arista.eos.eos_acls module – ACLs resource module

Note

This module is part of the arista.eos collection (version 6.2.2).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install arista.eos.

To use it in a playbook, specify: arista.eos.eos_acls.

New in arista.eos 1.0.0

Synopsis 

This module manages the IP access-list attributes of Arista EOS interfaces.

Aliases: acls

Parameters 

Parameter	Comments
config list / elements=dictionary	A dictionary of IP access-list options
acls list / elements=dictionary	A list of Access Control Lists (ACL).
aces list / elements=dictionary	Filtering data
destination dictionary	The packet’s destination address
address string	dotted decimal notation of IP address
any boolean	Rule matches all source addresses Choices: `false` `true`
host string	Host IP address
port_protocol dictionary	Specify dest port/protocol, along with operator . (comes with tcp/udp).
subnet_address string	A subnet address
wildcard_bits string	Source wildcard bits
fragment_rules boolean	Add fragment rules Choices: `false` `true`
fragments boolean	Match non-head fragment packets Choices: `false` `true`
grant string	Action to be applied on the rule Choices: `"permit"` `"deny"`
hop_limit dictionary	Hop limit value.
line aliases: ace string	For fact gathering, any ACE that is not fully parsed, while show up as a value of this attribute.
log boolean	Log matches against this rule Choices: `false` `true`
protocol string	Specify the protocol to match. Refer to vendor documentation for valid values.
protocol_options dictionary	All the possible sub options for the protocol chosen.
icmp dictionary	Internet Control Message Protocol settings.
administratively_prohibited boolean	Administratively prohibited Choices: `false` `true`
alternate_address boolean	Alternate address Choices: `false` `true`
conversion_error boolean	Datagram conversion Choices: `false` `true`
dod_host_prohibited boolean	Host prohibited Choices: `false` `true`
dod_net_prohibited boolean	Net prohibited Choices: `false` `true`
echo boolean	Echo (ping) Choices: `false` `true`
echo_reply boolean	Echo reply Choices: `false` `true`
general_parameter_problem boolean	Parameter problem Choices: `false` `true`
host_isolated boolean	Host isolated Choices: `false` `true`
host_precedence_unreachable boolean	Host unreachable for precedence Choices: `false` `true`
host_redirect boolean	Host redirect Choices: `false` `true`
host_tos_redirect boolean	Host redirect for TOS Choices: `false` `true`
host_tos_unreachable boolean	Host unreachable for TOS Choices: `false` `true`
host_unknown boolean	Host unknown Choices: `false` `true`
host_unreachable boolean	Host unreachable Choices: `false` `true`
information_reply boolean	Information replies Choices: `false` `true`
information_request boolean	Information requests Choices: `false` `true`
mask_reply boolean	Mask replies Choices: `false` `true`
mask_request boolean	Mask requests Choices: `false` `true`
message_code integer	ICMP message code
message_num integer	icmp msg type number.
message_type integer	ICMP message type
mobile_redirect boolean	Mobile host redirect Choices: `false` `true`
net_redirect boolean	Network redirect Choices: `false` `true`
net_tos_redirect boolean	Net redirect for TOS Choices: `false` `true`
net_tos_unreachable boolean	Network unreachable for TOS Choices: `false` `true`
net_unreachable boolean	Net unreachable Choices: `false` `true`
network_unknown boolean	Network unknown Choices: `false` `true`
no_room_for_option boolean	Parameter required but no room Choices: `false` `true`
option_missing boolean	Parameter required but not present Choices: `false` `true`
packet_too_big boolean	Fragmentation needed and DF set Choices: `false` `true`
parameter_problem boolean	All parameter problems Choices: `false` `true`
port_unreachable boolean	Port unreachable Choices: `false` `true`
precedence_unreachable boolean	Precedence cutoff Choices: `false` `true`
protocol_unreachable boolean	Protocol unreachable Choices: `false` `true`
reassembly_timeout boolean	Reassembly timeout Choices: `false` `true`
redirect boolean	All redirects Choices: `false` `true`
router_advertisement boolean	Router discovery advertisements Choices: `false` `true`
router_solicitation boolean	Router discovery solicitations Choices: `false` `true`
source_quench boolean	Source quenches Choices: `false` `true`
source_route_failed boolean	Source route failed Choices: `false` `true`
