You are reading an unmaintained version of the Ansible documentation. Unmaintained Ansible versions can contain unfixed security vulnerabilities (CVE). Please upgrade to a maintained version. See the latest Ansible documentation.

cisco.iosxr.iosxr_acls module – Resource module to configure ACLs.

Note

This module is part of the cisco.iosxr collection (version 5.0.3).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install cisco.iosxr.

To use it in a playbook, specify: cisco.iosxr.iosxr_acls.

New in cisco.iosxr 1.0.0

Synopsis 

This module manages Access Control Lists (ACLs) on devices running IOS-XR.

Aliases: acls

Parameters 

Parameter	Comments
config list / elements=dictionary	A list of dictionaries specifying ACL configurations.
acls list / elements=dictionary	A list of Access Control Lists (ACLs).
aces list / elements=dictionary	List of Access Control Entries (ACEs) for this Access Control List (ACL).
authen boolean	Match if authentication header is present. Choices: `false` `true`
capture boolean	Capture matched packet. Choices: `false` `true`
destination dictionary	Specifies the packet destination.
address string	The destination IP address to match.
any boolean	Match any destination address. Choices: `false` `true`
host string	The host IP address to match.
net_group string	Name of net-group.
port_group string	Name of port-group.
port_protocol dictionary	Specify the source port or protocol.
eq string	Match only packets on a given port number.
gt string	Match only packets with a greater port number.
lt string	Match only packets with a lower port number.
neq string	Match only packets not on a given port number.
range dictionary	Match only packets in the range of port numbers
end string	Specify the end of the port range
start string	Specify the start of the port range
prefix string	Destination network prefix.
wildcard_bits string	The Wildcard bits to apply to destination address.
destopts boolean	Match if destination opts header is present. Choices: `false` `true`
dscp dictionary	Match packets with given DSCP value.
eq string	Match only packets on a given dscp value
gt string	Match only packets with a greater dscp value
lt string	Match only packets with a lower dscp value
neq string	Match only packets not on a given dscp value
range dictionary	Match only packets in the range of dscp values
end string	End of the dscp range
start string	Start of the dscp range
fragments boolean	Check non-intial fragments. Choices: `false` `true`
grant string	Forward or drop packets matching the Access Control Entry (ACE). Choices: `"permit"` `"deny"`
hop_by_hop boolean	Match if hop-by-hop opts header is present. Choices: `false` `true`
icmp_off boolean	Enable/disable the ICMP message for this entry. Choices: `false` `true`
line aliases: ace string	An ACE excluding the sequence number. This key is mutually exclusive with all the other attributes except ‘sequence’. When used with other attributes, the value of this key will get precedence and the other keys will be ignored. This should only be used when an attribute doesn’t exist in the argspec but is valid for the device. For fact gathering, any ACE that is not fully parsed, will show up as a value of this attribute, excluding the sequence number, which will be populated as value of the sequence key.
log boolean	Enable/disable log matches against this entry. Choices: `false` `true`
log_input boolean	Enable/disable log matches against this entry, including input interface. Choices: `false` `true`
packet_length dictionary	Match packets given packet length.
eq integer	Match only packets on a given packet length
gt integer	Match only packets with a greater packet length
lt integer	Match only packets with a lower packet length
neq integer	Match only packets not on a given packet length
range dictionary	Match only packets in the range of packet lengths
end integer	End of the packet length range
start integer	Start of the packet length range
precedence string	Match packets with given precedence value
protocol string	Specify the protocol to match. Refer to vendor documentation for valid values.
protocol_options dictionary	Additional suboptions for the protocol.
icmp dictionary	Internet Control Message Protocol settings.
administratively_prohibited boolean	Administratively prohibited Choices: `false` `true`
alternate_address boolean	Alternate address Choices: `false` `true`
conversion_error boolean	Datagram conversion Choices: `false` `true`
dod_host_prohibited boolean	Host prohibited Choices: `false` `true`
