You are reading an unmaintained version of the Ansible documentation. Unmaintained Ansible versions can contain unfixed security vulnerabilities (CVE). Please upgrade to a maintained version. See the latest Ansible documentation.

junipernetworks.junos.junos_interface – (deprecated, removed after 2022-06-01) Manage Interface on Juniper JUNOS network devices

Note

This plugin is part of the junipernetworks.junos collection (version 2.8.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install junipernetworks.junos.

To use it in a playbook, specify: junipernetworks.junos.junos_interface.

New in version 1.0.0: of junipernetworks.junos

DEPRECATED
Synopsis
Requirements
Parameters
Notes
Examples
Return Values
Status

DEPRECATED 

Removed in: major release after 2022-06-01
Why: Updated modules released with more functionality
Alternative: Use junipernetworks.junos.junos_interfaces instead.

Synopsis 

This module provides declarative management of Interfaces on Juniper JUNOS network devices.

Note

This module has a corresponding action plugin.

Requirements 

The below requirements are needed on the host that executes this module.

ncclient (>=v0.5.2)

Parameters 

Parameter	Comments
active boolean	Specifies whether or not the configuration is active or deactivated Choices: no yes ← (default)
aggregate list / elements=dictionary	List of Interfaces definitions.
active boolean	Specifies whether or not the configuration is active or deactivated Choices: no yes
delay integer	Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values `up`/`down`, tx_rate and rx_rate.
description string	Description of Interface.
duplex string	Interface link status. Choices: full half auto
enabled boolean	Configure interface link status. Choices: no yes
mtu integer	Maximum size of transmit packet.
name string / required	Name of the Interface.
neighbors list / elements=dictionary	Check the operational state of given interface `name` for LLDP neighbor. The following suboptions are available.
host string	LLDP neighbor host for given interface `name`.
port string	LLDP neighbor port to which given interface `name` is connected.
rx_rate string	Receiver rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
speed string	Interface link speed.
state string	State of the Interface configuration, `up` indicates present and operationally up and `down` indicates present and operationally `down` Choices: present absent up down
tx_rate string	Transmit rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
delay integer	Time in seconds to wait before checking for the operational state on remote device. This wait is applicable for operational state argument which are state with values `up`/`down`, tx_rate and rx_rate. Default: 10
description string	Description of Interface.
duplex string	Interface link status. Choices: full half auto
enabled boolean	Configure interface link status. Choices: no yes ← (default)
mtu integer	Maximum size of transmit packet.
name string	Name of the Interface.
neighbors list / elements=dictionary	Check the operational state of given interface `name` for LLDP neighbor. The following suboptions are available.
host string	LLDP neighbor host for given interface `name`.
port string	LLDP neighbor port to which given interface `name` is connected.
provider dictionary	Deprecated Starting with Ansible 2.5 we recommend using `connection: network_cli` or `connection: netconf`. For more information please see the Junos OS Platform Options guide. A dict object containing connection details.
host string	Specifies the DNS host name or address for connecting to the remote device over the specified transport. The value of host is used as the destination address for the transport.
password string	Specifies the password to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_PASSWORD` will be used instead.
port integer	Specifies the port to use when building the connection to the remote device. The port value will default to the well known SSH port of 22 (for `transport=cli`) or port 830 (for `transport=netconf`) device.
ssh_keyfile path	Specifies the SSH key to use to authenticate the connection to the remote device. This value is the path to the key used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_SSH_KEYFILE` will be used instead.
timeout integer	Specifies the timeout in seconds for communicating with the network device for either connecting or sending commands. If the timeout is exceeded before the operation is completed, the module will error.
transport string	Configures the transport connection to use when connecting to the remote device. Choices: cli netconf ← (default)
username string	Configures the username to use to authenticate the connection to the remote device. This value is used to authenticate the SSH session. If the value is not specified in the task, the value of environment variable `ANSIBLE_NET_USERNAME` will be used instead.
rx_rate string	Receiver rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules
speed string	Interface link speed.
state string	State of the Interface configuration, `up` indicates present and operationally up and `down` indicates present and operationally `down` Choices: present ← (default) absent up down
tx_rate string	Transmit rate in bits per second (bps). This is state check parameter only. Supports conditionals, see Conditionals in Networking Modules

Notes 

Note

This module requires the netconf system service be enabled on the remote device being managed.
Tested against vSRX JUNOS version 15.1X49-D15.4, vqfx-10000 JUNOS Version 15.1X53-D60.4.
Recommended connection is netconf. See the Junos OS Platform Options.
This module also works with local connections for legacy playbooks.
For information on using CLI and netconf see the Junos OS Platform Options guide
For more information on using Ansible to manage network devices see the Ansible Network Guide
For more information on using Ansible to manage Juniper network devices see https://www.ansible.com/ansible-juniper.

Examples 

- name: configure interface
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    description: test-interface

- name: remove interface
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    state: absent

- name: make interface down
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    enabled: false

- name: make interface up
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    enabled: true

- name: Deactivate interface config
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    state: present
    active: false

- name: Activate interface config
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    state: present
    active: true

- name: Configure interface speed, mtu, duplex
  junipernetworks.junos.junos_interface:
    name: ge-0/0/1
    state: present
    speed: 1g
    mtu: 256
    duplex: full

- name: Create interface using aggregate
  junipernetworks.junos.junos_interface:
    aggregate:
    - name: ge-0/0/1
      description: test-interface-1
    - name: ge-0/0/2
      description: test-interface-2
    speed: 1g
    duplex: full
    mtu: 512

- name: Delete interface using aggregate
  junipernetworks.junos.junos_interface:
    aggregate:
    - name: ge-0/0/1
    - name: ge-0/0/2
    state: absent

- name: Check intent arguments
  junipernetworks.junos.junos_interface:
    name: '{{ name }}'
    state: up
    tx_rate: ge(0)
    rx_rate: le(0)

- name: Check neighbor intent
  junipernetworks.junos.junos_interface:
    name: xe-0/1/1
    neighbors:
    - port: Ethernet1/0/1
      host: netdev

- name: Config + intent
  junipernetworks.junos.junos_interface:
    name: '{{ name }}'
    enabled: false
    state: down

Return Values 

Common return values are documented here, the following are the fields unique to this module:

Key	Description
diff.prepared string	Configuration difference before and after applying change. Returned: when configuration is changed and diff option is enabled. Sample: “[edit interfaces] + ge-0/0/1 { + description test-interface; + }\n”

Status 

This module will be removed in a major release after 2022-06-01. [deprecated]
For more information see DEPRECATED.

Authors

Ganesh Nalawade (@ganeshrn)