cisco.nxos.nxos_vpc module – Manages global VPC configuration
Note
This module is part of the cisco.nxos collection (version 8.1.0).
You might already have this collection installed if you are using the ansible
package.
It is not included in ansible-core
.
To check whether it is installed, run ansible-galaxy collection list
.
To install it, use: ansible-galaxy collection install cisco.nxos
.
To use it in a playbook, specify: cisco.nxos.nxos_vpc
.
New in cisco.nxos 1.0.0
Synopsis
Manages global VPC configuration
Aliases: vpc
Parameters
Parameter |
Comments |
---|---|
Enables/Disables auto recovery on platforms that support disable timers are not modifiable with this attribute mutually exclusive with auto_recovery_reload_delay Choices:
|
|
Manages auto-recovery reload-delay timer in seconds mutually exclusive with auto_recovery |
|
manages delay restore command and config value in seconds |
|
manages delay restore interface-vlan command and config value in seconds not supported on all platforms |
|
manages delay restore orphan-port command and config value in seconds not supported on all platforms |
|
VPC domain |
|
Enables/Disables peer gateway Choices:
|
|
Destination (remote) IP address used for peer keepalive link pkl_dest is required whenever pkl options are used. |
|
Source IP address used for peer keepalive link |
|
VRF used for peer keepalive link The VRF must exist on the device before using pkl_vrf. (Note) ‘default’ is an overloaded term: Default vrf context for pkl_vrf is ‘management’; ‘pkl_vrf: default’ refers to the literal ‘default’ rib. |
|
Role priority for device. Remember lower is better. |
|
Manages desired state of the resource Choices:
|
|
System priority device. Remember they must match between peers. |
Notes
Note
Tested against NXOSv 7.3.(0)D1(1) on VIRL
Unsupported for Cisco MDS
The feature vpc must be enabled before this module can be used
If not using management vrf, vrf must be globally on the device before using in the pkl config
Although source IP isn’t required on the command line it is required when using this module. The PKL VRF must also be configured prior to using this module.
Both pkl_src and pkl_dest are needed when changing PKL VRF.
For information on using CLI and NX-API see the :ref:`NXOS Platform Options guide <nxos_platform_options>`
For more information on using Ansible to manage network devices see the :ref:`Ansible Network Guide <network_guide>`
For more information on using Ansible to manage Cisco devices see the `Cisco integration page <https://www.ansible.com/integrations/networks/cisco>`_.
Examples
- name: configure a simple asn
cisco.nxos.nxos_vpc:
domain: 100
role_priority: 1000
system_priority: 2000
pkl_dest: 192.168.100.4
pkl_src: 10.1.100.20
peer_gw: true
auto_recovery: true
- name: configure
cisco.nxos.nxos_vpc:
domain: 100
role_priority: 32667
system_priority: 2000
peer_gw: true
pkl_src: 10.1.100.2
pkl_dest: 192.168.100.4
auto_recovery: true
- name: Configure VPC with delay restore and existing keepalive VRF
cisco.nxos.nxos_vpc:
domain: 10
role_priority: 28672
system_priority: 2000
delay_restore: 180
peer_gw: true
pkl_src: 1.1.1.2
pkl_dest: 1.1.1.1
pkl_vrf: vpckeepalive
auto_recovery: true
Return Values
Common return values are documented here, the following are the fields unique to this module:
Key |
Description |
---|---|
commands sent to the device Returned: always Sample: |