time_exceeded boolean	All time exceededs Choices: `false` `true`
timestamp_reply boolean	Timestamp replies Choices: `false` `true`
timestamp_request boolean	Timestamp requests Choices: `false` `true`
traceroute boolean	Traceroute Choices: `false` `true`
ttl_exceeded boolean	TTL exceeded Choices: `false` `true`
unreachable boolean	All unreachables Choices: `false` `true`
icmpv6 dictionary	Options for icmpv6.
address_unreachable boolean	address unreachable Choices: `false` `true`
beyond_scope boolean	beyond_scope Choices: `false` `true`
echo_reply boolean	echo_reply Choices: `false` `true`
echo_request boolean	echo reques Choices: `false` `true`
erroneous_header boolean	erroneous header Choices: `false` `true`
fragment_reassembly_exceeded boolean	fragment_reassembly_exceeded Choices: `false` `true`
hop_limit_exceeded boolean	hop limit exceeded Choices: `false` `true`
neighbor_advertisement boolean	neighbor advertisement Choices: `false` `true`
neighbor_solicitation boolean	neighbor_solicitation Choices: `false` `true`
no_admin boolean	no admin Choices: `false` `true`
no_route boolean	no route Choices: `false` `true`
packet_too_big boolean	packet too big Choices: `false` `true`
parameter_problem boolean	parameter problem Choices: `false` `true`
port_unreachable boolean	port unreachable Choices: `false` `true`
redirect_message boolean	redirect message Choices: `false` `true`
reject_route boolean	reject route Choices: `false` `true`
router_advertisement boolean	router_advertisement Choices: `false` `true`
router_solicitation boolean	router_solicitation Choices: `false` `true`
source_address_failed boolean	source_address_failed Choices: `false` `true`
source_routing_error boolean	source_routing_error Choices: `false` `true`
time_exceeded boolean	time_exceeded Choices: `false` `true`
unreachable boolean	unreachable Choices: `false` `true`
unrecognized_ipv6_option boolean	unrecognized_ipv6_option Choices: `false` `true`
unrecognized_next_header boolean	unrecognized_next_header Choices: `false` `true`
ip dictionary	Internet Protocol.
nexthop_group string	Nexthop-group name.
ipv6 dictionary	Internet V6 Protocol.
nexthop_group string	Nexthop-group name.
tcp dictionary	Options for tcp protocol.
flags dictionary	Match TCP packet flags
ack boolean	Match on the ACK bit Choices: `false` `true`
established boolean	Match established connections Choices: `false` `true`
fin boolean	Match on the FIN bit Choices: `false` `true`
psh boolean	Match on the PSH bit Choices: `false` `true`
rst boolean	Match on the RST bit Choices: `false` `true`
syn boolean	Match on the SYN bit Choices: `false` `true`
urg boolean	Match on the URG bit Choices: `false` `true`
remark string	Specify a comment
sequence integer	sequence number for the ordered list of rules
source dictionary	The packet’s source address
address string	dotted decimal notation of IP address
any boolean	Rule matches all source addresses Choices: `false` `true`
host string	Host IP address
port_protocol dictionary	Specify source port/protocoli, along with operator. (comes with tcp/udp).
subnet_address string	A subnet address
wildcard_bits string	Source wildcard bits
tracked boolean	Match packets in existing ICMP/UDP/TCP connections Choices: `false` `true`
ttl dictionary	Compares the TTL (time-to-live) value in the packet to a specified value
eq integer	Match a single TTL value
gt integer	Match TTL greater than this number
lt integer	Match TTL lesser than this number
neq integer	Match TTL not equal to this value
vlan string	Vlan options
name string / required	Name of the acl-list
standard boolean	standard access-list or not Choices: `false` `true`
afi string / required	The Address Family Indicator (AFI) for the Access Control Lists (ACL). Choices: `"ipv4"` `"ipv6"`
running_config string	This option is used only with state parsed. The value of this option should be the output received from the EOS device by executing the command show running-config \| section access-list. The state parsed reads the configuration from `running_config` option and transforms it into Ansible structured data as per the resource module’s argspec and the value is then returned in the parsed key within the result.
state string	The state the configuration should be left in. Choices: `"deleted"` `"merged"` ← (default) `"overridden"` `"replaced"` `"gathered"` `"rendered"` `"parsed"`

