cisco.nxos.nxos_ospfv3 module – OSPFv3 resource module

Note

This module is part of the cisco.nxos collection (version 7.0.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install cisco.nxos.

To use it in a playbook, specify: cisco.nxos.nxos_ospfv3.

New in cisco.nxos 1.2.0

Synopsis

• This module manages OSPFv3 configuration on devices running Cisco NX-OS.

Aliases: ospfv3

Parameters

Parameter	Comments
config dictionary	A list of OSPFv3 process configuration.
processes list / elements=dictionary	A list of OSPFv3 instances’ configurations.
address_family dictionary	IPv6 unicast address-family OSPFv3 settings.
afi string	Configure OSPFv3 settings under IPv6 address-family. Choices: "ipv6"
areas list / elements=dictionary	Configure properties of OSPF Areas under address-family.
area_id string / required	The Area ID in IP Address format.
default_cost integer	Specify the default cost.
filter_list list / elements=dictionary	Filter prefixes between OSPF areas.
direction string / required	The direction to apply the route map. Choices: "in" "out"
route_map string / required	The Route-map name.
ranges list / elements=dictionary	Configure an address range for the area.
cost integer	Cost to use for the range.
not_advertise boolean	Suppress advertising the specified range. Choices: false true
prefix string / required	IP in Prefix format (x.x.x.x/len)
default_information dictionary	Control distribution of default routes.
originate dictionary	Distribute a default route.
always boolean	Always advertise a default route. Choices: false true
route_map string	Policy to control distribution of default routes
set boolean	Enable distribution of default route. Choices: false true
distance integer	Configure the OSPF administrative distance.
maximum_paths integer	Maximum paths per destination.
redistribute list / elements=dictionary	Redistribute information from another routing protocol.
id string	The identifier for the protocol specified.
protocol string / required	The name of the protocol. Choices: "bgp" "direct" "eigrp" "isis" "lisp" "ospfv3" "rip" "static"
route_map string / required	The route map policy to constrain redistribution.
safi string	Configure OSPFv3 settings under IPv6 unicast address-family. Choices: "unicast"
summary_address list / elements=dictionary	Configure route summarization for redistribution.
not_advertise boolean	Suppress advertising the specified summary. Choices: false true
prefix string / required	IPv6 prefix format ‘xxxx:xxxx/ml’, ‘xxxx:xxxx::/ml’ or ‘xxxx::xx/128’
tag integer	A 32-bit tag value.
table_map dictionary	Policy for filtering/modifying OSPF routes before sending them to RIB.
filter boolean	Block the OSPF routes from being sent to RIB. Choices: false true
name string / required	The Route Map name.
timers dictionary	Configure timer related constants.
throttle dictionary	Configure throttle related constants.
spf dictionary	Set OSPF SPF timers.
initial_spf_delay integer	Initial SPF schedule delay in milliseconds.
max_wait_time integer	Maximum wait time between SPF calculations.
min_hold_time integer	Minimum hold time between SPF calculations.
areas list / elements=dictionary	Configure properties of OSPF Areas.
area_id string / required	The Area ID in IP Address format.
nssa dictionary	NSSA settings for the area.
default_information_originate boolean	Originate Type-7 default LSA into NSSA area. Choices: false true
no_redistribution boolean	Do not send redistributed LSAs into NSSA area. Choices: false true
no_summary boolean	Do not send summary LSAs into NSSA area. Choices: false true
route_map string	Policy to control distribution of default route.
set boolean	Configure area as NSSA. Choices: false true
translate dictionary	Translate LSA.
type7 dictionary	Translate from Type 7 to Type 5.
always boolean	Always translate LSAs Choices: false true
never boolean	Never translate LSAs Choices: false true
supress_fa boolean	Suppress forwarding address in translated LSAs. Choices: false true
stub dictionary	Settings for configuring the area as a stub.
