain authentication tokens from the remote device. This option is really used when working with BIG-IQ devices.
no_f5_teem boolean	If yes, TEEM telemetry data is not sent to F5. You may omit this option by setting the environment variable F5_TELEMETRY_OFF. Previously used variable F5_TEEM is deprecated as its name was confusing. Choices: false ← (default) true
password aliases: pass, pwd string / required	The password for the user account used to connect to the BIG-IP. You may omit this option by setting the environment variable F5_PASSWORD.
server string / required	The BIG-IP host. You may omit this option by setting the environment variable F5_SERVER.
server_port integer	The BIG-IP server port. You may omit this option by setting the environment variable F5_SERVER_PORT. Default: 443
timeout integer	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
transport string	Configures the transport connection to use when connecting to the remote device. Choices: "rest" ← (default)
user string / required	The username to connect to the BIG-IP with. This user must have administrative privileges on the device. You may omit this option by setting the environment variable F5_USER.
validate_certs boolean	If no, SSL certificates are not validated. Use this only on personally controlled sites using self-signed certificates. You may omit this option by setting the environment variable F5_VALIDATE_CERTS. Choices: false true ← (default)
snmp_auth_password string	Specifies the password for the user. When creating a new SNMP v3 community, this parameter is required. This value must be at least 8 characters long.
snmp_auth_protocol string	Specifies the authentication method for the user. When md5, specifies the system uses the MD5 algorithm to authenticate the user. When sha, specifies the secure hash algorithm (SHA) to authenticate the user. When none, specifies the user does not require authentication. When creating a new SNMP v3 community, if this parameter is not specified, the default is sha. Choices: "md5" "sha" "none"
snmp_privacy_password string	Specifies the password for the user. When creating a new SNMP v3 community, this parameter is required. This value must be at least 8 characters long.
snmp_privacy_protocol string	Specifies the encryption protocol. When aes, specifies the system encrypts the user information using AES (Advanced Encryption Standard). When des, specifies the system encrypts the user information using DES (Data Encryption Standard). When none, specifies the system does not encrypt the user information. When creating a new SNMP v3 community, if this parameter is not specified, the default is aes. Choices: "aes" "des" "none"
snmp_username string	Specifies the name of the user for whom you want to grant access to the SNMP v3 MIB. This parameter is only relevant when version is v3. If version is something else, this parameter is ignored. When creating a new SNMP v3 community, this parameter is required. This parameter cannot be changed once it has been set.
source string	Specifies the source address for access to the MIB. This parameter can accept a value of all. If this parameter is not specified, the value is all. This parameter is only relevant when version is v1 or v2c. If version is something else, this parameter is ignored. If source is set to all, it is not possible to specify an oid. This will raise an error. You should provide this parameter when state is absent, so the correct community is removed. To remove the public SNMP community that comes with a BIG-IP, this parameter should be default.
state string	When present, ensures the address list and entries exists. When absent, ensures the address list is removed. Choices: "present" ← (default) "absent"
update_password string	always allows users to update passwords. on_create only sets the password for newly created resources. Choices: "always" ← (default) "on_create"
version string	Specifies to which SNMP version the trap destination applies. Choices: "v1" "v2c" ← (default) "v3"

Notes

Note

• For more information on using Ansible to manage F5 Networks devices see https://www.ansible.com/integrations/networks/f5.

• Requires BIG-IP software version >= 12.

• The F5 modules only manipulate the running configuration of the F5 product. To ensure that BIG-IP specific configuration persists to disk, be sure to include at least one task that uses the f5networks.f5_modules.bigip_config module to save the running configuration. Refer to the module’s documentation for the correct usage of the module to save your running configuration.

Examples

- name: Create an SMNP v2c read-only community
  bigip_snmp_community:
    name: foo
    version: v2c
    source: all
    oid: .1
    access: ro
    provider:
      password: secret
      server: lb.mydomain.com
      user: admin
  delegate_to: localhost

- name: Create an SMNP v3 read-write community
  bigip_snmp_community:
    name: foo
    version: v3
    snmp_username: foo
    snmp_auth_protocol: sha
    snmp_auth_password: secret
    snmp_privacy_protocol: aes
    snmp_privacy_password: secret
    oid: .1
    access: rw
    provider:
      password: secret
      server: lb.mydomain.com
      user: admin
  delegate_to: localhost

- name: Remove the default 'public' SNMP community
  bigip_snmp_community:
    name: public
    source: default
    state: absent
    provider:
      password: secret
      server: lb.mydomain.com
      user: admin
  delegate_to: localhost

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Description
access string	The new access level for the MIB. Returned: changed Sample: "ro"
community string	The new community value. Returned: changed Sample: "community1"
ip_version string	The new IP version value. Returned: changed Sample: "0.1"
oid string	The new OID value. Returned: changed Sample: "0.1"
snmp_auth_password string	The new password of the given snmp_username. Returned: changed Sample: "secret1"
snmp_auth_protocol string	The new SNMP auth protocol. Returned: changed Sample: "sha"
snmp_privacy_password string	The new password of the given snmp_username. Returned: changed Sample: "secret2"
snmp_privacy_protocol string	The new SNMP privacy protocol. Returned: changed Sample: "aes"
snmp_username string	The new SNMP username. Returned: changed Sample: "user1"
source string	The new source address to access the MIB. Returned: changed Sample: "1.1.1.1"

Authors

• Tim Rupp (@caphrim007)

• Wojciech Wypior (@wojtek0806)

Collection links

Issue Tracker Homepage Repository (Sources)