dod_net_prohibited boolean	Net prohibited Choices: `false` `true`
echo boolean	Echo (ping) Choices: `false` `true`
echo_reply boolean	Echo reply Choices: `false` `true`
general_parameter_problem boolean	Parameter problem Choices: `false` `true`
host_isolated boolean	Host isolated Choices: `false` `true`
host_precedence_unreachable boolean	Host unreachable for precedence Choices: `false` `true`
host_redirect boolean	Host redirect Choices: `false` `true`
host_tos_redirect boolean	Host redirect for TOS Choices: `false` `true`
host_tos_unreachable boolean	Host unreachable for TOS Choices: `false` `true`
host_unknown boolean	Host unknown Choices: `false` `true`
host_unreachable boolean	Host unreachable Choices: `false` `true`
information_reply boolean	Information replies Choices: `false` `true`
information_request boolean	Information requests Choices: `false` `true`
mask_reply boolean	Mask replies Choices: `false` `true`
mask_request boolean	Mask requests Choices: `false` `true`
mobile_redirect boolean	Mobile host redirect Choices: `false` `true`
net_redirect boolean	Network redirect Choices: `false` `true`
net_tos_redirect boolean	Net redirect for TOS Choices: `false` `true`
net_tos_unreachable boolean	Network unreachable for TOS Choices: `false` `true`
net_unreachable boolean	Net unreachable Choices: `false` `true`
network_unknown boolean	Network unknown Choices: `false` `true`
no_room_for_option boolean	Parameter required but no room Choices: `false` `true`
option_missing boolean	Parameter required but not present Choices: `false` `true`
packet_too_big boolean	Fragmentation needed and DF set Choices: `false` `true`
parameter_problem boolean	All parameter problems Choices: `false` `true`
port_unreachable boolean	Port unreachable Choices: `false` `true`
precedence_unreachable boolean	Precedence cutoff Choices: `false` `true`
protocol_unreachable boolean	Protocol unreachable Choices: `false` `true`
reassembly_timeout boolean	Reassembly timeout Choices: `false` `true`
redirect boolean	All redirects Choices: `false` `true`
router_advertisement boolean	Router discovery advertisements Choices: `false` `true`
router_solicitation boolean	Router discovery solicitations Choices: `false` `true`
source_quench boolean	Source quenches Choices: `false` `true`
source_route_failed boolean	Source route failed Choices: `false` `true`
time_exceeded boolean	All time exceededs Choices: `false` `true`
timestamp_reply boolean	Timestamp replies Choices: `false` `true`
timestamp_request boolean	Timestamp requests Choices: `false` `true`
traceroute boolean	Traceroute Choices: `false` `true`
ttl_exceeded boolean	TTL exceeded Choices: `false` `true`
unreachable boolean	All unreachables Choices: `false` `true`
icmpv6 dictionary	Internet Control Message Protocol settings for IPv6.
address_unreachable boolean	Address Unreachable Choices: `false` `true`
administratively_prohibited boolean	Administratively Prohibited Choices: `false` `true`
beyond_scope_of_source_address boolean	Administratively Prohibited Choices: `false` `true`
destination_unreachable boolean	Destination Unreachable Choices: `false` `true`
echo boolean	Echo Choices: `false` `true`
echo_reply boolean	Echo Reply Choices: `false` `true`
erroneous_header_field boolean	Erroneous Header Field Choices: `false` `true`
group_membership_query boolean	Group Membership Query Choices: `false` `true`
group_membership_report boolean	Group Membership Report Choices: `false` `true`
group_membership_termination boolean	Group Membership Termination Choices: `false` `true`
host_unreachable boolean	Host Unreachable Choices: `false` `true`
nd_na boolean	Neighbor Discovery - Neighbor Advertisement Choices: `false` `true`
nd_ns boolean	Neighbor Discovery - Neighbor Solicitation Choices: `false` `true`
neighbor_redirect boolean	Neighbor Redirect Choices: `false` `true`
no_route_to_destination boolean	No Route To Destination Choices: `false` `true`
node_information_request_is_refused boolean	Node Information Request Is Refused Choices: `false` `true`
node_information_successful_reply boolean	Node Information Successful Reply Choices: `false` `true`
packet_too_big boolean	Packet Too Big Choices: `false` `true`
parameter_problem boolean	Parameter Problem Choices: `false` `true`
port_unreachable boolean	Port Unreachable Choices: `false` `true`
query_subject_is_domainname boolean	Query Subject Is Domain name Choices: `false` `true`
