junipernetworks.junos.junos_ospfv2 module – OSPFv2 resource module
Note
This module is part of the junipernetworks.junos collection (version 5.3.1).
You might already have this collection installed if you are using the ansible
package.
It is not included in ansible-core
.
To check whether it is installed, run ansible-galaxy collection list
.
To install it, use: ansible-galaxy collection install junipernetworks.junos
.
You need further requirements to be able to use this module,
see Requirements for details.
To use it in a playbook, specify: junipernetworks.junos.junos_ospfv2
.
New in junipernetworks.junos 1.0.0
Synopsis
This module manages OSPFv2 configuration on devices running Juniper JUNOS.
Note
This module has a corresponding action plugin.
Requirements
The below requirements are needed on the host that executes this module.
ncclient (>=v0.6.4)
xmltodict (>=0.12.0)
Parameters
Parameter |
Comments |
---|---|
A list of OSPFv2 process configuration. |
|
A list of OSPFv2 areas’ configuration. |
|
The Area ID as an integer or IP Address. |
|
Configure an address range for the area. Included for compatibility, remove/deprecate after 2025-07-01. Alternate for this would be area_ranges which is a list. |
|
Configure IP address ranges for the area. |
|
Specify ip address. |
|
Enforce exact match for advertisement of this area range. Choices:
|
|
Override the dynamic metric for this area-range. |
|
Restrict advertisement of this area range. Choices:
|
|
List of interfaces in this area. |
|
Specify authentication type |
|
MD5 authentication keys |
|
Specify key value |
|
Specify the key identity |
|
Specify Start time for key transmission (YYYY-MM-DD.HH:MM) |
|
Specify authentication key. |
|
Type of authentication to use. Included for compatibility, remove/deprecate after 2025-07-01. |
|
Specify list of bandwidth based metrics |
|
BW to apply metric to. Choices:
|
|
Specify metric |
|
Enable flood reduction. Choices:
|
|
Metric applied to the interface. |
|
Name of the interface. |
|
Specify passive Choices:
|
|
Priority for the interface. |
|
Specify timers |
|
Dead interval (seconds). |
|
Hello interval (seconds). |
|
Poll interval (seconds). |
|
Retransmit interval (seconds). |
|
Transit delay (seconds). |
|
Settings for configuring the area as a stub. |
|
Metric for the default route in this area. |
|
Configure the area as a stub. Choices:
|
|
Preference of external routes. |
|
Specify time for overload mode reset |
|
Allow routes to be leaked when overload is configured. Choices:
|
|
Advertise As External with maximum usable metric. Choices:
|
|
Advertise Stub Network with maximum metric. Choices:
|
|
Time after which overload mode is reset (seconds). |
|
Preference of internal routes. |
|
Maximum number of external prefixes that can be exported. |
|
Bandwidth for calculating metric defaults. Choices:
|
|
Set RFC1583 compatibility Choices:
|
|
The OSPFv2 router id. |
|
Configure options for SPF. |
|
Time to wait before running an SPF (seconds). |
|
Time to hold down before running an SPF (seconds). |
|
Do not ignore self-generated external and NSSA LSAs. Choices:
|
|
Number of maximum rapid SPF runs before holddown (seconds). |
|
This option is used only with state parsed. The value of this option should be the output received from the Junos device by executing the command show protocols ospf. The state parsed reads the configuration from |
|
The state the configuration should be left in. Choices:
|
Notes
Note
This module requires the netconf system service be enabled on the device being managed.
