cisco.iosxr.iosxr_lag_interfaces module – Resource module to configure LAG interfaces.
Note
This module is part of the cisco.iosxr collection (version 10.2.2).
You might already have this collection installed if you are using the ansible package.
It is not included in ansible-core.
To check whether it is installed, run ansible-galaxy collection list.
To install it, use: ansible-galaxy collection install cisco.iosxr.
To use it in a playbook, specify: cisco.iosxr.iosxr_lag_interfaces.
New in cisco.iosxr 1.0.0
Synopsis
This module manages the attributes of LAG/Ether-Bundle interfaces on IOS-XR devices.
Parameters
Parameter |
Comments |
|---|---|
A provided Link Aggregation Group (LAG) configuration. |
|
This dict contains configurable options related to LAG/Ether-Bundle links. |
|
Specifies the limit on the number of links that can be active in the LAG/Ether-Bundle. Refer to vendor documentation for valid values. |
|
Specifies the minimum number of active links needed to bring up the LAG/Ether-Bundle. Refer to vendor documentation for valid values. |
|
Specifies the hash function used for traffic forwarded over the LAG/Ether-Bundle. Option ‘dst-ip’ uses the destination IP as the hash function. Option ‘src-ip’ uses the source IP as the hash function. Choices:
|
|
List of member interfaces for the LAG/Ether-Bundle. |
|
Name of the member interface. |
|
Specifies the mode of the operation for the member interface. Mode ‘active’ runs LACP in active mode. Mode ‘on’ does not run LACP over the port. Mode ‘passive’ runs LACP in passive mode over the port. Mode ‘inherit’ runs LACP as configured in the bundle. Choices:
|
|
LAG mode. Mode ‘active’ runs LACP in active mode over the port. Mode ‘on’ does not run LACP over the port. Mode ‘passive’ runs LACP in passive mode over the port. Choices:
|
|
Name/Identifier of the LAG/Ether-Bundle to configure. |
|
This option is used only with state parsed. The value of this option should be the output received from the IOS-XR device by executing the command show running-config int. The state parsed reads the configuration from |
|
The state of the configuration after module completion. Choices:
|
Notes
Note
This module works with connection
network_cli. See the IOS-XR Platform Options.
Examples
# Using merged
#
#
# ------------
# Before state
# ------------
#
# RP/0/0/CPU0:iosxr01#show run int
# Sun Jul 7 19:42:59.416 UTC
# interface Loopback888
# description test for ansible
# shutdown
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 192.0.2.11 255.255.255.0
# !
# interface GigabitEthernet0/0/0/1
# description "GigabitEthernet - 1"
# !
# interface GigabitEthernet0/0/0/2
# description "GigabitEthernet - 2"
# !
# interface GigabitEthernet0/0/0/3
# description "GigabitEthernet - 3"
# !
# interface GigabitEthernet0/0/0/4
# description "GigabitEthernet - 4"
# !
#
#
- name: Merge provided configuration with device configuration
cisco.iosxr.iosxr_lag_interfaces:
config:
- name: Bundle-Ether10
members:
- member: GigabitEthernet0/0/0/1
mode: inherit
- member: GigabitEthernet0/0/0/3
mode: inherit
mode: active
links:
max_active: 5
min_active: 2
load_balancing_hash: src-ip
- name: Bundle-Ether12
members:
- member: GigabitEthernet0/0/0/2
mode: passive
- member: GigabitEthernet0/0/0/4
mode: passive
load_balancing_hash: dst-ip
state: merged
#
#
# -----------
# After state
# -----------
#
# RP/0/0/CPU0:iosxr01#show run int
# Sun Jul 7 20:51:17.685 UTC
# interface Bundle-Ether10
# lacp mode active
# bundle load-balancing hash src-ip
# bundle maximum-active links 5
# bundle minimum-active links 2
# !
# interface Bundle-Ether12
# bundle load-balancing hash dst-ip
# !
# interface Loopback888
# description test for ansible
# shutdown
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 192.0.2.11 255.255.255.0
# !
# interface GigabitEthernet0/0/0/1
# description 'GigabitEthernet - 1"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/2
# description "GigabitEthernet - 2"
# bundle id 12 mode passive
# !
# interface GigabitEthernet0/0/0/3
# description "GigabitEthernet - 3"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/4
# description "GigabitEthernet - 4"
# bundle id 12 mode passive
# !
#
# Using replaced
#
#
# -------------
# Before state
# -------------
#
#
# RP/0/0/CPU0:iosxr01#sho run int
# Sun Jul 7 20:58:06.527 UTC
# interface Bundle-Ether10
# lacp mode active
# bundle load-balancing hash src-ip
# bundle maximum-active links 5
# bundle minimum-active links 2
# !
# interface Bundle-Ether12
# bundle load-balancing hash dst-ip
# !
# interface Loopback888
# description test for ansible
# shutdown
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 192.0.2.11 255.255.255.0
# !
# interface GigabitEthernet0/0/0/1
# description 'GigabitEthernet - 1"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/2
# description "GigabitEthernet - 2"
# bundle id 12 mode passive
# !
# interface GigabitEthernet0/0/0/3
# description "GigabitEthernet - 3"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/4
# description "GigabitEthernet - 4"
# bundle id 12 mode passive
# !
#
#
- name: Replace device configuration of listed Bundles with provided configurations
cisco.iosxr.iosxr_lag_interfaces:
config:
- name: Bundle-Ether12
members:
- name: GigabitEthernet0/0/0/2
mode: passive
- name: Bundle-Ether11
members:
- name: GigabitEthernet0/0/0/4
load_balancing_hash: src-ip
state: replaced
#
#
# -----------
# After state
# -----------
#
#
# RP/0/0/CPU0:iosxr01#sh run int
# Sun Jul 7 21:22:27.397 UTC
# interface Bundle-Ether10
# lacp mode active
# bundle load-balancing hash src-ip
# bundle maximum-active links 5
# bundle minimum-active links 2
# !
# interface Bundle-Ether11
# bundle load-balancing hash src-ip
# !
# interface Bundle-Ether12
# lacp mode passive
# !
# interface Loopback888
# description test for ansible
# shutdown
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 192.0.2.11 255.255.255.0
# !
# interface GigabitEthernet0/0/0/1
# description 'GigabitEthernet - 1"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/2
# description "GigabitEthernet - 2"
# bundle id 12 mode on
# !
# interface GigabitEthernet0/0/0/3
# description "GigabitEthernet - 3"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/4
# description "GigabitEthernet - 4"
# bundle id 11 mode on
# !
#
#
# Using overridden
#
#
# ------------
# Before state
# ------------
#
#
# RP/0/0/CPU0:iosxr01#sh run int
# Sun Jul 7 21:22:27.397 UTC
# interface Bundle-Ether10
# lacp mode active
# bundle load-balancing hash src-ip
# bundle maximum-active links 5
# bundle minimum-active links 2
# !
# interface Bundle-Ether11
# bundle load-balancing hash src-ip
# !
# interface Bundle-Ether12
# lacp mode passive
# !
# interface Loopback888
# description test for ansible
# shutdown
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 192.0.2.11 255.255.255.0
# !
# interface GigabitEthernet0/0/0/1
# description 'GigabitEthernet - 1"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/2
# description "GigabitEthernet - 2"
# bundle id 12 mode on
# !
# interface GigabitEthernet0/0/0/3
# description "GigabitEthernet - 3"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/4
# description "GigabitEthernet - 4"
# bundle id 11 mode on
# !
#
#
- name: Overrides all device configuration with provided configuration
cisco.iosxr.iosxr_lag_interfaces:
config:
- name: Bundle-Ether10
members:
- member: GigabitEthernet0/0/0/1
mode: inherit
- member: GigabitEthernet0/0/0/2
mode: inherit
mode: active
load_balancing_hash: dst-ip
state: overridden
#
#
# ------------
# After state
# ------------
#
#
# RP/0/0/CPU0:iosxr01#sh run int
# Sun Jul 7 21:43:04.802 UTC
# interface Bundle-Ether10
# lacp mode active
# bundle load-balancing hash dst-ip
# !
# interface Bundle-Ether11
# !
# interface Bundle-Ether12
# !
# interface Loopback888
# description test for ansible
# shutdown
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 192.0.2.11 255.255.255.0
# !
# interface GigabitEthernet0/0/0/1
# description 'GigabitEthernet - 1"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/2
# description "GigabitEthernet - 2"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/3
# description "GigabitEthernet - 3"
# !
# interface GigabitEthernet0/0/0/4
# description "GigabitEthernet - 4"
# !
#
#
# Using deleted
#
#
# ------------
# Before state
# ------------
#
# RP/0/0/CPU0:iosxr01#sh run int
# Sun Jul 7 21:22:27.397 UTC
# interface Bundle-Ether10
# lacp mode active
# bundle load-balancing hash src-ip
# bundle maximum-active links 5
# bundle minimum-active links 2
# !
# interface Bundle-Ether11
# bundle load-balancing hash src-ip
# !
# interface Bundle-Ether12
# lacp mode passive
# !
# interface Loopback888
# description test for ansible
# shutdown
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 192.0.2.11 255.255.255.0
# !
# interface GigabitEthernet0/0/0/1
# description 'GigabitEthernet - 1"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/2
# description "GigabitEthernet - 2"
# bundle id 12 mode on
# !n
# interface GigabitEthernet0/0/0/3
# description "GigabitEthernet - 3"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/4
# description "GigabitEthernet - 4"
# bundle id 11 mode on
# !
#
#
- name: >-
Delete attributes of given bundles and removes member interfaces from them
(Note - This won't delete the bundles themselves)
cisco.iosxr.iosxr_lag_interfaces:
config:
- name: Bundle-Ether10
- name: Bundle-Ether11
- name: Bundle-Ether12
state: deleted
#
#
# ------------
# After state
# ------------
#
# RP/0/0/CPU0:iosxr01#sh run int
# Sun Jul 7 21:49:50.004 UTC
# interface Bundle-Ether10
# !
# interface Bundle-Ether11
# !
# interface Bundle-Ether12
# !
# interface Loopback888
# description test for ansible
# shutdown
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 192.0.2.11 255.255.255.0
# !
# interface GigabitEthernet0/0/0/1
# description 'GigabitEthernet - 1"
# !
# interface GigabitEthernet0/0/0/2
# description "GigabitEthernet - 2"
# !
# interface GigabitEthernet0/0/0/3
# description "GigabitEthernet - 3"
# !
# interface GigabitEthernet0/0/0/4
# description "GigabitEthernet - 4"
# !
#
#
# Using deleted (without config)
#
#
# ------------
# Before state
# ------------
#
# RP/0/0/CPU0:an-iosxr#sh run int
# Sun Aug 18 19:49:51.908 UTC
# interface Bundle-Ether10
# lacp mode active
# bundle load-balancing hash src-ip
# bundle maximum-active links 10
# bundle minimum-active links 2
# !
# interface Bundle-Ether11
# bundle load-balancing hash dst-ip
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 192.0.2.11 255.255.255.0
# !
# interface GigabitEthernet0/0/0/0
# shutdown
# !
# interface GigabitEthernet0/0/0/1
# bundle id 10 mode inherit
# shutdown
# !
# interface GigabitEthernet0/0/0/2
# bundle id 10 mode passive
# shutdown
# !
# interface GigabitEthernet0/0/0/3
# bundle id 11 mode passive
# shutdown
# !
# interface GigabitEthernet0/0/0/4
# bundle id 11 mode passive
# shutdown
# !
#
- name: Delete attributes of all bundles and removes member interfaces from them (Note
- This won't delete the bundles themselves)
cisco.iosxr.iosxr_lag_interfaces:
state: deleted
#
#
# ------------
# After state
# ------------
#
#
# RP/0/0/CPU0:an-iosxr#sh run int
# Sun Aug 18 19:54:22.389 UTC
# interface Bundle-Ether10
# !
# interface Bundle-Ether11
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 10.8.38.69 255.255.255.0
# !
# interface GigabitEthernet0/0/0/0
# shutdown
# !
# interface GigabitEthernet0/0/0/1
# shutdown
# !
# interface GigabitEthernet0/0/0/2
# shutdown
# !
# interface GigabitEthernet0/0/0/3
# shutdown
# !
# interface GigabitEthernet0/0/0/4
# shutdown
# !
# Using parsed:
# parsed.cfg
# interface Bundle-Ether10
# lacp mode active
# bundle load-balancing hash src-ip
# bundle maximum-active links 5
# bundle minimum-active links 2
# !
# interface Bundle-Ether12
# bundle load-balancing hash dst-ip
# !
# interface Loopback888
# description test for ansible
# shutdown
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 192.0.2.11 255.255.255.0
# !
# interface GigabitEthernet0/0/0/1
# description 'GigabitEthernet - 1"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/2
# description "GigabitEthernet - 2"
# bundle id 12 mode passive
# !
# interface GigabitEthernet0/0/0/3
# description "GigabitEthernet - 3"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/4
# description "GigabitEthernet - 4"
# bundle id 12 mode passive
# !
#
- name: Convert lag interfaces config to argspec without connecting to the appliance
cisco.iosxr.iosxr_lag_interfaces:
running_config: "{{ lookup('file', './parsed.cfg') }}"
state: parsed
# --------------
# Output
# --------------
# parsed:
# - name: Bundle-Ether10
# members:
# - member: GigabitEthernet0/0/0/1
# mode: inherit
# - member: GigabitEthernet0/0/0/3
# mode: inherit
# mode: active
# links:
# max_active: 5
# min_active: 2
# load_balancing_hash: src-ip
# - name: Bundle-Ether12
# members:
# - member: GigabitEthernet0/0/0/2
# mode: passive
# - member: GigabitEthernet0/0/0/4
# mode: passive
# load_balancing_hash: dst-ip
# using gathered
# Device Config:
# -------------
# interface Bundle-Ether10
# lacp mode active
# bundle load-balancing hash src-ip
# bundle maximum-active links 5
# bundle minimum-active links 2
# !
# interface Bundle-Ether12
# bundle load-balancing hash dst-ip
# !
# interface Loopback888
# description test for ansible
# shutdown
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 192.0.2.11 255.255.255.0
# !
# interface GigabitEthernet0/0/0/1
# description 'GigabitEthernet - 1"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/2
# description "GigabitEthernet - 2"
# bundle id 12 mode passive
# !
# interface GigabitEthernet0/0/0/3
# description "GigabitEthernet - 3"
# bundle id 10 mode inherit
# !
# interface GigabitEthernet0/0/0/4
# description "GigabitEthernet - 4"
# bundle id 12 mode passive
# !
#
- name: Gather IOSXR lag interfaces configuration
cisco.iosxr.iosxr_lag_interfaces:
config:
state: gathered
# --------------
# Output
# --------------
# gathered:
# - name: Bundle-Ether10
# members:
# - member: GigabitEthernet0/0/0/1
# mode: inherit
# - member: GigabitEthernet0/0/0/3
# mode: inherit
# mode: active
# links:
# max_active: 5
# min_active: 2
# load_balancing_hash: src-ip
# - name: Bundle-Ether12
# members:
# - member: GigabitEthernet0/0/0/2
# mode: passive
# - member: GigabitEthernet0/0/0/4
# mode: passive
# load_balancing_hash: dst-ip
# Using rendered:
- name: Render platform specific commands from task input using rendered state
cisco.iosxr.iosxr_lag_interfaces:
config:
- name: Bundle-Ether10
members:
- member: GigabitEthernet0/0/0/1
mode: inherit
- member: GigabitEthernet0/0/0/3
mode: inherit
mode: active
links:
max_active: 5
min_active: 2
load_balancing_hash: src-ip
- name: Bundle-Ether12
members:
- member: GigabitEthernet0/0/0/2
mode: passive
- member: GigabitEthernet0/0/0/4
mode: passive
load_balancing_hash: dst-ip
state: rendered
# Output:
# rendered:
# [
# - "interface Bundle-Ether10"
# - " lacp mode active"
# - " bundle load-balancing hash src-ip"
# - " bundle maximum-active links 5"
# - " bundle minimum-active links 2"
# - "interface Bundle-Ether12"
# - " bundle load-balancing hash dst-ip"
# - "interface Loopback888"
# - " description test for ansible"
# - " shutdown"
# - "interface MgmtEth0/0/CPU0/0"
# - " ipv4 address 192.0.2.11 255.255.255.0"
# - "interface GigabitEthernet0/0/0/1"
# - " description 'GigabitEthernet - 1""
# - " bundle id 10 mode inherit"
# - "interface GigabitEthernet0/0/0/2"
# - " description "GigabitEthernet - 2""
# - " bundle id 12 mode passive"
# - "interface GigabitEthernet0/0/0/3"
# - " description "GigabitEthernet - 3""
# - " bundle id 10 mode inherit"
# - "interface GigabitEthernet0/0/0/4"
# - " description "GigabitEthernet - 4""
# - " bundle id 12 mode passive"
# ]
#
Return Values
Common return values are documented here, the following are the fields unique to this module:
Key |
Description |
|---|---|
The configuration as structured data after module completion. Returned: when changed Sample: |
|
The configuration as structured data prior to module invocation. Returned: always Sample: |
|
The set of commands pushed to the remote device. Returned: always Sample: |