query_subject_is_IPv4address boolean	Query Subject Is IPv4 address Choices: `false` `true`
query_subject_is_IPv6address boolean	Query Subject Is IPv6 address Choices: `false` `true`
reassembly_timeout boolean	Reassembly Timeout Choices: `false` `true`
redirect boolean	Redirect Choices: `false` `true`
router_advertisement boolean	Router Advertisement Choices: `false` `true`
router_renumbering boolean	Router Renumbering Choices: `false` `true`
router_solicitation boolean	Router Solicitation Choices: `false` `true`
rr_command boolean	RR Command Choices: `false` `true`
rr_result boolean	RR Result Choices: `false` `true`
rr_seqnum_reset boolean	RR Seqnum Reset Choices: `false` `true`
time_exceeded boolean	Time Exceeded Choices: `false` `true`
ttl_exceeded boolean	TTL Exceeded Choices: `false` `true`
unknown_query_type boolean	Unknown Query Type Choices: `false` `true`
unreachable boolean	Unreachable Choices: `false` `true`
unrecognized_next_header boolean	Unrecognized Next Header Choices: `false` `true`
unrecognized_option boolean	Unrecognized Option Choices: `false` `true`
whoareyou_reply boolean	Whoareyou Reply Choices: `false` `true`
whoareyou_request boolean	Whoareyou Request Choices: `false` `true`
igmp dictionary	Internet Group Management Protocol (IGMP) settings.
dvmrp boolean	Match Distance Vector Multicast Routing Protocol Choices: `false` `true`
host_query boolean	Match Host Query Choices: `false` `true`
host_report boolean	Match Host Report Choices: `false` `true`
mtrace boolean	Match mtrace Choices: `false` `true`
mtrace_response boolean	Match mtrace response Choices: `false` `true`
pim boolean	Match Protocol Independent Multicast Choices: `false` `true`
trace boolean	Multicast trace Choices: `false` `true`
tcp dictionary	Match TCP packet flags
ack boolean	Match on the ACK bit Choices: `false` `true`
established boolean	Match established connections Choices: `false` `true`
fin boolean	Match on the FIN bit Choices: `false` `true`
psh boolean	Match on the PSH bit Choices: `false` `true`
rst boolean	Match on the RST bit Choices: `false` `true`
syn boolean	Match on the SYN bit Choices: `false` `true`
urg boolean	Match on the URG bit Choices: `false` `true`
remark string	Comments or a description for the access list.
routing boolean	Match if routing header is present. Choices: `false` `true`
sequence integer	Sequence number for the Access Control Entry (ACE).
source dictionary	Specifies the packet source.
address string	The source IP address to match.
any boolean	Match any source address. Choices: `false` `true`
host string	The host IP address to match.
net_group string	Name of net-group.
port_group string	Name of port-group.
port_protocol dictionary	Specify the source port or protocol.
eq string	Match only packets on a given port number.
gt string	Match only packets with a greater port number.
lt string	Match only packets with a lower port number.
neq string	Match only packets not on a given port number.
range dictionary	Match only packets in the range of port numbers
end string	Specify the end of the port range
start string	Specify the start of the port range
prefix string	Source network prefix.
wildcard_bits string	The Wildcard bits to apply to source address.
ttl dictionary	Match against specified TTL value.
eq integer	Match only packets with exact TTL value.
gt integer	Match only packets with a greater TTL value.
lt integer	Match only packets with a lower TTL value.
neq integer	Match only packets that won’t have the given TTL value.
range dictionary	Match only packets in the range of given TTL values.
end integer	End of the TTL range.
start integer	Start of the TTL range.
name string	The name of the Access Control List (ACL).
afi string / required	The Address Family Indicator (AFI) for the Access Control Lists (ACL). Choices: `"ipv4"` `"ipv6"`
running_config string	The module, by default, will connect to the remote device and retrieve the current running-config to use as a base for comparing against the contents of source. There are times when it is not desirable to have the task get the current running-config for every task in a playbook. The running_config argument allows the implementer to pass in the configuration to use as the base config for comparison. This value of this option should be the output received from device by executing command show running-config router static.
state string	The state the configuration should be left in. Choices: `"merged"` ← (default) `"replaced"` `"overridden"` `"deleted"` `"gathered"` `"rendered"` `"parsed"`

