cisco.nxos.nxos_igmp_interface module – Manages IGMP interface configuration.

Note

This module is part of the cisco.nxos collection (version 4.4.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install cisco.nxos.

To use it in a playbook, specify: cisco.nxos.nxos_igmp_interface.

New in cisco.nxos 1.0.0

Synopsis

  • Manages IGMP interface configuration settings.

Note

This module has a corresponding action plugin.

Aliases: igmp_interface

Parameters

Parameter

Comments

group_timeout

string

Sets the group membership timeout for IGMPv2. Values can range from 3 to 65,535 seconds or keyword ‘default’. The default is 260 seconds.

immediate_leave

boolean

Enables the device to remove the group entry from the multicast routing table immediately upon receiving a leave message for the group. Use this command to minimize the leave latency of IGMPv2 group memberships on a given IGMP interface because the device does not send group-specific queries. The default is disabled.

Choices:

  • false

  • true

interface

string / required

The full interface name for IGMP configuration. e.g. Ethernet1/2.

last_member_qrt

string

Sets the query interval waited after sending membership reports before the software deletes the group state. Values can range from 1 to 25 seconds or keyword ‘default’. The default is 1 second.

last_member_query_count

string

Sets the number of times that the software sends an IGMP query in response to a host leave message. Values can range from 1 to 5 or keyword ‘default’. The default is 2.

oif_ps

any

Configure prefixes and sources for static outgoing interface (OIF). This is a list of dict where each dict has source and prefix defined or just prefix if source is not needed. The specified values will be configured on the device and if any previous prefix/sources exist, they will be removed. Keyword ‘default’ is also accepted which removes all existing prefix/sources.

oif_routemap

string

Configure a routemap for static outgoing interface (OIF) or keyword ‘default’.

querier_timeout

string

Sets the querier timeout that the software uses when deciding to take over as the querier. Values can range from 1 to 65535 seconds or keyword ‘default’. The default is 255 seconds.

query_interval

string

Sets the frequency at which the software sends IGMP host query messages. Values can range from 1 to 18000 seconds or keyword ‘default’. The default is 125 seconds.

query_mrt

string

Sets the response time advertised in IGMP queries. Values can range from 1 to 25 seconds or keyword ‘default’. The default is 10 seconds.

report_llg

boolean

Configures report-link-local-groups. Enables sending reports for groups in 224.0.0.0/24. Reports are always sent for nonlink local groups. By default, reports are not sent for link local groups.

Choices:

  • false

  • true

restart

boolean

Restart IGMP. This is NOT idempotent as this is action only.

Choices:

  • false ← (default)

  • true

robustness

string

Sets the robustness variable. Values can range from 1 to 7 or keyword ‘default’. The default is 2.

startup_query_count

string

Query count used when the IGMP process starts up. The range is from 1 to 10 or keyword ‘default’. The default is 2.

startup_query_interval

string

Query interval used when the IGMP process starts up. The range is from 1 to 18000 or keyword ‘default’. The default is 31.

state

string

Manages desired state of the resource.

Choices:

  • "present" ← (default)

  • "absent"

  • "default"

version

string

IGMP version. It can be 2 or 3 or keyword ‘default’.

Choices:

  • "2"

  • "3"

  • "default"

Notes

Note

  • Tested against NXOSv 7.3.(0)D1(1) on VIRL

  • Unsupported for Cisco MDS

  • When state=default, supported params will be reset to a default state. These include version, startup_query_interval, startup_query_count, robustness, querier_timeout, query_mrt, query_interval, last_member_qrt, last_member_query_count, group_timeout, report_llg, and immediate_leave.

  • When state=absent, all configs for oif_ps, and oif_routemap will be removed.

  • PIM must be enabled to use this module.

  • This module is for Layer 3 interfaces.

  • Route-map check not performed (same as CLI) check when configuring route-map with ‘static-oif’

  • If restart is set to true with other params set, the restart will happen last, i.e. after the configuration takes place. However, ‘restart’ itself is not idempotent as it is an action and not configuration.

  • For information on using CLI and NX-API see the :ref:`NXOS Platform Options guide <nxos_platform_options>`

  • For more information on using Ansible to manage network devices see the :ref:`Ansible Network Guide <network_guide>`

  • For more information on using Ansible to manage Cisco devices see the `Cisco integration page <https://www.ansible.com/integrations/networks/cisco>`_.

Examples

- cisco.nxos.nxos_igmp_interface:
    interface: ethernet1/32
    startup_query_interval: 30
    oif_ps:
    - {prefix: 238.2.2.6}
    - {source: 192.168.0.1, prefix: 238.2.2.5}
    state: present

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key

Description

changed

boolean

check to see if a change was made on the device

Returned: always

Sample: true

end_state

dictionary

k/v pairs of igmp interface configuration after module execution

Returned: always

Sample: {"oif_ps": [{"prefix": "238.2.2.6"}, {"prefix": "238.2.2.5", "source": "192.168.0.1"}], "startup_query_count": "30"}

existing

dictionary

k/v pairs of existing igmp_interface configuration

Returned: always

Sample: {"oif_ps": [], "startup_query_count": "2"}

proposed

dictionary

k/v pairs of parameters passed into module

Returned: always

Sample: {"oif_ps": [{"prefix": "238.2.2.6"}, {"prefix": "238.2.2.5", "source": "192.168.0.1"}], "startup_query_count": "30"}

updates

list / elements=string

commands sent to the device

Returned: always

Sample: ["interface Ethernet1/32", "ip igmp startup-query-count 30", "ip igmp static-oif 238.2.2.6", "ip igmp static-oif 238.2.2.5 source 192.168.0.1"]

Authors

  • Jason Edelman (@jedelman8)

  • Gabriele Gerbino (@GGabriele)