This module works with connection
netconf
.Tested against JunOS v18.4R1
Examples
# Using merged
#
# Before state
# ------------
#
# admin# show protocols ospf
- name: Merge provided OSPFv2 configuration into running config.
junipernetworks.junos.junos_ospfv2:
config:
- reference_bandwidth: 10g
areas:
- area_id: 0.0.0.100
area_ranges:
- address: 10.200.17.0/24
exact: true
restrict: true
override_metric: 2000
- address: 10.200.15.0/24
exact: true
restrict: true
override_metric: 2000
stub:
default_metric: 100
set: true
interfaces:
- name: so-0/0/0.0
priority: 3
metric: 5
flood_reduction: false
passive: true
bandwidth_based_metrics:
- bandwidth: 1g
metric: 5
- bandwidth: 10g
metric: 40
timers:
dead_interval: 4
hello_interval: 2
poll_interval: 2
retransmit_interval: 2
rfc1583compatibility: false
state: merged
# Task Output:
# ------------
#
# before: []
#
# commands:
# - <nc:protocols xmlns:nc="urn:ietf:params:xml:ns:netconf:base:1.0">
# <nc:ospf><nc:reference-bandwidth>10g</nc:reference-bandwidth><nc:no-rfc-1583/>
# <nc:area><nc:name>0.0.0.100</nc:name><nc:area-range><nc:name>10.200.17.0/24</nc:name><nc:exact/>
# <nc:restrict/><nc:override-metric>2000</nc:override-metric></nc:area-range><nc:area-range>
# <nc:name>10.200.15.0/24</nc:name><nc:exact/><nc:restrict/><nc:override-metric>2000</nc:override-metric>
# </nc:area-range><nc:interface><nc:name>so-0/0/0.0</nc:name><nc:priority>3</nc:priority>
# <nc:metric>5</nc:metric><nc:passive/><nc:bandwidth-based-metrics><nc:bandwidth><nc:name>1g</nc:name>
# <nc:metric>5</nc:metric></nc:bandwidth><nc:bandwidth><nc:name>10g</nc:name><nc:metric>40</nc:metric>
# </nc:bandwidth></nc:bandwidth-based-metrics><nc:dead-interval>4</nc:dead-interval>
# <nc:hello-interval>2</nc:hello-interval><nc:poll-interval>2</nc:poll-interval>
# <nc:retransmit-interval>2</nc:retransmit-interval></nc:interface><nc:stub>
# <nc:default-metric>100</nc:default-metric></nc:stub></nc:area></nc:ospf></nc:protocols>
#
# after:
# - areas:
# - area_id: 0.0.0.100
# area_range: '[''10.200.17.0/24'', ''10.200.15.0/24'']'
# area_ranges:
# - address: 10.200.17.0/24
# exact: true
# override_metric: 2000
# restrict: true
# - address: 10.200.15.0/24
# exact: true
# override_metric: 2000
# restrict: true
# interfaces:
# - bandwidth_based_metrics:
# - bandwidth: 1g
# metric: 5
# - bandwidth: 10g
# metric: 40
# metric: 5
# name: so-0/0/0.0
# passive: true
# priority: 3
# timers:
# dead_interval: 4
# hello_interval: 2
# poll_interval: 2
# retransmit_interval: 2
# stub:
# default_metric: 100
# set: true
# reference_bandwidth: 10g
# rfc1583compatibility: false
# After state
# -----------
#
# admin# show protocols ospf
# reference-bandwidth 10g;
# no-rfc-1583;
# area 0.0.0.100 {
# stub default-metric 100;
# area-range 10.200.17.0/24 {
# restrict;
# exact;
# override-metric 2000;
# }
# area-range 10.200.15.0/24 {
# restrict;
# exact;
