f5networks.f5_modules.bigip_network_globals module – Manage network global settings on BIG-IP

Note

This module is part of the f5networks.f5_modules collection (version 1.33.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install f5networks.f5_modules.

To use it in a playbook, specify: f5networks.f5_modules.bigip_network_globals.

New in f5networks.f5_modules 1.0.0

Synopsis 

Module to manage STP, Multicast, DAG, LLDP and Self Allow global settings on a BIG-IP.

Parameters 

Parameter	Comments
dag dictionary	Manage global disaggregation settings.
dag_ipv6_prefix_len integer	Specifies whether SPDAG or IPv6 prefix DAG should be used to disaggregate IPv6 traffic when vlan cmp hash is set to `src-ip` or `dst-ip`. The valid value range is 0 - 128, with `128` value SPAG is in use. This option is only available in TMOS version `13.x` and above.
icmp_hash string	Specifies the ICMP hash for ICMP echo request and ICMP echo reply in SW DAG. When `icmp`, ICMP echo request and ICMP echo reply are disaggregated based on ICMP id. When `ipicmp`, ICMP echo request and ICMP echo reply are disaggregated based on ICMP id and IP addresses. This option is only available in `TMOS` version `13.x` and above. Choices: `"icmp"` `"ipicmp"`
round_robin_mode string	Specifies whether the round robin disaggregator (DAG) on a blade can disaggregate packets to all the TMMs in the system or only to the TMMs local to the blade. When `global`, the DAG will disaggregate packets to all TMMs in the system. When `local`, the DAG will disaggregate packets only to the TMMs local to the blade. Choices: `"global"` `"local"`
lldp dictionary	Manage LLDP configuration options.
enabled boolean	Specifies the current status of LLDP. When `true`, the LLDP is enabled globally on the device. When `false`, the LLDP is disabled globally on the device. Choices: `false` `true`
max_neighbors_per_port integer	Specifies the maximum number of neighbors per port. The valid value range is 0 - 65535.
reinit_delay integer	Specifies the maximum number of seconds to wait after reaching the TTL interval before resetting TTL timer. The valid value range is 0 - 65535.
tx_delay integer	Specifies the number of seconds to wait for LLDP to initialize on an interface before sending LLDP message. The valid value range is 0 - 65535.
tx_hold integer	Specifies the multiplier that determines the LLDP Time to Live (TTL). TTL is determined by multiplying this value and `tx_interval`. The valid value range is 0 - 65535.
tx_interval integer	Specifies the interval devices use to send LLDP information from each of their interfaces. The valid value range is 0 - 65535.
multicast dictionary	Manage multicast traffic configuration options.
max_pending_packets integer	Specifies the maximum number of packet queued on behalf of a single incomplete MFC entry. The valid range is 0 - 4294967295.
max_pending_routes integer	Specifies the number of incomplete MFC entries each TMM will allow to exist at one time. The valid range is 0 - 4294967295.
rate_limit boolean	When `true`, the DB variable `switchboard.maxmcastrate` setting controls the multicast packet per second rate limiting in the switch. Choices: `false` `true`
route_lookup_timeout integer	Specifies maximum lifetime of an incomplete MFC entry, in seconds. The valid range is 0 - 4294967295.
provider dictionary added in f5networks.f5_modules 1.0.0	A dict object containing connection details.
auth_provider string	Configures the auth provider for to obtain authentication tokens from the remote device. This option is really used when working with BIG-IQ devices.
no_f5_teem boolean	If `yes`, TEEM telemetry data is not sent to F5. You may omit this option by setting the environment variable `F5_TELEMETRY_OFF`. Previously used variable `F5_TEEM` is deprecated as its name was confusing. Choices: `false` ← (default) `true`