no_summary boolean	Prevent ABR from sending summary LSAs into stub area. Choices: false true
set boolean	Configure the area as a stub. Choices: false true
auto_cost dictionary	Calculate OSPF cost according to bandwidth.
reference_bandwidth integer / required	Reference bandwidth used to assign OSPF cost.
unit string / required	Specify in which unit the reference bandwidth is specified. Choices: "Gbps" "Mbps"
flush_routes boolean	Flush routes on a non-graceful controlled restart. Choices: false true
graceful_restart dictionary	Configure graceful restart.
grace_period integer	Configure maximum interval to restart gracefully.
helper_disable boolean	Enable/Disable helper mode. Choices: false true
planned_only boolean	Enable graceful restart only for a planned restart Choices: false true
set boolean	Enable graceful-restart. Choices: false true
isolate boolean	Isolate this router from OSPF perspective. Choices: false true
log_adjacency_changes dictionary	Log changes in adjacency state.
detail boolean	Notify all state changes. Choices: false true
log boolean	Enable/disable logging changes in adjacency state. Choices: false true
max_lsa dictionary	Feature to limit the number of non-self-originated LSAs.
ignore_count integer	Set count on how many times adjacencies can be suppressed.
ignore_time integer	Set time during which all adjacencies are suppressed.
max_non_self_generated_lsa integer / required	Set the maximum number of non self-generated LSAs.
reset_time integer	Set number of minutes after which ignore-count is reset to zero.
threshold integer	Threshold value (%) at which to generate a warning message.
warning_only boolean	Log a warning message when limit is exceeded. Choices: false true
max_metric dictionary	Maximize the cost metric.
router_lsa dictionary	Router LSA configuration.
external_lsa dictionary	External LSA configuration.
max_metric_value integer	Set max metric value for external LSAs.
set boolean	Set external-lsa attribute. Choices: false true
inter_area_prefix_lsa dictionary	Inter-area-prefix LSAs configuration.
max_metric_value integer	Max metric value for summary LSAs.
set boolean	Set summary-lsa attribute. Choices: false true
on_startup dictionary	Effective only at startup.
set boolean	Set on-startup attribute. Choices: false true
wait_for_bgp_asn integer	ASN of BGP to wait for.
wait_period integer	Wait period in seconds after startup.
set boolean	Set router-lsa attribute. Choices: false true
stub_prefix_lsa boolean	Advertise Max metric for Stub links as well. Choices: false true
name_lookup boolean	Display OSPF router ids as DNS names. Choices: false true
passive_interface dictionary	Suppress routing updates on the interface.
default boolean	Interfaces passive by default. Choices: false true
process_id string / required	The OSPF process tag.
router_id string	Set OSPF process router-id.
shutdown boolean	Shutdown the OSPF protocol instance. Choices: false true
timers dictionary	Configure timer related constants.
lsa_arrival integer	Mimimum interval between arrival of a LSA.
lsa_group_pacing integer	LSA group refresh/maxage interval.
throttle dictionary	Configure throttle related constants.
lsa dictionary	Set rate-limiting for LSA generation.
hold_interval integer	The hold interval.
max_interval integer	The max interval.
start_interval integer	The start interval.
vrfs list / elements=dictionary	Configure VRF specific OSPF settings.
areas list / elements=dictionary	Configure properties of OSPF Areas.
area_id string / required	The Area ID in IP Address format.
nssa dictionary	NSSA settings for the area.
default_information_originate boolean	Originate Type-7 default LSA into NSSA area. Choices: false true
no_redistribution boolean	Do not send redistributed LSAs into NSSA area. Choices: false true
no_summary boolean	Do not send summary LSAs into NSSA area. Choices: false true
route_map string	Policy to control distribution of default route.
set boolean	Configure area as NSSA. Choices: false true
translate dictionary	Translate LSA.
type7 dictionary	Translate from Type 7 to Type 5.
