community.vmware.vmware_dvs_portgroup module – Create or remove a Distributed vSwitch portgroup.

Note

This module is part of the community.vmware collection (version 3.11.1).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install community.vmware.

To use it in a playbook, specify: community.vmware.vmware_dvs_portgroup.

Synopsis

  • Create or remove a Distributed vSwitch portgroup.

Parameters

Parameter

Comments

hostname

string

The hostname or IP address of the vSphere vCenter or ESXi server.

If the value is not specified in the task, the value of environment variable VMWARE_HOST will be used instead.

Environment variable support added in Ansible 2.6.

in_traffic_shaping

dictionary

added in community.vmware 2.3.0

Dictionary which configures the ingress traffic shaping settings for the portgroup.

average_bandwidth

integer

Establishes the number of bits per second to allow across a port, averaged over time, that is, the allowed average load.

Ignored if inherited is true.

burst_size

integer

The maximum number of bits per second to allow across a port when it is sending/sending or receiving a burst of traffic.

Ignored if inherited is true.

enabled

boolean

Indicates whether ingress traffic shaping is activated or not.

Ignored if inherited is true.

Choices:

  • false

  • true

inherited

boolean / required

Inherit the settings from the switch or not.

Choices:

  • false

  • true

peak_bandwidth

integer

The maximum number of bytes to allow in a burst.

Ignored if inherited is true.

mac_learning

dictionary

Dictionary which configures MAC learning for portgroup.

allow_unicast_flooding

boolean

The flag to allow flooding of unlearned MAC for ingress traffic.

Choices:

  • false

  • true

enabled

boolean

The flag to indicate if source MAC address learning is allowed.

Choices:

  • false

  • true

limit

integer

The maximum number of MAC addresses that can be learned.

limit_policy

string

The default switching policy after MAC limit is exceeded.

Choices:

  • "allow"

  • "drop"

net_flow

string

added in community.vmware 2.3.0

Indicate whether or not the virtual machine IP traffic that flows through a vds gets analyzed by sending reports to a NetFlow collector.

Choices:

  • "true"

  • "on"

  • "yes"

  • "false"

  • "off"

  • "no"

  • "inherited"

network_policy

dictionary

Dictionary which configures the different security values for portgroup.

forged_transmits

boolean

Indicates whether forged transmits are allowed. Ignored if inherited is true.

Choices:

  • false

  • true

inherited

boolean / required

Inherit the settings from the switch or not.

Choices:

  • false

  • true

mac_changes

boolean

Indicates whether mac changes are allowed. Ignored if inherited is true.

Choices:

  • false

  • true

promiscuous

boolean

Indicates whether promiscuous mode is allowed. Ignored if inherited is true.

Choices:

  • false

  • true

num_ports

integer

The number of ports the portgroup should contain.

out_traffic_shaping

dictionary

added in community.vmware 2.3.0

Dictionary which configures the egress traffic shaping settings for the portgroup.

average_bandwidth

integer

Establishes the number of bits per second to allow across a port, averaged over time, that is, the allowed average load.

Ignored if inherited is true.

burst_size

integer

The maximum number of bits per second to allow across a port when it is sending/sending or receiving a burst of traffic.

Ignored if inherited is true.

enabled

boolean

Indicates whether egress traffic shaping is activated or not.

Ignored if inherited is true.

Choices:

  • false

  • true

inherited

boolean / required

Inherit the settings from the switch or not.

Choices:

  • false

  • true

peak_bandwidth

integer

The maximum number of bytes to allow in a burst.

Ignored if inherited is true.

password

aliases: pass, pwd

string

The password of the vSphere vCenter or ESXi server.

If the value is not specified in the task, the value of environment variable VMWARE_PASSWORD will be used instead.

Environment variable support added in Ansible 2.6.

port

integer

The port number of the vSphere vCenter or ESXi server.

If the value is not specified in the task, the value of environment variable VMWARE_PORT will be used instead.

Environment variable support added in Ansible 2.6.

Default: 443

port_allocation

string

Elastic port groups automatically increase or decrease the number of ports as needed.