Notes 

Note

Tested against Arista EOS 4.24.6F

Examples 

# Using merged

# Before state:
# -------------
# show running-config | section access-list
# ip access-list test1
#    10 permit ip 10.10.10.0/24 any ttl eq 200
#    20 permit ip 10.30.10.0/24 host 10.20.10.1
#    30 deny tcp host 10.10.20.1 eq finger www any syn log
#    40 permit ip any any
# ipv6 access-list test2
#     10 deny icmpv6 any any reject-route hop-limit eq 20

- name: Merge provided configuration with device configuration
  arista.eos.eos_acls:
    config:
      - afi: ipv4
        acls:
          - name: test1
            aces:
              - sequence: 35
                grant: deny
                protocol: ospf
                source:
                  subnet_address: 20.0.0.0/8
                destination:
                  any: true
    state: merged

# After state:
# ------------
#
# show running-config | section access-list
# ip access-list test1
#    10 permit ip 10.10.10.0/24 any ttl eq 200
#    20 permit ip 10.30.10.0/24 host 10.20.10.1
#    30 deny tcp host 10.10.20.1 eq finger www any syn log
#    35 deny ospf 20.0.0.0/8 any
#    40 permit ip any any
# ipv6 access-list test2
#     10 deny icmpv6 any any reject-route hop-limit eq 20

# Using merged

# Before state:
# -------------
# show running-config | section access-list
# ip access-list test1
#    10 permit ip 10.10.10.0/24 any ttl eq 200
#    20 permit ip 10.30.10.0/24 host 10.20.10.1
#    30 deny tcp host 10.10.20.1 eq finger www any syn log
#    40 permit ip any any
# ipv6 access-list test2
#     10 deny icmpv6 any any reject-route hop-limit eq 20

- name: Merge to update the given configuration with an existing ace
  arista.eos.eos_acls:
    config:
      - afi: ipv4
        acls:
          - name: test1
            aces:
              - sequence: 35
                log: true
                ttl:
                  eq: 33
    state: merged

# After state:
# ------------
#
# show running-config | section access-list
# ip access-list test1
#    10 permit ip 10.10.10.0/24 any ttl eq 200
#    20 permit ip 10.30.10.0/24 host 10.20.10.1
#    30 deny tcp host 10.10.20.1 eq finger www any syn log
#    35 deny ospf 20.0.0.0/8 any ttl eq 33 log
#    40 permit ip any any
# ipv6 access-list test2
#     10 deny icmpv6 any any reject-route hop-limit eq 20

# Using replaced

# Before state:
# -------------
# show running-config | section access-list
# ip access-list test1
#    10 permit ip 10.10.10.0/24 any ttl eq 200
#    20 permit ip 10.30.10.0/24 host 10.20.10.1
#    30 deny tcp host 10.10.20.1 eq finger www any syn log
#    40 permit ip any any
# !
# ip access-list test3
#    10 permit ip 35.33.0.0/16 any log
# !
# ipv6 access-list test2
#     10 deny icmpv6 any any reject-route hop-limit eq 20

- name: Replace device configuration with provided configuration
  arista.eos.eos_acls:
    config:
      - afi: ipv4
        acls:
          - name: test1
            aces:
              - sequence: 35
                grant: permit
                protocol: ospf
                source:
                  subnet_address: 20.0.0.0/8
                destination:
                  any: true
    state: replaced

# After state:
# ------------
#
# show running-config | section access-list
# ip access-list test1
#    35 permit ospf 20.0.0.0/8 any
# !
# ip access-list test3
#    10 permit ip 35.33.0.0/16 any log
# !
# ipv6 access-list test2
#     10 deny icmpv6 any any reject-route hop-limit eq 20

# Using overridden

# Before state:
# -------------
# show running-config | section access-list
# ip access-list test1
#    10 permit ip 10.10.10.0/24 any ttl eq 200
#    20 permit ip 10.30.10.0/24 host 10.20.10.1
#    30 deny tcp host 10.10.20.1 eq finger www any syn log
#    40 permit ip any any
# !
# ip access-list test3
#    10 permit ip 35.33.0.0/16 any log
# !
# ipv6 access-list test2
#     10 deny icmpv6 any any reject-route hop-limit eq 20


- name: override device configuration with  provided configuration
  arista.eos.eos_acls:
    config:
      - afi: ipv4
        acls:
          - name: test1
            aces:
              - sequence: 35
                grant: permit
                protocol: ospf
                source:
                  subnet_address: 20.0.0.0/8
                destination:
                  any: true
    state: overridden

# After state:
# ------------
#
# show running-config | section access-list
# ip access-list test1
#    35 permit ospf 20.0.0.0/8 any
# !