always boolean	Always translate LSAs Choices: false true
never boolean	Never translate LSAs Choices: false true
supress_fa boolean	Suppress forwarding address in translated LSAs. Choices: false true
stub dictionary	Settings for configuring the area as a stub.
no_summary boolean	Prevent ABR from sending summary LSAs into stub area. Choices: false true
set boolean	Configure the area as a stub. Choices: false true
auto_cost dictionary	Calculate OSPF cost according to bandwidth.
reference_bandwidth integer / required	Reference bandwidth used to assign OSPF cost.
unit string / required	Specify in which unit the reference bandwidth is specified. Choices: "Gbps" "Mbps"
graceful_restart dictionary	Configure graceful restart.
grace_period integer	Configure maximum interval to restart gracefully.
helper_disable boolean	Enable/Disable helper mode. Choices: false true
planned_only boolean	Enable graceful restart only for a planned restart Choices: false true
set boolean	Enable graceful-restart. Choices: false true
log_adjacency_changes dictionary	Log changes in adjacency state.
detail boolean	Notify all state changes. Choices: false true
log boolean	Enable/disable logging changes in adjacency state. Choices: false true
max_lsa dictionary	Feature to limit the number of non-self-originated LSAs.
ignore_count integer	Set count on how many times adjacencies can be suppressed.
ignore_time integer	Set time during which all adjacencies are suppressed.
max_non_self_generated_lsa integer / required	Set the maximum number of non self-generated LSAs.
reset_time integer	Set number of minutes after which ignore-count is reset to zero.
threshold integer	Threshold value (%) at which to generate a warning message.
warning_only boolean	Log a warning message when limit is exceeded. Choices: false true
max_metric dictionary	Maximize the cost metric.
router_lsa dictionary	Router LSA configuration.
external_lsa dictionary	External LSA configuration.
max_metric_value integer	Set max metric value for external LSAs.
set boolean	Set external-lsa attribute. Choices: false true
inter_area_prefix_lsa dictionary	Inter-area-prefix LSAs configuration.
max_metric_value integer	Max metric value for summary LSAs.
set boolean	Set summary-lsa attribute. Choices: false true
on_startup dictionary	Effective only at startup.
set boolean	Set on-startup attribute. Choices: false true
wait_for_bgp_asn integer	ASN of BGP to wait for.
wait_period integer	Wait period in seconds after startup.
set boolean	Set router-lsa attribute. Choices: false true
stub_prefix_lsa boolean	Advertise Max metric for Stub links as well. Choices: false true
name_lookup boolean	Display OSPF router ids as DNS names. Choices: false true
passive_interface dictionary	Suppress routing updates on the interface.
default boolean	Interfaces passive by default. Choices: false true
router_id string	Set OSPF process router-id.
shutdown boolean	Shutdown the OSPF protocol instance. Choices: false true
timers dictionary	Configure timer related constants.
lsa_arrival integer	Mimimum interval between arrival of a LSA.
lsa_group_pacing integer	LSA group refresh/maxage interval.
throttle dictionary	Configure throttle related constants.
lsa dictionary	Set rate-limiting for LSA generation.
hold_interval integer	The hold interval.
max_interval integer	The max interval.
start_interval integer	The start interval.
vrf string / required	Name/Identifier of the VRF.
running_config string	This option is used only with state parsed. The value of this option should be the output received from the NX-OS device by executing the command show running-config | section “^router ospfv3”. The state parsed reads the configuration from running_config option and transforms it into Ansible structured data as per the resource module’s argspec and the value is then returned in the parsed key within the result.
state string	The state the configuration should be left in. Choices: "merged" ← (default) "replaced" "overridden" "deleted" "gathered" "parsed" "rendered"

