cisco.iosxr.iosxr_l2_interfaces module – L2 interfaces resource module

Note

This module is part of the cisco.iosxr collection (version 2.9.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install cisco.iosxr.

To use it in a playbook, specify: cisco.iosxr.iosxr_l2_interfaces.

New in version 1.0.0: of cisco.iosxr

Synopsis

  • This module manages the Layer-2 interface attributes on Cisco IOS-XR devices.

Parameters

Parameter

Comments

config

list / elements=dictionary

A dictionary of Layer-2 interface options

encapsulation

dictionary

Specify which packets will be matched by this sub-interface.

dot1q

integer

IEEE 802.1Q VLAN-tagged packets.

second_dot1q

integer

IEEE 802.1Q VLAN-tagged packets.

l2protocol

list / elements=dictionary

Configures Layer 2 protocol tunneling and protocol data unit (PDU) filtering on an interface.

cdp

string

Cisco Discovery Protocol (CDP) tunneling and data unit parameters.

Choices:

  • drop

  • forward

  • tunnel

cpsv

string

CDP, PVST+, STP, and VTP protocols.

Choices:

  • drop

  • reverse-tunnel

  • tunnel

pvst

string

Configures the per-VLAN Spanning Tree Protocol (PVST) tunneling and data unit parameters.

Choices:

  • drop

  • forward

  • tunnel

stp

string

Spanning Tree Protocol (STP) tunneling and data unit parameters.

Choices:

  • drop

  • forward

  • tunnel

vtp

string

VLAN Trunk Protocol (VTP) tunneling and data unit parameters.

Choices:

  • drop

  • forward

  • tunnel

l2transport

boolean

Switchport mode access command to configure the interface as a layer 2 access

Choices:

  • no

  • yes

name

string / required

Full name of the interface/sub-interface excluding any logical unit number, e.g. GigabitEthernet0/0/0/1 or GigabitEthernet0/0/0/1.100.

native_vlan

integer

Configure a native VLAN ID for the trunk

propagate

boolean

Propagate Layer 2 transport events. Note that it will work only when the l2tranport option is set to TRUE

Choices:

  • no

  • yes

q_vlan

list / elements=integer

802.1Q VLAN configuration. Note that it can accept either 2 VLAN IDs when configuring Q-in-Q VLAN, or it will accept 1 VLAN ID and ‘any’ as input list when configuring Q-in-any vlan as input. Note, that this option is valid only with respect to Sub-Interface and is not valid when configuring for Interface.

running_config

string

This option is used only with state parsed.

The value of this option should be the output received from the IOS-XR device by executing the command show running-config interface.

The state parsed reads the configuration from running_config option and transforms it into Ansible structured data as per the resource module’s argspec and the value is then returned in the parsed key within the result.

state

string

The state of the configuration after module completion

Choices:

  • merged ← (default)

  • replaced

  • overridden

  • deleted

  • rendered

  • gathered

  • parsed

Notes

Note

Examples

# Using merged
#
# Before state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
#  description Ansible Network
#  vrf custB
#  ipv4 address 10.10.0.2 255.255.255.0
#  duplex half
#  shutdown
# !
# interface GigabitEthernet0/0/0/4
#  description Test description
# !

- name: Merge provided configuration with device configuration
  cisco.iosxr.iosxr_l2_interfaces:
    config:
    - name: GigabitEthernet0/0/0/3
      native_vlan: 20
    - name: GigabitEthernet0/0/0/4
      native_vlan: 40
      l2transport: true
      l2protocol:
      - stp: tunnel
    - name: GigabitEthernet0/0/0/3.900
      l2transport: true
      q_vlan:
      - 20
      - 40
    state: merged

# After state:
# ------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
#  description Ansible Network
#  vrf custB
#  ipv4 address 10.10.0.2 255.255.255.0
#  duplex half
#  shutdown
#  dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
# description Test description
#  dot1q native vlan 10
#  l2transport
#   l2protocol stp tunnel
#  !
# !
# interface GigabitEthernet0/0/0/3.900 l2transport
#  dot1q vlan 20 40
# !

# Using replaced
#
# Before state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
#  description Ansible Network
#  vrf custB
#  ipv4 address 10.10.0.2 255.255.255.0
#  duplex half
#  shutdown
#  dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
# description Test description
#  dot1q native vlan 10
#  l2transport
#   l2protocol stp tunnel
#  !
# !
# interface GigabitEthernet0/0/0/3.900 l2transport
#  dot1q vlan 20 40
# !

- name: Replaces device configuration of listed interfaces with provided configuration
  cisco.iosxr.iosxr_l2_interfaces:
    config:
    - name: GigabitEthernet0/0/0/4
      native_vlan: 40
      l2transport: true
      l2protocol:
      - stp: forward
    - name: GigabitEthernet0/0/0/3.900
      q_vlan:
      - 20
      - any
    state: replaced

# After state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
#  description Ansible Network
#  vrf custB
#  ipv4 address 10.10.0.2 255.255.255.0
#  duplex half
#  shutdown
#  dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
# description Test description
#  dot1q native vlan 40
#  l2transport
#   l2protocol stp forward
#  !
# !
# interface GigabitEthernet0/0/0/3.900 l2transport
#  dot1q vlan 20 any
# !