Examples 

# Using merged to add new ACLs

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:07:45.767 UTC
# RP/0/RP0/CPU0:ios#

- name: Merge the provided configuration with the existing running configuration
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv6
      acls:
      - name: acl6_1
        aces:
        - sequence: 10
          grant: deny
          protocol: tcp
          source:
            prefix: 2001:db8:1234::/48
            port_protocol:
              range:
                start: ftp
                end: telnet
          destination:
            any: true
          protocol_options:
            tcp:
              syn: true
          ttl:
            range:
              start: 180
              end: 250
          routing: true
          authen: true
          log: true

        - sequence: 20
          grant: permit
          protocol: icmpv6
          source:
            any: true
          destination:
            any: true
          protocol_options:
            icmpv6:
              router_advertisement: true
          precedence: network
          destopts: true

    - afi: ipv4
      acls:
      - name: acl_1
        aces:
        - sequence: 16
          remark: TEST_ACL_1_REMARK

        - sequence: 21
          grant: permit
          protocol: tcp
          source:
            host: 192.0.2.10
            port_protocol:
              range:
                start: pop3
                end: 121
          destination:
            address: 198.51.100.0
            wildcard_bits: 0.0.0.15
          protocol_options:
            tcp:
              rst: true

        - sequence: 23
          grant: deny
          protocol: icmp
          source:
            any: true
          destination:
            prefix: 198.51.100.0/28
          protocol_options:
            icmp:
              reassembly_timeout: true
          dscp:
            lt: af12

      - name: acl_2
        aces:
        - sequence: 10
          remark: TEST_ACL_2_REMARK
    state: merged

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

# Using merged to update existing ACLs

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

- name: Update existing ACEs
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv4
      acls:
      - name: acl_1
        aces:
        - sequence: 21
          source:
            prefix: 198.51.100.32/28
            port_protocol:
              range:
                start: pop3
                end: 121
          protocol_options:
            tcp:
              syn: true

        - sequence: 23
          protocol_options:
            icmp:
              router_advertisement: true
          dscp:
            eq: af23

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:47:18.711 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp 198.51.100.32 0.0.0.15 range pop3 121 198.51.100.0 0.0.0.15 syn
#  23 deny icmp any 198.51.100.0 0.0.0.15 router-advertisement dscp eq af23
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

# Using replaced to replace a whole ACL

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

- name: Replace device configurations of listed ACL with provided configurations
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv4
      acls:
      - name: acl_2
        aces:
        - sequence: 11
          grant: permit
          protocol: igmp
          source:
            host: 198.51.100.130
          destination:
            any: true
          ttl:
            eq: 100

        - sequence: 12
          grant: deny
          source:
            any: true
          destination:
            any: true
          protocol: icmp
    state: replaced

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 06:19:51.496 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp 198.51.100.32 0.0.0.15 range pop3 121 198.51.100.0 0.0.0.15 syn
#  23 deny icmp any 198.51.100.0 0.0.0.15 router-advertisement dscp eq af23
# ipv4 access-list acl_2
#  11 permit igmp host 198.51.100.130 any ttl eq 100
#  12 deny icmp any any
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

# Using overridden to override all ACLs in the device

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

- name: Overridde all ACLs configuration with provided configuration
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv4
      acls:
      - name: acl_1
        aces:
        - sequence: 10
          grant: permit
          source:
            any: true
          destination:
            any: true
          protocol: tcp

      - name: acl_2
        aces:
        - sequence: 20
          grant: permit
          source:
            any: true
          destination:
            any: true
          protocol: igmp
    state: overridden

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 06:31:22.178 UTC
# ipv4 access-list acl_1
#  10 permit tcp any any
# ipv4 access-list acl_2
#  20 permit igmp any any

# Using deleted to delete an entire ACL

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

- name: Delete a single ACL
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv6
      acls:
      - name: acl6_1
    state: deleted

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK

# Using deleted to delete all ACLs under one AFI

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

- name: Delete all ACLs under one AFI
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv4
    state: deleted

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

# Using deleted to delete all ACLs from the device

# Before state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:22:57.021 UTC
# ipv4 access-list acl_1
#  16 remark TEST_ACL_1_REMARK
#  21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst
#  23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12
# ipv4 access-list acl_2
#  10 remark TEST_ACL_2_REMARK
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network destopts

- name: Delete all ACLs from the device
  cisco.iosxr.iosxr_acls:
    state: deleted