Only valid if port_binding is set to static.

Will be elastic if not specified and port_binding is set to static.

Will be fixed if not specified and port_binding is set to ephemeral.

Choices:

  • "elastic"

  • "fixed"

port_binding

string / required

The type of port binding determines when ports in a port group are assigned to virtual machines.

See VMware KB 1022312 https://kb.vmware.com/s/article/1022312 for more details.

Choices:

  • "static"

  • "ephemeral"

port_policy

dictionary

Dictionary which configures the advanced policy settings for the portgroup.

Default: {"block_override": true, "ipfix_override": false, "live_port_move": false, "mac_management_override": false, "network_rp_override": false, "port_config_reset_at_disconnect": true, "shaping_override": false, "traffic_filter_override": false, "uplink_teaming_override": false, "vendor_config_override": false, "vlan_override": false}

block_override

boolean

Indicates if the block policy can be changed per port.

Choices:

  • false

  • true ← (default)

ipfix_override

boolean

Indicates if the ipfix policy can be changed per port.

Choices:

  • false ← (default)

  • true

live_port_move

boolean

Indicates if a live port can be moved in or out of the portgroup.

Choices:

  • false ← (default)

  • true

mac_management_override

aliases: security_override

boolean

Indicates if the security policy can be changed per port.

Choices:

  • false ← (default)

  • true

network_rp_override

boolean

Indicates if the network resource pool can be changed per port.

Choices:

  • false ← (default)

  • true

port_config_reset_at_disconnect

boolean

Indicates if the configuration of a port is reset automatically after disconnect.

Choices:

  • false

  • true ← (default)

shaping_override

boolean

Indicates if the shaping policy can be changed per port.

Choices:

  • false ← (default)

  • true

traffic_filter_override

boolean

Indicates if the traffic filter can be changed per port.

Choices:

  • false ← (default)

  • true

boolean

Indicates if the uplink teaming policy can be changed per port.

Choices:

  • false ← (default)

  • true

vendor_config_override

boolean

Indicates if the vendor config can be changed per port.

Choices:

  • false ← (default)

  • true

vlan_override

boolean

Indicates if the vlan can be changed per port.

Choices:

  • false ← (default)

  • true

portgroup_name

string / required

The name of the portgroup that is to be created or deleted.

proxy_host

string

Address of a proxy that will receive all HTTPS requests and relay them.

The format is a hostname or a IP.

If the value is not specified in the task, the value of environment variable VMWARE_PROXY_HOST will be used instead.

This feature depends on a version of pyvmomi greater than v6.7.1.2018.12

proxy_port

integer

Port of the HTTP proxy that will receive all HTTPS requests and relay them.

If the value is not specified in the task, the value of environment variable VMWARE_PROXY_PORT will be used instead.

state

string / required

Determines if the portgroup should be present or not.

Choices:

  • "present"

  • "absent"

switch_name

string / required

The name of the distributed vSwitch the port group should be created on.

teaming_policy

dictionary

Dictionary which configures the different teaming values for portgroup.

Default: {"load_balance_policy": "loadbalance_srcid", "notify_switches": true, "rolling_order": false}

list / elements=string

List of active uplinks used for load balancing.

inbound_policy

boolean

Indicate whether or not the teaming policy is applied to inbound frames as well.

Choices:

  • false

  • true

load_balance_policy

string

Network adapter teaming policy.

loadbalance_loadbased is available from version 2.6 and onwards.

Choices:

  • "loadbalance_ip"

  • "loadbalance_srcmac"

  • "loadbalance_srcid" ← (default)

  • "loadbalance_loadbased"

  • "failover_explicit"

notify_switches

boolean

Indicate whether or not to notify the physical switch if a link fails.

Choices:

  • false

  • true ← (default)

rolling_order

boolean

Indicate whether or not to use a rolling policy when restoring links.

Choices:

  • false ← (default)

  • true

list / elements=string

List of standby uplinks used for failover.

username

aliases: admin, user

string

The username of the vSphere vCenter or ESXi server.