# override-metric 2000;
# }
# interface so-0/0/0.0 {
# passive;
# bandwidth-based-metrics {
# bandwidth 1g metric 5;
# bandwidth 10g metric 40;
# }
# metric 5;
# priority 3;
# retransmit-interval 2;
# hello-interval 2;
# dead-interval 4;
# poll-interval 2;
# }
# }
#
# Using replaced
#
# Before state
# ------------
#
# admin# show protocols ospf
# reference-bandwidth 10g;
# no-rfc-1583;
# area 0.0.0.100 {
# stub default-metric 100;
# area-range 10.200.17.0/24 {
# restrict;
# exact;
# override-metric 2000;
# }
# area-range 10.200.15.0/24 {
# restrict;
# exact;
# override-metric 2000;
# }
# interface so-0/0/0.0 {
# passive;
# bandwidth-based-metrics {
# bandwidth 1g metric 5;
# bandwidth 10g metric 40;
# }
# metric 5;
# priority 3;
# retransmit-interval 2;
# hello-interval 2;
# dead-interval 4;
# poll-interval 2;
# }
# }
- name: Replace existing Junos OSPFv2 config with provided config
junipernetworks.junos.junos_ospfv2:
config:
- reference_bandwidth: 10g
areas:
- area_id: 0.0.0.100
area_ranges:
- address: 10.200.17.0/24
exact: true
restrict: true
- address: 10.200.16.0/24
exact: true
restrict: true
override_metric: 1000
stub:
default_metric: 100
set: true
interfaces:
- name: so-0/0/0.0
priority: 3
metric: 5
flood_reduction: false
passive: true
bandwidth_based_metrics:
- bandwidth: 1g
metric: 5
- bandwidth: 10g
metric: 40
timers:
dead_interval: 4
hello_interval: 2
poll_interval: 2
retransmit_interval: 2
rfc1583compatibility: false
state: replacedd
# Task Output:
# ------------
#
# before:
# - areas:
# - area_id: 0.0.0.100
# area_range: '[''10.200.17.0/24'', ''10.200.15.0/24'']'
# area_ranges:
# - address: 10.200.17.0/24
# exact: true
# override_metric: 2000
# restrict: true
# - address: 10.200.15.0/24
# exact: true
# override_metric: 2000
# restrict: true
# interfaces:
# - bandwidth_based_metrics:
# - bandwidth: 1g
# metric: 5
# - bandwidth: 10g
# metric: 40
# metric: 5
# name: so-0/0/0.0
# passive: true
# priority: 3
# timers:
# dead_interval: 4
# hello_interval: 2
# poll_interval: 2
# retransmit_interval: 2
# stub:
# default_metric: 100
# set: true
# reference_bandwidth: 10g
# rfc1583compatibility: false
#
# commands:
# - <nc:protocols xmlns:nc="urn:ietf:params:xml:ns:netconf:base:1.0">
# <nc:ospf><nc:area delete="delete">0.0.0.100</nc:area></nc:ospf><nc:ospf>
# <nc:reference-bandwidth>10g</nc:reference-bandwidth><nc:no-rfc-1583/><nc:area>
# <nc:name>0.0.0.100</nc:name><nc:area-range><nc:name>10.200.17.0/24</nc:name><nc:exact/>
# <nc:restrict/></nc:area-range><nc:area-range><nc:name>10.200.16.0/24</nc:name><nc:exact/>
# <nc:restrict/><nc:override-metric>1000</nc:override-metric></nc:area-range><nc:interface>
# <nc:name>so-0/0/0.0</nc:name><nc:priority>3</nc:priority><nc:metric>5</nc:metric><nc:passive/>
# <nc:bandwidth-based-metrics><nc:bandwidth><nc:name>1g</nc:name><nc:metric>5</nc:metric>