# After state:
# -------------

# RP/0/RP0/CPU0:ios#sh access-lists afi-all
# Thu Feb 20 05:07:45.767 UTC
# RP/0/RP0/CPU0:ios#

# Using gathered to gather ACL facts from the device

- name: Gather ACL interfaces facts using gathered state
  cisco.iosxr.iosxr_acls:
    state: gathered

# Task Output (redacted)
# -----------------------
#

# "gathered": [
#    {
#        "acls": [
#            {
#                "aces": [
#                    {
#                        "remark": "TEST_ACL_1_REMARK",
#                        "sequence": 16
#                    },
#                    {
#                        "destination": {
#                            "address": "198.51.100.0",
#                            "wildcard_bits": "0.0.0.15"
#                        },
#                        "grant": "permit",
#                        "protocol": "tcp",
#                        "protocol_options": {
#                            "tcp": {
#                                "rst": true
#                            }
#                        },
#                        "sequence": 21,
#                        "source": {
#                            "host": "192.0.2.10",
#                            "port_protocol": {
#                                "range": {
#                                    "end": "121",
#                                    "start": "pop3"
#                                }
#                            }
#                        }
#                    },
#                    {
#                        "destination": {
#                            "address": "198.51.100.0",
#                            "wildcard_bits": "0.0.0.15"
#                        },
#                        "dscp": {
#                            "lt": "af12"
#                        },
#                        "grant": "deny",
#                        "protocol": "icmp",
#                        "protocol_options": {
#                            "icmp": {
#                                "reassembly_timeout": true
#                            }
#                        },
#                        "sequence": 23,
#                        "source": {
#                            "any": true
#                        }
#                    }
#                ],
#                "name": "acl_1"
#            },
#            {
#                "aces": [
#                    {
#                        "remark": "TEST_ACL_2_REMARK",
#                        "sequence": 10
#                    }
#                ],
#                "name": "acl_2"
#            }
#        ],
#        "afi": "ipv4"
#    },
#    {
#        "acls": [
#            {
#                "aces": [
#                    {
#                        "authen": true,
#                        "destination": {
#                            "any": true
#                        },
#                        "grant": "deny",
#                        "log": true,
#                        "protocol": "tcp",
#                        "protocol_options": {
#                            "tcp": {
#                                "syn": true
#                            }
#                        },
#                        "routing": true,
#                        "sequence": 10,
#                        "source": {
#                            "port_protocol": {
#                                "range": {
#                                   "end": "telnet",
#                                   "start": "ftp"
#                                }
#                            },
#                            "prefix": "2001:db8:1234::/48"
#                        },
#                        "ttl": {
#                            "range": {
#                                "end": 250,
#                                "start": 180
#                            }
#                        }
#                    },
#                    {
#                        "destination": {
#                            "any": true
#                        },
#                        "destopts": true,
#                        "grant": "permit",
#                        "precedence": "network",
#                        "protocol": "icmpv6",
#                        "protocol_options": {
#                            "icmpv6": {
#                                "router_advertisement": true
#                            }
#                        },
#                        "sequence": 20,
#                        "source": {
#                            "any": true
#                        }
#                    }
#                ],
#                "name": "acl6_1"
#            }
#        ],
#        "afi": "ipv6"
#    }
#  ]

# Using rendered

- name: Render platform specific commands (without connecting to the device)
  cisco.iosxr.iosxr_acls:
    config:
    - afi: ipv4
      acls:
      - name: acl_2
        aces:
        - sequence: 11
          grant: permit
          protocol: igmp
          source:
            host: 198.51.100.130
          destination:
            any: true
          ttl:
            eq: 100

        - sequence: 12
          grant: deny
          source:
            any: true
          destination:
            any: true
          protocol: icmp
    state: rendered

# Task Output (redacted)
# -----------------------

# "rendered": [
#    "ipv4 access-list acl_2",
#    "11 permit igmp host 198.51.100.130 any ttl eq 100",
#    "12 deny icmp any any"

# Using parsed

# parsed.cfg
# ------------
#
# ipv4 access-list acl_1
#  10 remark TEST_ACL_2_REMARK
# ipv4 access-list acl_2
#  11 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 authen routing log
#  21 permit icmpv6 any any router-advertisement precedence network packet-length eq 576 destopts
# ipv6 access-list acl6_1
#  10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 routing authen log
#  20 permit icmpv6 any any router-advertisement precedence network packet-length eq 576 destopts

