community.network.icx_l3_interface module – Manage Layer-3 interfaces on Ruckus ICX 7000 series switches

Note

This module is part of the community.network collection (version 4.0.1).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install community.network.

To use it in a playbook, specify: community.network.icx_l3_interface.

Synopsis

  • This module provides declarative management of Layer-3 interfaces on ICX network devices.

Parameters

Parameter

Comments

aggregate

list / elements=dictionary

List of Layer-3 interfaces definitions. Each of the entry in aggregate list should define name of interface name and a optional ipv4 or ipv6 address.

check_running_config

boolean

Check running configuration. This can be set as environment variable. Module will use environment variable value(default:True), unless it is overridden, by specifying it as module parameter.

Choices:

  • no

  • yes

ipv4

string

IPv4 address to be set for the Layer-3 interface mentioned in name option. The address format is <ipv4 address>/<mask>, the mask is number in range 0-32 eg. 192.168.0.1/24

ipv6

string

IPv6 address to be set for the Layer-3 interface mentioned in name option. The address format is <ipv6 address>/<mask>, the mask is number in range 0-128 eg. fd5d:12c9:2201:1::1/64.

mode

string

Specifies if ipv4 address should be dynamic/advertise to ospf/not advertise to ospf. This should be specified only if ipv4 address is configured and if it is not secondary IP address.

Choices:

  • dynamic

  • ospf-ignore

  • ospf-passive

name

string

Name of the Layer-3 interface to be configured eg. GigabitEthernet0/2, ve 10, ethernet 1/1/1

replace

string

Replaces the configured primary IP address on the interface.

Choices:

  • yes

  • no

secondary

string

Specifies that the configured address is a secondary IP address. If this keyword is omitted, the configured address is the primary IP address.

Choices:

  • yes

  • no

state

string

State of the Layer-3 interface configuration. It indicates if the configuration should be present or absent on remote device.

Choices:

  • present

  • absent

check_running_config

boolean

Check running configuration. This can be set as environment variable. Module will use environment variable value(default:True), unless it is overridden, by specifying it as module parameter.

Choices:

  • no

  • yes ← (default)

ipv4

string

IPv4 address to be set for the Layer-3 interface mentioned in name option. The address format is <ipv4 address>/<mask>, the mask is number in range 0-32 eg. 192.168.0.1/24

ipv6

string

IPv6 address to be set for the Layer-3 interface mentioned in name option. The address format is <ipv6 address>/<mask>, the mask is number in range 0-128 eg. fd5d:12c9:2201:1::1/64.

mode

string

Specifies if ipv4 address should be dynamic/advertise to ospf/not advertise to ospf. This should be specified only if ipv4 address is configured and if it is not secondary IP address.

Choices:

  • dynamic

  • ospf-ignore

  • ospf-passive

name

string

Name of the Layer-3 interface to be configured eg. GigabitEthernet0/2, ve 10, ethernet 1/1/1

replace

string

Replaces the configured primary IP address on the interface.

Choices:

  • yes

  • no

secondary

string

Specifies that the configured address is a secondary IP address. If this keyword is omitted, the configured address is the primary IP address.

Choices:

  • yes

  • no

state

string

State of the Layer-3 interface configuration. It indicates if the configuration should be present or absent on remote device.

Choices:

  • present ← (default)

  • absent

Notes

Note

Examples

- name: Remove ethernet 1/1/1 IPv4 and IPv6 address
  community.network.icx_l3_interface:
    name: ethernet 1/1/1
    ipv4: 192.168.0.1/24
    ipv6: "fd5d:12c9:2201:1::1/64"
    state: absent

- name: Replace ethernet 1/1/1 primary IPv4 address
  community.network.icx_l3_interface:
    name: ethernet 1/1/1
    ipv4: 192.168.0.1/24
    replace: yes
    state: absent

- name: Replace ethernet 1/1/1 dynamic IPv4 address
  community.network.icx_l3_interface:
    name: ethernet 1/1/1
    ipv4: 192.168.0.1/24
    mode: dynamic
    state: absent

- name: Set ethernet 1/1/1 secondary IPv4 address
  community.network.icx_l3_interface:
    name: ethernet 1/1/1
    ipv4: 192.168.0.1/24
    secondary: yes
    state: absent

- name: Set ethernet 1/1/1 IPv4 address
  community.network.icx_l3_interface:
    name: ethernet 1/1/1
    ipv4: 192.168.0.1/24

- name: Set ethernet 1/1/1 IPv6 address
  community.network.icx_l3_interface:
    name: ethernet 1/1/1
    ipv6: "fd5d:12c9:2201:1::1/64"

- name: Set IP addresses on aggregate
  community.network.icx_l3_interface:
    aggregate:
      - { name: GigabitEthernet0/3, ipv4: 192.168.2.10/24 }
      - { name: GigabitEthernet0/3, ipv4: 192.168.3.10/24, ipv6: "fd5d:12c9:2201:1::1/64" }

- name: Remove IP addresses on aggregate
  community.network.icx_l3_interface:
    aggregate:
      - { name: GigabitEthernet0/3, ipv4: 192.168.2.10/24 }
      - { name: GigabitEthernet0/3, ipv4: 192.168.3.10/24, ipv6: "fd5d:12c9:2201:1::1/64" }
    state: absent


- name: Set the ipv4 and ipv6 of a virtual ethernet(ve)
  community.network.icx_l3_interface:
    name: ve 100
    ipv4: 192.168.0.1
    ipv6: "2001:0db8:85a3:0000:0000:8a2e:0370:7334"

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key

Description

commands

list / elements=string

The list of configuration mode commands to send to the device

Returned: always, except for the platforms that use Netconf transport to manage the device.

Sample: [“interface ethernet 1/1/1”, “ip address 192.168.0.1 255.255.255.0”, “ipv6 address fd5d:12c9:2201:1::1/64”]

Authors

  • Ruckus Wireless (@Commscope)