Notes

Note

• Tested against NX-OS 7.0(3)I5(1).

• Unsupported for Cisco MDS

• This module works with connection network_cli and httpapi.

Examples

# Using merged

# Before state:
# -------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# nxos-9k-rdo#

- name: Merge the provided configuration with the existing running configuration
  cisco.nxos.nxos_ospfv3:
    config:
      processes:
        - process_id: 100
          router_id: 203.0.113.20
        - process_id: 102
          router_id: 198.51.100.1
          address_family:
            afi: ipv6
            safi: unicast
            areas:
              - area_id: 0.0.0.100
                filter_list:
                  - route_map: rmap_1
                    direction: in
                  - route_map: rmap_2
                    direction: out
                ranges:
                  - prefix: '2001:db2::/32'
                    not_advertise: true
                  - prefix: '2001:db3::/32'
                    cost: 120
            redistribute:
              - protocol: eigrp
                id: 120
                route_map: rmap_1
              - protocol: direct
                route_map: ospf102-direct-connect
          vrfs:
            - vrf: zone1
              router_id: 198.51.100.129
              areas:
                - area_id: 0.0.0.102
                  nssa:
                    default_information_originate: true
                    no_summary: true
                - area_id: 0.0.0.103
                  nssa:
                    no_summary: true
                    translate:
                      type7:
                        always: true
            - vrf: zone2
              auto_cost:
                reference_bandwidth: 45
                unit: Gbps
    state: merged

# Task output:
# ------------
# before: {}
#
# commands:
#  - router ospf 102
#  - router-id 198.51.100.1
#  - address-family ipv6 unicast
#  - redistribute eigrp 120 route-map rmap_1
#  - redistribute direct route-map ospf102-direct-connect
#  - area 0.0.0.100 filter-list route-map rmap_1 in
#  - area 0.0.0.100 filter-list route-map rmap_2 out
#  - area 0.0.0.100 range 2001:db2::/32 not-advertise
#  - area 0.0.0.100 range 2001:db3::/32 cost 120
#  - vrf zone1
#  - router-id 198.51.100.129
#  - area 0.0.0.102 nssa no-summary default-information-originate
#  - area 0.0.0.103 nssa no-summary
#  - area 0.0.0.103 nssa translate type7 always
#  - vrf zone2
#  - auto-cost reference-bandwidth 45 Gbps
#  - router ospf 100
#  - router-id 203.0.113.20
#
# after:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv4
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: out
#            route_map: rmap_2
#          - direction: in
#            route_map: rmap_1
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#          - cost: 120
#            prefix: 2001:db3::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "120"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
#   router-id 203.0.113.20
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family ipv6 unicast
#     redistribute direct route-map ospf102-direct-connect
#     redistribute eigrp 120 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_2 out
#     area 0.0.0.100 filter-list route-map rmap_1 in
#     area 0.0.0.100 range 2001:db2::/32 not-advertise
#     area 0.0.0.100 range 2001:db3::/32 cost 120
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

# Using replaced

# Before state:
# -------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
#   router-id 203.0.113.20
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family upv6 unicast
#     redistribute direct route-map ospf102-direct-connect
#     redistribute eigrp 120 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_2 out
#     area 0.0.0.100 filter-list route-map rmap_1 in
#     area 0.0.0.100 range 2001:db2::/32 not-advertise
#     area 0.0.0.100 range 2001:db3::/32 cost 120
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

- name: Replace device configurations of listed OSPFv3 processes with provided configurations
  cisco.nxos.nxos_ospfv3:
    config:
      processes:
        - process_id: 102
          router_id: 198.51.100.1
          address_family:
            afi: ipv6
            safi: unicast
            areas:
              - area_id: 0.0.0.100
                filter_list:
                  - route_map: rmap_8
                    direction: in
                ranges:
                  - not_advertise: true
                    prefix: 2001:db2::/32
            redistribute:
              - protocol: eigrp
                id: 130
                route_map: rmap_1
              - protocol: direct
                route_map: ospf102-direct-connect
          vrfs:
            - vrf: zone1
              router_id: 198.51.100.129
              areas:
                - area_id: 0.0.0.102
                  nssa:
                    default_information_originate: true
                    no_summary: true
    state: replaced

# Task output:
# ------------
# before:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv4
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: out
#            route_map: rmap_2
#          - direction: in
#            route_map: rmap_1
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#          - cost: 120
#            prefix: 2001:db3::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "120"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#
#  commands:
#  - router ospf 102
#  - address-family ipv6 unicast
#  - redistribute eigrp 130 route-map rmap_1
#  - no redistribute eigrp 120 route-map rmap_1
#  - area 0.0.0.100 filter-list route-map rmap_8 in
#  - no area 0.0.0.100 filter-list route-map rmap_2 out
#  - no area 0.0.0.100 range 2001:db3::/32
#  - vrf zone1
#  - no area 0.0.0.103 nssa
#  - no area 0.0.0.103 nssa translate type7 always
#  - no vrf zone2
#
# after:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv6
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: in
#            route_map: rmap_8
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "130"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        router_id: 198.51.100.129
#        vrf: zone1