# </nc:bandwidth><nc:bandwidth><nc:name>10g</nc:name><nc:metric>40</nc:metric></nc:bandwidth>
# </nc:bandwidth-based-metrics><nc:dead-interval>4</nc:dead-interval><nc:hello-interval>2</nc:hello-interval>
# <nc:poll-interval>2</nc:poll-interval><nc:retransmit-interval>2</nc:retransmit-interval></nc:interface>
# <nc:stub><nc:default-metric>100</nc:default-metric></nc:stub></nc:area></nc:ospf></nc:protocols>
#
# after:
# - areas:
# - area_id: 0.0.0.100
# area_range: '[''10.200.17.0/24'', ''10.200.16.0/24'']'
# area_ranges:
# - address: 10.200.17.0/24
# exact: true
# restrict: true
# - address: 10.200.16.0/24
# exact: true
# override_metric: 1000
# restrict: true
# interfaces:
# - bandwidth_based_metrics:
# - bandwidth: 1g
# metric: 5
# - bandwidth: 10g
# metric: 40
# metric: 5
# name: so-0/0/0.0
# passive: true
# priority: 3
# timers:
# dead_interval: 4
# hello_interval: 2
# poll_interval: 2
# retransmit_interval: 2
# stub:
# default_metric: 100
# set: true
# reference_bandwidth: 10g
# rfc1583compatibility: false
#
# After state
# -----------
#
# admin# show protocols ospf
# reference-bandwidth 10g;
# no-rfc-1583;
# area 0.0.0.100 {
# stub default-metric 100;
# area-range 10.200.17.0/24 {
# restrict;
# exact;
# }
# area-range 10.200.16.0/24 {
# restrict;
# exact;
# override-metric 1000;
# }
# interface so-0/0/0.0 {
# passive;
# bandwidth-based-metrics {
# bandwidth 1g metric 5;
# bandwidth 10g metric 40;
# }
# metric 5;
# priority 3;
# retransmit-interval 2;
# hello-interval 2;
# dead-interval 4;
# poll-interval 2;
# }
# }
#
# Using overridden
#
# Before state
# ------------
#
# admin# show protocols ospf
# reference-bandwidth 10g;
# no-rfc-1583;
# area 0.0.0.100 {
# stub default-metric 100;
# area-range 10.200.17.0/24 {
# restrict;
# exact;
# }
# area-range 10.200.16.0/24 {
# restrict;
# exact;
# override-metric 1000;
# }
# interface so-0/0/0.0 {
# passive;
# bandwidth-based-metrics {
# bandwidth 1g metric 5;
# bandwidth 10g metric 40;
# }
# metric 5;
# priority 3;
# retransmit-interval 2;
# hello-interval 2;
# dead-interval 4;
# poll-interval 2;
# }
# }
- name: Override runnig OSPFv2 config with provided config
junipernetworks.junos.junos_ospfv2:
config:
- reference_bandwidth: 10g
areas:
- area_id: 0.0.0.110
area_ranges:
- address: 20.200.17.0/24
exact: true
restrict: true
override_metric: 2000
- address: 20.200.15.0/24
exact: true
restrict: true
override_metric: 2000
stub:
default_metric: 200
set: true
interfaces:
- name: so-0/0/0.0
priority: 3
metric: 5
flood_reduction: false
passive: true
bandwidth_based_metrics:
- bandwidth: 1g
metric: 5
- bandwidth: 10g
metric: 40
state: overridden
