netapp_eseries.santricity.na_santricity_mgmt_interface module – NetApp E-Series manage management interface configuration
Note
This module is part of the netapp_eseries.santricity collection (version 1.3.1).
You might already have this collection installed if you are using the ansible package.
It is not included in ansible-core.
To check whether it is installed, run ansible-galaxy collection list.
To install it, use: ansible-galaxy collection install netapp_eseries.santricity.
To use it in a playbook, specify: netapp_eseries.santricity.na_santricity_mgmt_interface.
Synopsis
Configure the E-Series management interfaces
Parameters
Parameter |
Comments |
|---|---|
The IPv4 address to assign to the interface. Should be specified in xx.xx.xx.xx form. Mutually exclusive with config_method=dhcp |
|
The password to authenticate with the SANtricity Web Services Proxy or Embedded Web Services API. |
|
The url to the SANtricity Web Services Proxy or Embedded Web Services API. |
|
The username to authenticate with the SANtricity Web Services Proxy or Embedded Web Services API. |
|
The configuration method type to use for network interface ports. dhcp is mutually exclusive with address, subnet_mask, and gateway. Choices:
|
|
The controller that owns the port you want to configure. Controller names are represented alphabetically, with the first controller as A, the second as B, and so on. Current hardware models have either 1 or 2 available controllers, but that is not a guaranteed hard limitation and could change in the future. Choices:
|
|
Primary IPv4 or IPv6 DNS server address |
|
Secondary IPv4 or IPv6 DNS server address |
|
The configuration method type to use for DNS services. dhcp is mutually exclusive with dns_address, and dns_address_backup. Choices:
|
|
The IPv4 gateway address to utilize for the interface. Should be specified in xx.xx.xx.xx form. Mutually exclusive with config_method=dhcp |
|
Primary IPv4, IPv6, or FQDN NTP server address |
|
Secondary IPv4, IPv6, or FQDN NTP server address |
|
The configuration method type to use for NTP services. disable is mutually exclusive with ntp_address and ntp_address_backup. dhcp is mutually exclusive with ntp_address and ntp_address_backup. Choices:
|
|
The ethernet port configuration to modify. The channel represents the port number left to right on the controller, beginning with 1. |
|
Enable ssh access to the controller for debug purposes. This is a controller-level setting. rlogin/telnet will be enabled for ancient equipment where ssh is not available. Choices:
|
|
The ID of the array to manage. This value must be unique for each array. Default: |
|
Enable or disable IPv4 network interface configuration. Either IPv4 or IPv6 must be enabled otherwise error will occur. Choices:
|
|
The subnet mask to utilize for the interface. Should be specified in xx.xx.xx.xx form. Mutually exclusive with config_method=dhcp |
|
Should https certificates be validated? Choices:
|
Notes
Note
Check mode is supported.
It is highly recommended to have a minimum of one up management port on each controller.
When using SANtricity Web Services Proxy, use ERROR while parsing: While parsing M() at index 47: Module name “na_santricity_storage_system” is not a FQCN to update management paths. This is required because of a known issue and will be addressed in the proxy version 4.1. After the resolution the management ports should automatically be updated.
The interface settings are applied synchronously, but changes to the interface itself (receiving a new IP address via dhcp, etc), can take seconds or minutes longer to take effect.
The E-Series Ansible modules require either an instance of the Web Services Proxy (WSP), to be available to manage the storage-system, or an E-Series storage-system that supports the Embedded Web Services API.
Embedded Web Services is currently available on the E2800, E5700, EF570, and newer hardware models.
ERROR while parsing: While parsing M() at index 1: Module name “netapp_e_storage_system” is not a FQCN may be utilized for configuring the systems managed by a WSP instance.
Examples
- name: Configure the first port on the A controller with a static IPv4 address
na_santricity_mgmt_interface:
ssid: "1"
api_url: "https://192.168.1.100:8443/devmgr/v2"
api_username: "admin"
api_password: "adminpass"
validate_certs: true
port: "1"
controller: "A"
config_method: static
address: "192.168.1.100"
subnet_mask: "255.255.255.0"
gateway: "192.168.1.1"
- name: Disable ipv4 connectivity for the second port on the B controller
na_santricity_mgmt_interface:
ssid: "1"
api_url: "https://192.168.1.100:8443/devmgr/v2"
api_username: "admin"
api_password: "adminpass"
validate_certs: true
port: "2"
controller: "B"
enable_interface: no
- name: Enable ssh access for ports one and two on controller A
na_santricity_mgmt_interface:
ssid: "1"
api_url: "https://192.168.1.100:8443/devmgr/v2"
api_username: "admin"
api_password: "adminpass"
validate_certs: true
port: "1"
controller: "A"
ssh: yes
- name: Configure static DNS settings for the first port on controller A
na_santricity_mgmt_interface:
ssid: "1"
api_url: "https://192.168.1.100:8443/devmgr/v2"
api_username: "admin"
api_password: "adminpass"
validate_certs: true
port: "1"
controller: "A"
dns_config_method: static
dns_address: "192.168.1.100"
dns_address_backup: "192.168.1.1"
Return Values
Common return values are documented here, the following are the fields unique to this module:
Key |
Description |
|---|---|
List containing available web services embedded REST API urls Returned: on success |
|
Success message Returned: on success Sample: |