# Using overridden
#
# Before state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
#  description Ansible Network
#  vrf custB
#  ipv4 address 10.10.0.2 255.255.255.0
#  duplex half
#  shutdown
#  dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
# description Test description
#  dot1q native vlan 10
#  l2transport
#   l2protocol stp tunnel
#  !
# !
# interface GigabitEthernet0/0/0/3.900 l2transport
#  dot1q vlan 20 40
# !

- name: Override device configuration of all interfaces with provided configuration
  cisco.iosxr.iosxr_l2_interfaces:
    config:
    - name: GigabitEthernet0/0/0/4
      native_vlan: 40
      l2transport: true
      l2protocol:
      - stp: forward
    - name: GigabitEthernet0/0/0/3.900
      q_vlan:
      - 20
      - any
    state: overridden

# After state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
#  description Ansible Network
#  vrf custB
#  ipv4 address 10.10.0.2 255.255.255.0
#  duplex half
#  shutdown
# !
# interface GigabitEthernet0/0/0/4
# description Test description
#  dot1q native vlan 40
#  l2transport
#   l2protocol stp forward
#  !
# !
# interface GigabitEthernet0/0/0/3.900
#  dot1q vlan 20 any
# !

# Using deleted
#
# Before state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
#  description Ansible Network
#  vrf custB
#  ipv4 address 10.10.0.2 255.255.255.0
#  duplex half
#  shutdown
#  dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
#  description Test description
#  dot1q native vlan 10
#  l2transport
#   l2protocol stp tunnel
#  !
# !
#

- name: "Delete L2 attributes of given interfaces (Note: This won't delete the interface itself)"
  cisco.iosxr.iosxr_l2_interfaces:
    config:
    - name: GigabitEthernet0/0/0/4
    state: deleted

# After state:
# ------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
#  description Ansible Network
#  vrf custB
#  ipv4 address 10.10.0.2 255.255.255.0
#  duplex half
#  shutdown
#  dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
#  description Test description
# !

# Using Deleted without any config passed
# "(NOTE: This will delete all of configured resource module attributes from each configured interface)"
#
# Before state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
#  description Ansible Network
#  vrf custB
#  ipv4 address 10.10.0.2 255.255.255.0
#  duplex half
#  shutdown
#  dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
#  description Test description
#  dot1q native vlan 10
#  l2transport
#   l2protocol stp tunnel
#  !
# !

- name: "Delete L2 attributes of all interfaces (Note: This won't delete the interface itself)"
  cisco.iosxr.iosxr_l2_interfaces:
    state: deleted

# After state:
# ------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
#  description Ansible Network
#  vrf custB
#  ipv4 address 10.10.0.2 255.255.255.0
#  duplex half
#  shutdown
# !
# interface GigabitEthernet0/0/0/4
#  description Test description
# !


# Using parsed
# parsed.cfg
# ------------
#
# interface Loopback888
#  description test for ansible
#  shutdown
# !
# interface MgmtEth0/0/CPU0/0
#  ipv4 address 10.8.38.70 255.255.255.0
# !
# interface GigabitEthernet0/0/0/0
#  description Configured and Merged by Ansible-Network
#  mtu 110
#  ipv4 address 172.31.1.1 255.255.255.0
#  duplex half
# !
# interface GigabitEthernet0/0/0/1
#  dot1q native vlan 10
#  l2transport
#   l2protocol cdp forward
#   l2protocol pvst tunnel
#   propagate remote-status
#  !
# !
# interface GigabitEthernet0/0/0/3
#  shutdown
# !
# interface GigabitEthernet0/0/0/3.900
#  encapsulation dot1q 20 second-dot1q 40
# !
# interface GigabitEthernet0/0/0/4
#  shutdown
#  dot1q native vlan 40
# !
- name: Convert L2 interfaces config to argspec without connecting to the appliance
  cisco.iosxr.iosxr_l2_interfaces:
    running_config: "{{ lookup('file', './parsed.cfg') }}"
    state: parsed
# Task Output (redacted)
# -----------------------
# "parsed": [
#         {
#             "name": "GigabitEthernet0/0/0/0"
#         },
#         {
#             "l2protocol": [
#                 {
#                     "cdp": "forward"
#                 },
#                 {
#                     "pvst": "tunnel"
#                 }
#             ],
#             "l2transport": true,
#             "name": "GigabitEthernet0/0/0/1",
#             "native_vlan": 10,
#             "propagate": true
#         },
#         {
#             "name": "GigabitEthernet0/0/0/3"
#         },
#         {
#             "name": "GigabitEthernet0/0/0/3.900",
#             "q_vlan": [
#                 20,
#                 40
#             ]
#         },
#         {
#             "name": "GigabitEthernet0/0/0/4",
#             "native_vlan": 40
#         }
#     ]