If the value is not specified in the task, the value of environment variable VMWARE_USER will be used instead.

Environment variable support added in Ansible 2.6.

validate_certs

boolean

Allows connection when SSL certificates are not valid. Set to false when certificates are not trusted.

If the value is not specified in the task, the value of environment variable VMWARE_VALIDATE_CERTS will be used instead.

Environment variable support added in Ansible 2.6.

If set to true, please make sure Python >= 2.7.9 is installed on the given machine.

Choices:

  • false

  • true ← (default)

vlan_id

string / required

The VLAN ID that should be configured with the portgroup, use 0 for no VLAN.

If vlan_trunk is configured to be true, this can be a combination of multiple ranges and numbers, example: 1-200, 205, 400-4094.

The valid vlan_id range is from 0 to 4094. Overlapping ranges are allowed.

If vlan_private is configured to be true, the corresponding private VLAN should already be configured in the distributed vSwitch.

vlan_private

boolean

Indicates whether this is for a private VLAN or not.

Mutually exclusive with vlan_trunk parameter.

Choices:

  • false ← (default)

  • true

vlan_trunk

boolean

Indicates whether this is a VLAN trunk or not.

Mutually exclusive with vlan_private parameter.

Choices:

  • false ← (default)

  • true

Notes

Note

  • All modules requires API write access and hence is not supported on a free ESXi license.

Examples

- name: Create vlan portgroup
  community.vmware.vmware_dvs_portgroup:
    hostname: '{{ vcenter_hostname }}'
    username: '{{ vcenter_username }}'
    password: '{{ vcenter_password }}'
    portgroup_name: vlan-123-portrgoup
    switch_name: dvSwitch
    vlan_id: 123
    num_ports: 120
    port_binding: static
    state: present
  delegate_to: localhost

- name: Create vlan trunk portgroup
  community.vmware.vmware_dvs_portgroup:
    hostname: '{{ vcenter_hostname }}'
    username: '{{ vcenter_username }}'
    password: '{{ vcenter_password }}'
    portgroup_name: vlan-trunk-portrgoup
    switch_name: dvSwitch
    vlan_id: 1-1000, 1005, 1100-1200
    vlan_trunk: true
    num_ports: 120
    port_binding: static
    state: present
  delegate_to: localhost

- name: Create private vlan portgroup
  vmware_dvs_portgroup:
    hostname: '{{ vcenter_hostname }}'
    username: '{{ vcenter_username }}'
    password: '{{ vcenter_password }}'
    portgroup_name: private-vlan-portrgoup
    switch_name: dvSwitch
    vlan_id: 1001
    vlan_private: true
    num_ports: 120
    port_binding: static
    state: present
  delegate_to: localhost

- name: Create no-vlan portgroup
  community.vmware.vmware_dvs_portgroup:
    hostname: '{{ vcenter_hostname }}'
    username: '{{ vcenter_username }}'
    password: '{{ vcenter_password }}'
    portgroup_name: no-vlan-portrgoup
    switch_name: dvSwitch
    vlan_id: 0
    num_ports: 120
    port_binding: static
    state: present
  delegate_to: localhost

- name: Create vlan portgroup with all security and port policies
  community.vmware.vmware_dvs_portgroup:
    hostname: '{{ vcenter_hostname }}'
    username: '{{ vcenter_username }}'
    password: '{{ vcenter_password }}'
    portgroup_name: vlan-123-portrgoup
    switch_name: dvSwitch
    vlan_id: 123
    num_ports: 120
    port_binding: static
    state: present
    network_policy:
      inherited: false
      promiscuous: true
      forged_transmits: true
      mac_changes: true
    port_policy:
      block_override: true
      ipfix_override: true
      live_port_move: true
      network_rp_override: true
      port_config_reset_at_disconnect: true
      mac_management_override: true
      shaping_override: true
      traffic_filter_override: true
      uplink_teaming_override: true
      vendor_config_override: true
      vlan_override: true
  delegate_to: localhost

Authors

  • Joseph Callen (@jcpowermac)

  • Philippe Dellaert (@pdellaert)