- name: Parse externally provided ACL config to agnostic model
  cisco.iosxr.iosxr_acls:
    running_config: "{{ lookup('file', 'parsed.cfg') }}"
    state: parsed

# Task Output (redacted)
# -----------------------
#  "parsed": [
#        {
#            "acls": [
#                {
#                    "aces": [
#                      {
#                            "remark": "TEST_ACL_2_REMARK",
#                            "sequence": 10
#                        }
#                    ],
#                   "name": "acl_1"
#                },
#                {
#                    "aces": [
#                        {
#                            "authen": true,
#                            "destination": {
#                                "any": true
#                            },
#                            "grant": "deny",
#                            "log": true,
#                            "protocol": "tcp",
#                            "protocol_options": {
#                                "tcp": {
#                                    "syn": true
#                                }
#                            },
#                            "routing": true,
#                            "sequence": 11,
#                            "source": {
#                                "port_protocol": {
#                                    "range": {
#                                        "end": "telnet",
#                                        "start": "ftp"
#                                    }
#                                },
#                                "prefix": "2001:db8:1234::/48"
#                            },
#                            "ttl": {
#                                "range": {
#                                    "end": 250,
#                                    "start": 180
#                                }
#                            }
#                        },
#                        {
#                            "destination": {
#                                "any": true
#                            },
#                            "destopts": true,
#                            "grant": "permit",
#                            "packet_length": {
#                                "eq": 576
#                            },
#                            "precedence": "network",
#                            "protocol": "icmpv6",
#                            "protocol_options": {
#                                "icmpv6": {
#                                    "router_advertisement": true
#                                }
#                            },
#                            "sequence": 21,
#                            "source": {
#                                "any": true
#                            }
#                        }
#                    ],
#                    "name": "acl_2"
#                }
#            ],
#            "afi": "ipv4"
#        },
#        {
#            "acls": [
#                {
#                    "aces": [
#                        {
#                            "authen": true,
#                            "destination": {
#                                "any": true
#                            },
#                            "grant": "deny",
#                            "log": true,
#                            "protocol": "tcp",
#                            "protocol_options": {
#                                "tcp": {
#                                    "syn": true
#                                }
#                            },
#                            "routing": true,
#                            "sequence": 10,
#                            "source": {
#                                "port_protocol": {
#                                    "range": {
#                                        "end": "telnet",
#                                        "start": "ftp"
#                                    }
#                                },
#                                "prefix": "2001:db8:1234::/48"
#                            },
#                            "ttl": {
#                                "range": {
#                                    "end": 250,
#                                    "start": 180
#                                }
#                            }
#                        },
#                        {
#                            "destination": {
#                                "any": true
#                            },
#                            "destopts": true,
#                            "grant": "permit",
#                            "packet_length": {
#                                "eq": 576
#                            },
#                            "precedence": "network",
#                            "protocol": "icmpv6",
#                            "protocol_options": {
#                                "icmpv6": {
#                                    "router_advertisement": true
#                                }
#                            },
#                            "sequence": 20,
#                            "source": {
#                                "any": true
#                            }
#                        }
#                    ],
#                    "name": "acl6_1"
#                }
#            ],
#            "afi": "ipv6"
#        }
#    ]

Return Values 

Common return values are documented here, the following are the fields unique to this module:

Key	Description
after list / elements=string	The resulting configuration model invocation. Returned: when changed Sample: `["The configuration returned will always be in the same format\n of the parameters above.\n"]`
before list / elements=string	The configuration prior to the model invocation. Returned: always Sample: `["The configuration returned will always be in the same format\n of the parameters above.\n"]`
commands list / elements=string	The set of commands pushed to the remote device. Returned: always Sample: `["ipv6 access-list acl6_1", "10 deny tcp 2001:db8:1234::/48 range ftp telnet any syn ttl range 180 250 authen routing log", "20 permit icmpv6 any any router-advertisement precedence network destopts", "ipv4 access-list acl_1", "16 remark TEST_ACL_1_REMARK", "21 permit tcp host 192.0.2.10 range pop3 121 198.51.100.0 0.0.0.15 rst", "23 deny icmp any 198.51.100.0 0.0.0.15 reassembly-timeout dscp lt af12"]`

Authors

Nilashish Chakraborty (@NilashishC)

cisco.iosxr.iosxr_acls module – Resource module to configure ACLs.

Synopsis

Parameters

Examples

Return Values