password aliases: pass, pwd string / required	The password for the user account used to connect to the BIG-IP or the BIG-IQ. You may omit this option by setting the environment variable `F5_PASSWORD`.
server string / required	The BIG-IP host or the BIG-IQ host. You may omit this option by setting the environment variable `F5_SERVER`.
server_port integer	The BIG-IP server port. You may omit this option by setting the environment variable `F5_SERVER_PORT`. Default: `443`
timeout integer	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
transport string	Configures the transport connection to use when connecting to the remote device. Choices: `"rest"` ← (default)
user string / required	The username to connect to the BIG-IP or the BIG-IQ. This user must have administrative privileges on the device. You may omit this option by setting the environment variable `F5_USER`.
validate_certs boolean	If `no`, SSL certificates are not validated. Use this only on personally controlled sites using self-signed certificates. You may omit this option by setting the environment variable `F5_VALIDATE_CERTS`. Choices: `false` `true` ← (default)
self_allow dictionary added in f5networks.f5_modules 1.1.0	Manage Self Allow global configuration options.
all boolean	Sets all or none ports and protocols as a system wide `self_allow` setting. When `true`, the self_allow allows all protocols and ports. This is the equivalent of setting all option in `TMSH`. When `false`, the self_allow allows no protocols and ports. This is the equivalent of setting none option in `TMSH`. Choices: `false` `true`
defaults list / elements=dictionary	The default set of protocols and ports allowed by a self IP if the self IP allow-service setting is default.
port integer	The port number to be set. The valid value range is 0 - 65535.
protocol string	The protocol name to be set.
stp dictionary	Manage global settings for STP on BIG-IP.
config_name string	Specifies the configuration name. The accepted length is from 1 to 32 characters. Only has effect when the `mode` is `mstp`.
config_revision integer	Specifies the revision level of the MSTP configuration, when `mode` is `mstp`. You must specify a number in the range of 0 to 65535.
description string	User-defined description.
fwd_delay integer	The number of seconds for which an interface was blocked from forwarding network traffic after a reconfiguration of the spanning tree topology. This parameter has no effect when `rstp` or `mstp` modes are used, as long as all bridges in the spanning tree use the RSTP or MSTP protocol. If any legacy STP bridges are present, neighboring bridges must fall back to the old protocol, whose reconfiguration time is affected by the forward delay value. The valid range is 4 to 30.
hello_time integer	Specifies the time interval in seconds between the periodic transmissions that communicate spanning tree information to the adjacent bridges in the network. The hello time set by default on the device is optimal in virtually all cases. F5 recommends that you do not change the hello time. The valid range is 1 to 10.
max_age integer	Specifies the number of seconds for which spanning tree information received from other bridges is considered valid. The valid range is 6 to 40 seconds.
max_hops integer	Specifies the maximum number of hops an MSTP packet may travel before it is discarded. This option only takes effect when `mode` is `mstp`. The number of hops must be in the range of 1 to 255.
mode string	Specifies the spanning tree mode. The `mstp`, `rstp` and `stp` options are only supported on hardware platforms. Attempting to set these modes on VE type platforms will result in failure. The only valid options on VE type platforms are: `passthru` and `disabled`. Choices: `"disabled"` `"mstp"` `"passthru"` `"rstp"` `"stp"`
transmit_hold integer	Specifies the absolute limit on the number of spanning tree protocol packets the traffic management system may transmit on a port in any hello time interval. The valid range is 1 to 10 packets.