# Using deleted:

# Before state:
# -------------
# show running-config | section access-list
# ip access-list test1
#    10 permit ip 10.10.10.0/24 any ttl eq 200
#    20 permit ip 10.30.10.0/24 host 10.20.10.1
#    30 deny tcp host 10.10.20.1 eq finger www any syn log
#    40 permit ip any any
# ipv6 access-list test2
#     10 deny icmpv6 any any reject-route hop-limit eq 20

# !

- name: Delete provided configuration
  arista.eos.eos_acls:
    config:
      - afi: ipv4
        acls:
          - name: test1
    state: deleted

# After state:
# ------------
#
# show running-config | section access-list

# ipv6 access-list test2
#     10 deny icmpv6 any any reject-route hop-limit eq 20


# using gathered

# ip access-list test1
#    35 deny ospf 20.0.0.0/8 any
# ip access-list test2
#    40 permit vlan 55 0xE2 icmpv6 any any log

- name: Gather the existing configuration
  arista.eos.eos_acls:
    state: gathered

# returns:

#  arista.eos.eos_acls:
#    config:
#      - afi: "ipv4"
#        acls:
#          - name: test1
#            aces:
#            - sequence: 35
#              grant: "deny"
#              protocol: "ospf"
#              source:
#                subnet_address: 20.0.0.0/8
#              destination:
#                any: true
#      - afi: "ipv6"
#         acls:
#           - name: test2
#             aces:
#               - sequence: 40
#                 grant: "permit"
#                 vlan: "55 0xE2"
#                 protocol: "icmpv6"
#                 log: true
#                 source:
#                   any: true
#                 destination:
#                   any: true

# using rendered

- name: Delete provided configuration
  arista.eos.eos_acls:
    config:
      - afi: ipv4
        acls:
          - name: test1
            aces:
              - sequence: 35
                grant: deny
                protocol: ospf
                source:
                  subnet_address: 20.0.0.0/8
                destination:
                  any: true
      - afi: ipv6
        acls:
          - name: test2
            aces:
              - sequence: 40
                grant: permit
                vlan: 55 0xE2
                protocol: icmpv6
                log: true
                source:
                  any: true
                destination:
                  any: true
    state: rendered

# returns:

# ip access-list test1
#    35 deny ospf 20.0.0.0/8 any
# ip access-list test2
#    40 permit vlan 55 0xE2 icmpv6 any any log

# Using Parsed

# parsed_acls.cfg

# ipv6 access-list standard test2
#    10 permit any log
# !
# ip access-list test1
#    35 deny ospf 20.0.0.0/8 any
#    45 remark Run by ansible
#    55 permit tcp any any
# !

- name: parse configs
  arista.eos.eos_acls:
    running_config: "{{ lookup('file', './parsed_acls.cfg') }}"
    state: parsed

# returns
# "parsed": [
#         {
#             "acls": [
#                 {
#                     "aces": [
#                         {
#                             "destination": {
#                                 "any": true
#                             },
#                             "grant": "deny",
#                             "protocol": "ospf",
#                             "sequence": 35,
#                             "source": {
#                                 "subnet_address": "20.0.0.0/8"
#                             }
#                         },
#                         {
#                             "remark": "Run by ansible",
#                             "sequence": 45
#                         },
#                         {
#                             "destination": {
#                                 "any": true
#                             },
#                             "grant": "permit",
#                             "protocol": "tcp",
#                             "sequence": 55,
#                             "source": {
#                                 "any": true
#                             }
#                         }
#                     ],
#                     "name": "test1"
#                 }
#             ],
#             "afi": "ipv4"
#         },
#         {
#             "acls": [
#                 {
#                     "aces": [
#                         {
#                             "grant": "permit",
#                             "log": true,
#                             "sequence": 10,
#                             "source": {
#                                 "any": true
#                             }
#                         }
#                     ],
#                     "name": "test2",
#                     "standard": true
#                 }
#             ],
#             "afi": "ipv6"
#         }
#     ]

Return Values 

Common return values are documented here, the following are the fields unique to this module:

Key	Description
after list / elements=string	The resulting configuration model invocation. Returned: when changed Sample: `["The configuration returned will always be in the same format\n of the parameters above.\n"]`
before list / elements=string	The configuration prior to the model invocation. Returned: always Sample: `["The configuration returned will always be in the same format\n of the parameters above.\n"]`
commands list / elements=string	The set of commands pushed to the remote device. Returned: always Sample: `["ipv6 access-list standard test2", "10 permit any log", "ip access-list test1", "35 deny ospf 20.0.0.0/8 any", "45 remark Run by ansible", "55 permit tcp any any"]`

Authors

Gomathiselvi S (@GomathiselviS)

arista.eos.eos_acls module – ACLs resource module

Synopsis

Parameters

Notes

Examples

Return Values