# Using rendered
- name: Render platform specific commands from task input using rendered state
  cisco.iosxr.iosxr_l2_interfaces:
    config:

    - name: GigabitEthernet0/0/0/1
      native_vlan: 10
      l2transport: true
      l2protocol:

      - pvst: tunnel

      - cdp: forward
      propagate: true

    - name: GigabitEthernet0/0/0/3.900
      q_vlan:
      - 20
      - 40

    - name: GigabitEthernet0/0/0/4
      native_vlan: 40
    state: rendered
# Task Output (redacted)
# -----------------------
# "rendered": [
#         "interface GigabitEthernet0/0/0/1",
#         "dot1q native vlan 10",
#         "l2transport l2protocol pvst tunnel",
#         "l2transport l2protocol cdp forward",
#         "l2transport propagate remote-status",
#         "interface GigabitEthernet0/0/0/3.900",
#         "dot1q vlan 20 40",
#         "interface GigabitEthernet0/0/0/4",
#         "dot1q native vlan 40"
#     ]


# Using gathered
# Before state:
# ------------
#
# RP/0/0/CPU0:an-iosxr-02#show running-config  interface
# interface Loopback888
#  description test for ansible
#  shutdown
# !
# interface MgmtEth0/0/CPU0/0
#  ipv4 address 10.8.38.70 255.255.255.0
# !
# interface GigabitEthernet0/0/0/0
#  description Configured and Merged by Ansible-Network
#  mtu 110
#  ipv4 address 172.31.1.1 255.255.255.0
#  duplex half
# !
# interface GigabitEthernet0/0/0/1
#  dot1q native vlan 10
#  l2transport
#   l2protocol cdp forward
#   l2protocol pvst tunnel
#   propagate remote-status
#  !
# !
# interface GigabitEthernet0/0/0/3
#  shutdown
# !
# interface GigabitEthernet0/0/0/3.900
#  encapsulation dot1q 20 second-dot1q 40
# !
# interface GigabitEthernet0/0/0/4
#  shutdown
#  dot1q native vlan 40
# !
- name: Gather IOSXR l2 interfaces as in given arguments
  cisco.iosxr.iosxr_l2_interfaces:
    config:
    state: gathered
# Task Output (redacted)
# -----------------------
#
# "gathered": [
#         {
#             "name": "GigabitEthernet0/0/0/0"
#         },
#         {
#             "l2protocol": [
#                 {
#                     "cdp": "forward"
#                 },
#                 {
#                     "pvst": "tunnel"
#                 }
#             ],
#             "l2transport": true,
#             "name": "GigabitEthernet0/0/0/1",
#             "native_vlan": 10,
#             "propagate": true
#         },
#         {
#             "name": "GigabitEthernet0/0/0/3"
#         },
#         {
#             "name": "GigabitEthernet0/0/0/3.900",
#             "q_vlan": [
#                 20,
#                 40
#             ]
#         },
#         {
#             "name": "GigabitEthernet0/0/0/4",
#             "native_vlan": 40
#         }
#     ]
# After state:
# ------------
#
# RP/0/0/CPU0:an-iosxr-02#show running-config  interface
# interface Loopback888
#  description test for ansible
#  shutdown
# !
# interface MgmtEth0/0/CPU0/0
#  ipv4 address 10.8.38.70 255.255.255.0
# !
# interface GigabitEthernet0/0/0/0
#  description Configured and Merged by Ansible-Network
#  mtu 110
#  ipv4 address 172.31.1.1 255.255.255.0
#  duplex half
# !
# interface GigabitEthernet0/0/0/1
#  dot1q native vlan 10
#  l2transport
#   l2protocol cdp forward
#   l2protocol pvst tunnel
#   propagate remote-status
#  !
# !
# interface GigabitEthernet0/0/0/3
#  shutdown
# !
# interface GigabitEthernet0/0/0/3.900
#  encapsulation dot1q 20 second-dot1q 40
# !
# interface GigabitEthernet0/0/0/4
#  shutdown
#  dot1q native vlan 40
# !

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key

Description

after

list / elements=string

The configuration as structured data after module completion.

Returned: when changed

Sample: “The configuration returned will always be in the same format of the parameters above.”

before

list / elements=string

The configuration as structured data prior to module invocation.

Returned: always

Sample: “The configuration returned will always be in the same format of the parameters above.”

commands

list / elements=string

The set of commands pushed to the remote device

Returned: always

Sample: [“interface GigabitEthernet0/0/0/2”, “l2transport l2protocol pvst tunnel”]

Authors

  • Sumit Jaiswal (@justjais)

  • Rohit Thakur (@rohitthakur2590)