# Task Output:
# ------------
#
# before:
# - areas:
# - area_id: 0.0.0.100
# area_range: '[''10.200.17.0/24'', ''10.200.16.0/24'']'
# area_ranges:
# - address: 10.200.17.0/24
# exact: true
# restrict: true
# - address: 10.200.16.0/24
# exact: true
# override_metric: 1000
# restrict: true
# interfaces:
# - bandwidth_based_metrics:
# - bandwidth: 1g
# metric: 5
# - bandwidth: 10g
# metric: 40
# metric: 5
# name: so-0/0/0.0
# passive: true
# priority: 3
# timers:
# dead_interval: 4
# hello_interval: 2
# poll_interval: 2
# retransmit_interval: 2
# stub:
# default_metric: 100
# set: true
# reference_bandwidth: 10g
# rfc1583compatibility: false
#
# commands:
# - <nc:protocols xmlns:nc="urn:ietf:params:xml:ns:netconf:base:1.0">
# <nc:ospf><nc:area delete="delete">0.0.0.100</nc:area></nc:ospf><nc:ospf>
# <nc:reference-bandwidth>10g</nc:reference-bandwidth><nc:area><nc:name>0.0.0.110</nc:name>
# <nc:area-range><nc:name>20.200.17.0/24</nc:name><nc:exact/><nc:restrict/>
# <nc:override-metric>2000</nc:override-metric></nc:area-range><nc:area-range>
# <nc:name>20.200.15.0/24</nc:name><nc:exact/><nc:restrict/><nc:override-metric>2000</nc:override-metric>
# </nc:area-range><nc:interface><nc:name>so-0/0/0.0</nc:name><nc:priority>3</nc:priority>
# <nc:metric>5</nc:metric><nc:passive/><nc:bandwidth-based-metrics><nc:bandwidth><nc:name>1g</nc:name>
# <nc:metric>5</nc:metric></nc:bandwidth><nc:bandwidth><nc:name>10g</nc:name><nc:metric>40</nc:metric>
# </nc:bandwidth></nc:bandwidth-based-metrics></nc:interface><nc:stub>
# <nc:default-metric>200</nc:default-metric></nc:stub></nc:area></nc:ospf></nc:protocols>
#
# after:
# - areas:
# - area_id: 0.0.0.110
# area_range: '[''20.200.17.0/24'', ''20.200.15.0/24'']'
# area_ranges:
# - address: 20.200.17.0/24
# exact: true
# override_metric: 2000
# restrict: true
# - address: 20.200.15.0/24
# exact: true
# override_metric: 2000
# restrict: true
# interfaces:
# - bandwidth_based_metrics:
# - bandwidth: 1g
# metric: 5
# - bandwidth: 10g
# metric: 40
# metric: 5
# name: so-0/0/0.0
# passive: true
# priority: 3
# stub:
# default_metric: 200
# set: true
# reference_bandwidth: 10g
# rfc1583compatibility: false
# After state
# -----------
#
# admin# show protocols ospf
# reference-bandwidth 10g;
# no-rfc-1583;
# area 0.0.0.110 {
# stub default-metric 200;
# area-range 20.200.17.0/24 {
# restrict;
# exact;
# override-metric 2000;
# }
# area-range 20.200.15.0/24 {
# restrict;
# exact;
# override-metric 2000;
# }
# interface so-0/0/0.0 {
# passive;
# bandwidth-based-metrics {
# bandwidth 1g metric 5;
# bandwidth 10g metric 40;
# }
# metric 5;
# priority 3;
# }
# }
# Using deleted
#
# Before state
# ------------
#
# admin# show protocols ospf
# reference-bandwidth 10g;
# no-rfc-1583;
# area 0.0.0.110 {
# stub default-metric 200;
# area-range 20.200.17.0/24 {
# restrict;
# exact;
# override-metric 2000;
# }
# area-range 20.200.15.0/24 {
# restrict;
# exact;
# override-metric 2000;
# }
# interface so-0/0/0.0 {
# passive;
# bandwidth-based-metrics {
# bandwidth 1g metric 5;
# bandwidth 10g metric 40;
# }
# metric 5;
# priority 3;
# }
# }
- name: Delete OSPFv2 running config.