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
#   router-id 203.0.113.20
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family ipv6 unicast
#     redistribute direct route-map ospf102-direct-connect
#     redistribute eigrp 130 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_8 in
#     area 0.0.0.100 range 198.51.100.64/27 not-advertise
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate

# Using overridden

# Before state:
# -------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
#   router-id 203.0.113.20
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family ipv6 unicast
#     redistribute direct route-map ospf102-direct-connect
#     redistribute eigrp 120 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_2 out
#     area 0.0.0.100 filter-list route-map rmap_1 in
#     area 0.0.0.100 range 2001:db2::/32 not-advertise
#     area 0.0.0.100 range 2001:db3::/32 cost 120
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

- name: Override all OSPFv3 configuration with provided configuration
  cisco.nxos.nxos_ospfv3:
    config:
      processes:
        - process_id: 104
          router_id: 203.0.113.20
        - process_id: 102
          router_id: 198.51.100.1
          shutdown: true
    state: overridden

# Task output:
# ------------
# before:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv4
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: out
#            route_map: rmap_2
#          - direction: in
#            route_map: rmap_1
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#          - cost: 120
#            prefix: 2001:db3::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "120"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#
# commands:
#  - no router ospfv3 100
#  - router ospfv3 104
#  - router-id 203.0.113.20
#  - router ospfv3 102
#  - shutdown
#  - address-family ipv6 unicast
#  - no redistribute direct route-map ospf102-direct-connect
#  - no redistribute eigrp 120 route-map rmap_1
#  - no area 0.0.0.100 filter-list route-map rmap_2 out
#  - no area 0.0.0.100 filter-list route-map rmap_1 in
#  - no area 0.0.0.100 range 2001:db2::/32
#  - no area 0.0.0.100 range 2001:db3::/32
#  - no vrf zone1
#  - no vrf zone2
#
# after:
#    processes:
#    - process_id: "102"
#      router_id: 198.51.100.1
#      shutdown: true
#      address_family:
#        afi: ipv6
#        safi: unicast
#    - process_id: "104"
#      router_id: 203.0.113.20

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family ipv6 unicast
#   shutdown
# router ospfv3 104
#   router-id 203.0.113.20

# Using deleted to delete a single OSPF process

# Before state:
# -------------
# nxos-9k-rdo# sh running-config | section "^router ospf .*"
# router ospfv3 100
#   router-id 203.0.113.20
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family ipv6 unicast
#     redistribute direct route-map ospf102-direct-connect
#     redistribute eigrp 120 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_2 out
#     area 0.0.0.100 filter-list route-map rmap_1 in
#     area 0.0.0.100 range 2001:db2::/32 not-advertise
#     area 0.0.0.100 range 2001:db3::/32 cost 120
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

- name: Delete a single OSPFv3 process
  cisco.nxos.nxos_ospfv3:
    config:
      processes:
        - process_id: 102
    state: deleted

# Task output:
# ------------
# before:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv4
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: out
#            route_map: rmap_2
#          - direction: in
#            route_map: rmap_1
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#          - cost: 120
#            prefix: 2001:db3::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "120"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#
# commands:
#   - no router ospfv3 102
#
# after:
#   processes:
#   - process_id: "100"
#     router_id: 203.0.113.20

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
#   router-id 203.0.113.20

# Using deleted all OSPFv3 processes from the device

# Before state:
# -------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# router ospfv3 100
#   router-id 203.0.113.20
# router ospfv3 102
#   router-id 198.51.100.1
#   address-family ipv6 unicast
#     redistribute direct route-map ospf102-direct-connect
#     redistribute eigrp 120 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_2 out
#     area 0.0.0.100 filter-list route-map rmap_1 in
#     area 0.0.0.100 range 2001:db2::/32 not-advertise
#     area 0.0.0.100 range 2001:db3::/32 cost 120
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.0.102 nssa no-summary default-information-originate
#     area 0.0.0.103 nssa no-summary
#     area 0.0.0.103 nssa translate type7 always
#   vrf zone2
#     auto-cost reference-bandwidth 45 Gbps