Notes 

Note

For more information on using Ansible to manage F5 Networks devices see https://www.ansible.com/integrations/networks/f5.
Requires BIG-IP software version >= 12.
The F5 modules only manipulate the running configuration of the F5 product. To ensure that BIG-IP specific configuration persists to disk, be sure to include at least one task that uses the f5networks.f5_modules.bigip_config module to save the running configuration. Refer to the module’s documentation for the correct usage of the module to save your running configuration.

Examples 

- name: Update STP settings
  bigip_network_globals:
    stp:
      config_name: foobar
      config_revision: 1
      max_hops: 20
      mode: mstp
    provider:
      password: secret
      server: lb.mydomain.com
      user: admin
  delegate_to: localhost

- name: Update DAG settings
  bigip_network_globals:
    dag:
      icmp_hash: ipicmp
      round_robin_mode: local
    provider:
      password: secret
      server: lb.mydomain.com
      user: admin
  delegate_to: localhost

- name: Update multiple settings
  bigip_network_globals:
    stp:
      config_name: foobar
      config_revision: 1
      max_hops: 20
      mode: mstp
    dag:
      icmp_hash: ipicmp
      round_robin_mode: local
    provider:
      password: secret
      server: lb.mydomain.com
      user: admin
  delegate_to: localhost

Return Values 

Common return values are documented here, the following are the fields unique to this module:

Key	Description
dag complex	Manage multicast traffic configuration options. Returned: changed Sample: `"hash/dictionary of values"`
dag_ipv6_prefix_len integer	Specifies whether SPDAG or IPv6 prefix DAG should be used to disaggregate IPv6 traffic. Returned: changed Sample: `128`
icmp_hash string	Specifies the ICMP hash for the ICMP echo request and ICMP echo reply in SW DAG. Returned: changed Sample: `"ipicmp"`
round_robin_mode string	The mode of operation of the DAG on a blade. Returned: changed Sample: `"local"`
lldp complex	Manage multicast traffic configuration options. Returned: changed Sample: `"hash/dictionary of values"`
enabled boolean	The current status of LLDP. Returned: changed Sample: `true`
max_neighbors_per_port integer	The maximum number of neighbors per port. Returned: changed Sample: `128`
reinit_delay integer	The maximum number of seconds to wait before resetting the TTL timer after reaching the TTL interval. Returned: changed Sample: `30`
tx_delay integer	The number of seconds to wait for LLDP to initialize on an interface before sending LLDP message. Returned: changed Sample: `500`
tx_hold integer	The multiplier that determines the LLDP Time to Live. Returned: changed Sample: `10`
tx_interval integer	The interval devices use to send LLDP information from each of their interfaces. Returned: changed Sample: `240`
multicast complex	Manage multicast traffic configuration options. Returned: changed Sample: `"hash/dictionary of values"`
max_pending_packets integer	The maximum number of packet queued on behalf of a single incomplete MFC entry. Returned: changed Sample: `3000`
max_pending_routes integer	The number of incomplete MFC entries each TMM will allow to exist at one time. Returned: changed Sample: `50`
rate_limit boolean	Enables DB variable control over multicast packet per second rate limiting in the switch. Returned: changed Sample: `true`
route_lookup_timeout integer	The maximum lifetime of an incomplete MFC entry, in seconds. Returned: changed Sample: `20`
self_allow complex	Manages self_allow system wide settings. Returned: changed Sample: `"hash/dictionary of values"`
all boolean	Allows all or none ports and protocols as a system wide self_allow setting. Returned: changed Sample: `true`
defaults complex	The default set of protocols and ports allowed by a self IP. Returned: changed Sample: `"hash/dictionary of values"`
port integer	The port number to be set. Returned: changed Sample: `443`
protocol string	The protocol name to be set. Returned: changed Sample: `"tcp"`
stp complex	Manage global settings for STP on BIG-IP. Returned: changed Sample: `"hash/dictionary of values"`
config_name string	The configuration name. Returned: changed Sample: `"foobar"`
config_revision integer	The revision level of the MSTP configuration. Returned: changed Sample: `2`
description string	User-defined description. Returned: changed Sample: `"My description"`
fwd_delay integer	The number of seconds for which an interface was blocked from forwarding network traffic. Returned: changed Sample: `4`
hello_time integer	The time interval at seconds between the periodic transmissions of spanning tree information. Returned: changed Sample: `2`
max_age integer	The number of seconds that spanning tree information received from other bridges is considered valid. Returned: changed Sample: `30`
max_hops integer	The maximum number of hops an MSTP packet may travel before it is discarded. Returned: changed Sample: `15`
mode string	The spanning tree mode. Returned: changed Sample: `"mstp"`
transmit_hold integer	The limit on the number of STP the traffic management system may transmit on a port in any hello time interval. Returned: changed Sample: `5`

Authors

Wojciech Wypior (@wojtek0806)

f5networks.f5_modules.bigip_network_globals module – Manage network global settings on BIG-IP

Synopsis

Parameters

Notes

Examples

Return Values