junipernetworks.junos.junos_ospfv2:
config:
state: deleted
# Task Output:
# ------------
#
# before:
# - areas:
# - area_id: 0.0.0.110
# area_range: '[''20.200.17.0/24'', ''20.200.15.0/24'']'
# area_ranges:
# - address: 20.200.17.0/24
# exact: true
# override_metric: 2000
# restrict: true
# - address: 20.200.15.0/24
# exact: true
# override_metric: 2000
# restrict: true
# interfaces:
# - bandwidth_based_metrics:
# - bandwidth: 1g
# metric: 5
# - bandwidth: 10g
# metric: 40
# metric: 5
# name: so-0/0/0.0
# passive: true
# priority: 3
# stub:
# default_metric: 200
# set: true
# reference_bandwidth: 10g
# rfc1583compatibility: false
#
# commands:
# - <nc:protocols xmlns:nc="urn:ietf:params:xml:ns:netconf:base:1.0">
# <nc:ospf><nc:area delete="delete">0.0.0.100</nc:area><nc:reference-bandwidth delete="delete"/>
# <nc:no-rfc-1583 delete="delete"/></nc:ospf></nc:protocols>
#
# after: []
#
#
# After state
# -----------
#
# admin# show protocols ospf
# Using gathered
#
# Before state
# ------------
#
# admin# show protocols ospf
# reference-bandwidth 10g;
# no-rfc-1583;
# area 0.0.0.100 {
# stub default-metric 100;
# area-range 10.200.17.0/24 {
# restrict;
# exact;
# override-metric 2000;
# }
# area-range 10.200.15.0/24 {
# restrict;
# exact;
# override-metric 2000;
# }
# interface so-0/0/0.0 {
# passive;
# bandwidth-based-metrics {
# bandwidth 1g metric 5;
# bandwidth 10g metric 40;
# }
# metric 5;
# priority 3;
# retransmit-interval 2;
# hello-interval 2;
# dead-interval 4;
# poll-interval 2;
# }
# }
- name: Gather Junos OSPFv2 running-configuration
junipernetworks.junos.junos_ospfv2:
config:
state: gathered
#
#
# Task Output:
# ------------
#
# gathered:
#
# - areas:
# - area_id: 0.0.0.100
# area_range: '[''10.200.17.0/24'', ''10.200.15.0/24'']'
# area_ranges:
# - address: 10.200.17.0/24
# exact: true
# override_metric: 2000
# restrict: true
# - address: 10.200.15.0/24
# exact: true
# override_metric: 2000
# restrict: true
# interfaces:
# - bandwidth_based_metrics:
# - bandwidth: 1g
# metric: 5
# - bandwidth: 10g
# metric: 40
# metric: 5
# name: so-0/0/0.0
# passive: true
# priority: 3
# timers:
# dead_interval: 4
# hello_interval: 2
# poll_interval: 2
# retransmit_interval: 2
# stub:
# default_metric: 100
# set: true
# reference_bandwidth: 10g
# rfc1583compatibility: false
# Using parsed
# parsed.cfg
# ------------
# <?xml version="1.0" encoding="UTF-8"?>
# <rpc-reply message-id="urn:uuid:0cadb4e8-5bba-47f4-986e-72906227007f">
# <configuration changed-seconds="1590139550" changed-localtime="2020-05-22 09:25:50 UTC">
# <version>18.4R1-S2.4</version>
# <protocols>
# <ospf>
# <reference-bandwidth>10g</reference-bandwidth>
# <no-rfc-1583/>
# <area>
# <name>0.0.0.100</name>
# <stub>
# <default-metric>100</default-metric>
# </stub>
# <area-range>
# <name>10.200.16.0/24</name>
# <exact/>
# <override-metric>10000</override-metric>
# </area-range>
# <area-range>
# <name>10.200.11.0/24</name>
# <restrict/>
# <exact/>
# </area-range>
# <interface>
# <name>so-0/0/0.0</name>
# <passive>
# </passive>
# <bandwidth-based-metrics>
# <bandwidth>
# <name>1g</name>
# <metric>5</metric>
# </bandwidth>
# <bandwidth>
# <name>10g</name>
# <metric>40</metric>
# </bandwidth>
# </bandwidth-based-metrics>
# <metric>5</metric>
# <priority>3</priority>
# <retransmit-interval>2</retransmit-interval>
# <hello-interval>2</hello-interval>
# <dead-interval>4</dead-interval>
# <poll-interval>2</poll-interval>
# </interface>
# </area>
# </ospf>
# </protocols>
# <routing-options>
# <static>
# <route>
# <name>172.16.17.0/24</name>
# <discard />
# </route>
# </static>
# <router-id>10.200.16.75</router-id>
# <autonomous-system>
# <as-number>65432</as-number>
# </autonomous-system>
# </routing-options>
# </configuration>
# </rpc-reply>
- name: Parsed the ospfv2 config into structured ansible resource facts.