- name: Delete all OSPFv3 processes from the device
  cisco.nxos.nxos_ospfv3:
    state: deleted

# Task output:
# ------------
# before:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv4
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: out
#            route_map: rmap_2
#          - direction: in
#            route_map: rmap_1
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#          - cost: 120
#            prefix: 2001:db3::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "120"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#
# commands:
#  - no router ospfv3 100
#  - no router ospfv3 102
#
#  after: {}

# After state:
# ------------
# nxos-9k-rdo# sh running-config | section "^router ospfv3"
# nxos-9k-rdo#

# Using rendered

- name: Render platform specific configuration lines with state rendered (without connecting to the device)
  cisco.nxos.nxos_ospfv3:
    config:
      processes:
        - process_id: 100
          router_id: 203.0.113.20
        - process_id: 102
          router_id: 198.51.100.1
          address_family:
            afi: ipv6
            safi: unicast
            areas:
              - area_id: 0.0.0.100
                filter_list:
                  - route_map: rmap_1
                    direction: in
                  - route_map: rmap_2
                    direction: out
                ranges:
                  - prefix: 2001:db2::/32
                    not_advertise: true
                  - prefix: 2001:db3::/32
                    cost: 120
            redistribute:
              - protocol: eigrp
                id: 120
                route_map: rmap_1
              - protocol: direct
                route_map: ospf102-direct-connect
          vrfs:
            - vrf: zone1
              router_id: 198.51.100.129
              areas:
                - area_id: 0.0.0.102
                  nssa:
                    default_information_originate: true
                    no_summary: true
                - area_id: 0.0.0.103
                  nssa:
                    no_summary: true
                    translate:
                      type7:
                        always: true
            - vrf: zone2
              auto_cost:
                reference_bandwidth: 45
                unit: Gbps
    state: rendered

# Task output:
# ------------
# rendered:
#  - router ospfv3 100
#  - router-id 203.0.113.20
#  - router ospfv3 102
#  - router-id 198.51.100.1
#  - address-family ipv6 unicast
#  - redistribute eigrp 120 route-map rmap_1
#  - redistribute direct route-map ospf102-direct-connect
#  - area 0.0.0.100 filter-list route-map rmap_1 in
#  - area 0.0.0.100 filter-list route-map rmap_2 out
#  - area 0.0.0.100 range 2001:db2::/32 not-advertise
#  - area 0.0.0.100 range 2001:db3::/32 cost 120
#  - vrf zone1
#  - router-id 198.51.100.129
#  - area 0.0.0.102 nssa no-summary default-information-originate
#  - area 0.0.0.103 nssa no-summary
#  - area 0.0.0.103 nssa translate type7 always
#  - vrf zone2
#  - auto-cost reference-bandwidth 45 Gbps

# Using parsed

# parsed.cfg
# ------------
# router ospfv3 100
#   router-id 192.0.100.1
#   address-family ipv6 unicast
#     redistribute direct route-map ospf-direct-connect
#     redistribute eigrp 120 route-map rmap_1
#     area 0.0.0.100 filter-list route-map rmap_2 out
#     area 0.0.0.100 filter-list route-map rmap_1 in
#     area 0.0.0.100 range 2001:db2::/32 not-advertise
#     area 0.0.0.100 range 2001:db3::/32 cost 120
#   vrf zone1
#     router-id 198.51.100.129
#     area 0.0.100.1 nssa no-summary no-redistribution
# router ospfv3 102
#   router-id 198.54.100.1
#   shutdown

- name: Parse externally provided OSPFv3 config
  cisco.nxos.nxos_ospfv3:
    running_config: "{{ lookup('file', 'ospfv2.cfg') }}"
    state: parsed

# Task output:
# ------------
# parsed:
#   processes:
#   - process_id: "100"
#     address_family:
#       afi: ipv6
#       safi: unicast
#       areas:
#       - area_id: 0.0.0.101
#         nssa:
#           no_redistribution: true
#           no_summary: true
#       - area_id: 0.0.0.102
#         stub:
#           no_summary: true
#         filter_list:
#           - direction: out
#             route_map: rmap_2
#           - direction: in
#             route_map: rmap_1
#         ranges:
#           - not_advertise: true
#             prefix: 192.0.2.0/24
#           - cost: 120
#             prefix: 192.0.3.0/24
#       redistribute:
#       - protocol: direct
#         route_map: ospf-direct-connect
#       - id: "120"
#         protocol: eigrp
#         route_map: rmap_1
#     router_id: 192.0.100.1
#     vrfs:
#       - vrf: zone1
#         areas:
#           - area_id: 0.0.100.1
#             nssa:
#               no_redistribution: true
#               no_summary: true
#         router_id: 192.0.100.2
#   - process_id: "102"
#     router_id: 198.54.100.1
#     shutdown: true

# Using gathered

- name: Gather OSPFv3 facts using gathered
  cisco.nxos.nxos_ospfv3:
    state: gathered

# Task output:
# ------------
#  gathered:
#    processes:
#    - process_id: "100"
#      router_id: 203.0.113.20
#    - address_family:
#        afi: ipv4
#        safi: unicast
#        areas:
#        - area_id: 0.0.0.100
#          filter_list:
#          - direction: out
#            route_map: rmap_2
#          - direction: in
#            route_map: rmap_1
#          ranges:
#          - not_advertise: true
#            prefix: 2001:db2::/32
#          - cost: 120
#            prefix: 2001:db3::/32
#        redistribute:
#        - protocol: direct
#          route_map: ospf102-direct-connect
#        - id: "120"
#          protocol: eigrp
#          route_map: rmap_1
#      process_id: "102"
#      router_id: 198.51.100.1
#      vrfs:
#      - areas:
#        - area_id: 0.0.0.102
#          nssa:
#            default_information_originate: true
#            no_summary: true
#        - area_id: 0.0.0.103
#          nssa:
#            no_summary: true
#            translate:
#              type7:
#                always: true
#        router_id: 198.51.100.129
#        vrf: zone1
#      - auto_cost:
#          reference_bandwidth: 45
#          unit: Gbps
#        vrf: zone2
#

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Description
after dictionary	The resulting configuration model invocation. Returned: when changed Sample: "The configuration returned will always be in the same format\n of the parameters above.\n"
before dictionary	The configuration prior to the model invocation. Returned: always Sample: "The configuration returned will always be in the same format\n of the parameters above.\n"
commands list / elements=string	The set of commands pushed to the remote device. Returned: always Sample: ["router ospfv3 102", "router-id 198.54.100.1", "router ospfv3 100", "router-id 192.0.100.1", "address-family ipv6 unicast", "redistribute eigrp 120 route-map rmap_1", "redistribute direct route-map ospf-direct-connect", "area 0.0.0.100 filter-list route-map rmap_1 in", "area 0.0.0.100 filter-list route-map rmap_2 out", "area 0.0.0.100 range 2001:db2::/32 not-advertise", "area 0.0.0.100 range 2001:db3::/32 cost 120", "vrf zone1", "router-id 192.0.100.2", "vrf zone2", "auto-cost reference-bandwidth 45 Gbps"]
gathered dictionary	Facts about the network resource gathered from the remote device as structured data. Returned: when state is gathered Sample: "This output will always be in the same format as the module argspec.\n"
parsed dictionary	The device native config provided in running_config option parsed into structured data as per module argspec. Returned: when state is parsed Sample: "This output will always be in the same format as the module argspec.\n"
rendered list / elements=string	The provided configuration in the task rendered in device-native format (offline). Returned: when state is rendered Sample: ["router ospfv3 102", "router-id 198.54.100.1", "router ospfv3 100"]

Authors

• Nilashish Chakraborty (@NilashishC)

Collection links

• Issue Tracker
• Repository (Sources)