junipernetworks.junos.junos_ospfv2:
running_config: "{{ lookup('file', './parsed.cfg') }}"
state: parsed
#
# Task Output:
# ------------
#
# parsed:
# - areas:
# - area_id: 0.0.0.100
# area_range: '[''10.200.16.0/24'', ''10.200.11.0/24'']'
# area_ranges:
# - address: 10.200.16.0/24
# exact: true
# override_metric: 10000
# - address: 10.200.11.0/24
# exact: true
# restrict: true
# interfaces:
# - bandwidth_based_metrics:
# - bandwidth: 1g
# metric: 5
# - bandwidth: 10g
# metric: 40
# metric: 5
# name: so-0/0/0.0
# passive: true
# priority: 3
# timers:
# dead_interval: 4
# hello_interval: 2
# poll_interval: 2
# retransmit_interval: 2
# stub:
# default_metric: 100
# set: true
# reference_bandwidth: 10g
# rfc1583compatibility: false
# router_id: 10.200.16.75
# Using rendered
#
- name: Render the commands for provided configuration
junipernetworks.junos.junos_ospfv2:
config:
- reference_bandwidth: 10g
areas:
- area_id: 0.0.0.100
area_ranges:
- address: 10.200.17.0/24
exact: true
restrict: true
override_metric: 2000
- address: 10.200.15.0/24
exact: true
restrict: true
override_metric: 2000
stub:
default_metric: 100
set: true
interfaces:
- name: so-0/0/0.0
priority: 3
metric: 5
flood_reduction: false
passive: true
bandwidth_based_metrics:
- bandwidth: 1g
metric: 5
- bandwidth: 10g
metric: 40
timers:
dead_interval: 4
hello_interval: 2
poll_interval: 2
retransmit_interval: 2
rfc1583compatibility: false
state: rendered
# Task Output:
# ------------
#
# rendered: "<nc:protocols xmlns:nc="urn:ietf:params:xml:ns:netconf:base:1.0">
# <nc:ospf><nc:reference-bandwidth>10g</nc:reference-bandwidth><nc:no-rfc-1583/><nc:area><nc:name>0.0.0.100</nc:name>
# <nc:area-range><nc:name>10.200.17.0/24</nc:name><nc:exact/><nc:restrict/><nc:override-metric>2000</nc:override-metric>
# </nc:area-range><nc:area-range><nc:name>10.200.15.0/24</nc:name><nc:exact/><nc:restrict/>
# <nc:override-metric>2000</nc:override-metric></nc:area-range><nc:interface><nc:name>so-0/0/0.0</nc:name>
# <nc:priority>3</nc:priority><nc:metric>5</nc:metric><nc:passive/><nc:bandwidth-based-metrics><nc:bandwidth>
# <nc:name>1g</nc:name><nc:metric>5</nc:metric></nc:bandwidth><nc:bandwidth><nc:name>10g</nc:name>
# <nc:metric>40</nc:metric></nc:bandwidth></nc:bandwidth-based-metrics><nc:dead-interval>4</nc:dead-interval>
# <nc:hello-interval>2</nc:hello-interval><nc:poll-interval>2</nc:poll-interval>
# <nc:retransmit-interval>2</nc:retransmit-interval></nc:interface><nc:stub>
# <nc:default-metric>100</nc:default-metric></nc:stub></nc:area></nc:ospf></nc:protocols>"
Return Values
Common return values are documented here, the following are the fields unique to this module:
Key |
Description |
---|---|
The resulting configuration module invocation. Returned: when changed Sample: |
|
The configuration prior to the module invocation. Returned: always Sample: |
|
The set of commands pushed to the remote device. Returned: always Sample: |
|
Facts about the network resource gathered from the remote device as structured data. Returned: when state is Sample: |
|
The device native config provided in running_config option parsed into structured data as per module argspec. Returned: when state is Sample: |
|
The provided configuration in the task rendered in device-native format (offline). Returned: when state is Sample: |