vyos.vyos.vyos_interfaces module – Interfaces resource module

Note

This module is part of the vyos.vyos collection (version 5.0.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install vyos.vyos.

To use it in a playbook, specify: vyos.vyos.vyos_interfaces.

New in vyos.vyos 1.0.0

Synopsis

  • This module manages the interface attributes on VyOS network devices.

  • This module supports managing base attributes of Ethernet, Bonding, VXLAN, Loopback and Virtual Tunnel Interfaces.

Aliases: interfaces

Parameters

Parameter

Comments

config

list / elements=dictionary

The provided interfaces configuration.

description

string

Interface description.

duplex

string

Interface duplex mode.

Applicable for Ethernet interfaces only.

Choices:

  • "full"

  • "half"

  • "auto"

enabled

boolean

Administrative state of the interface.

Set the value to true to administratively enable the interface or false to disable it.

Choices:

  • false

  • true ← (default)

mtu

integer

MTU for a specific interface. Refer to vendor documentation for valid values.

Applicable for Ethernet, Bonding, VXLAN and Virtual Tunnel interfaces.

name

string / required

Full name of the interface, e.g. eth0, eth1, bond0, vti1, vxlan2.

speed

string

Interface link speed.

Applicable for Ethernet interfaces only.

Choices:

  • "auto"

  • "10"

  • "100"

  • "1000"

  • "2500"

  • "10000"

vifs

list / elements=dictionary

Virtual sub-interfaces related configuration.

802.1Q VLAN interfaces are represented as virtual sub-interfaces in VyOS.

description

string

Virtual sub-interface description.

enabled

boolean

Administrative state of the virtual sub-interface.

Set the value to true to administratively enable the interface or false to disable it.

Choices:

  • false

  • true ← (default)

mtu

integer

MTU for the virtual sub-interface.

Refer to vendor documentation for valid values.

vlan_id

integer

Identifier for the virtual sub-interface.

running_config

string

This option is used only with state parsed.

The value of this option should be the output received from the VyOS device by executing the command show configuration commands | grep interfaces.

The state parsed reads the configuration from running_config option and transforms it into Ansible structured data as per the resource module’s argspec and the value is then returned in the parsed key within the result.

state

string

The state of the configuration after module completion.

Choices:

  • "merged" ← (default)

  • "replaced"

  • "overridden"

  • "deleted"

  • "rendered"

  • "gathered"

  • "parsed"

Notes

Note

  • Tested against VyOS 1.1.8 (helium).

  • This module works with connection ansible.netcommon.network_cli. See the VyOS OS Platform Options.

  • The examples use the stdout_callback as yaml to produce task outputs.

Examples

# Using merged

# Before state:
# -------------
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding 'bond0'
# set interfaces bonding 'bond1'
# set interfaces bonding bond2 'ip'
# set interfaces bonding bond2 'ipv6'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 'ip'
# set interfaces ethernet eth0 'ipv6'
# set interfaces ethernet eth0 smp_affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet 'eth1'
# set interfaces ethernet 'eth2'

- name: Merge provided configuration with device configuration
  vyos.vyos.vyos_interfaces:
    config:
      - name: eth2
        description: Configured by Ansible
        enabled: true
        vifs:
          - vlan_id: 200
            description: VIF 200 - ETH2
      - name: eth3
        description: Configured by Ansible
        mtu: 1500
      - name: bond1
        description: Bond - 1
        mtu: 1200
      - name: vti2
        description: VTI - 2
        enabled: false
    state: merged

# Task Output
# -----------
# before:
# - enabled: true
#   name: lo
# - enabled: true
#   name: eth3
# - enabled: true
#   name: eth2
# - enabled: true
#   name: eth1
# - duplex: auto
#   enabled: true
#   name: eth0
#   speed: auto
# commands:
# - set interfaces ethernet eth2 description 'Configured by Ansible'
# - set interfaces ethernet eth2 vif 200
# - set interfaces ethernet eth2 vif 200 description 'VIF 200 - ETH2'
# - set interfaces ethernet eth3 description 'Configured by Ansible'
# - set interfaces ethernet eth3 mtu '1500'
# - set interfaces bonding bond1
# - set interfaces bonding bond1 description 'Bond - 1'
# - set interfaces bonding bond1 mtu '1200'
# - set interfaces vti vti2
# - set interfaces vti vti2 description 'VTI - 2'
# - set interfaces vti vti2 disable
# after:
# - description: Bond - 1
#   enabled: true
#   mtu: 1200
#   name: bond1
# - enabled: true
#   name: lo
# - description: VTI - 2
#   enabled: false
#   name: vti2
# - description: Configured by Ansible
#   enabled: true
#   mtu: 1500
#   name: eth3
# - description: Configured by Ansible
#   enabled: true
#   name: eth2
#   vifs:
#   - description: VIF 200 - ETH2
#     enabled: true
#     vlan_id: '200'
# - enabled: true
#   name: eth1
# - duplex: auto
#   enabled: true
#   name: eth0
#   speed: auto

# After state:
# ------------
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond1 description 'Bond - 1'
# set interfaces bonding bond1 mtu '1200'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 description 'Configured by Ansible'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 vif 200 description 'VIF 200 - ETH2'
# set interfaces ethernet eth3 description 'Configured by Ansible'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 mtu '1500'
# set interfaces loopback lo
# set interfaces vti vti2 description 'VTI - 2'
# set interfaces vti vti2 disable


# Using replaced
# Before state:
# -------------
# vyos:~$ show configuration commands | grep eth
# set interfaces bonding bond1 description 'Bond - 1'
# set interfaces bonding bond1 mtu '1400'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 description 'Management Interface for the Appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:f3:6c:b5'
# set interfaces ethernet eth0 smp_affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Configured by Ansible Eng Team'
# set interfaces ethernet eth1 duplex 'full'
# set interfaces ethernet eth1 hw-id '08:00:27:ad:ef:65'
# set interfaces ethernet eth1 smp_affinity 'auto'
# set interfaces ethernet eth1 speed '100'
# set interfaces ethernet eth2 description 'Configured by Ansible'
# set interfaces ethernet eth2 duplex 'full'
# set interfaces ethernet eth2 hw-id '08:00:27:ab:4e:79'
# set interfaces ethernet eth2 mtu '500'
# set interfaces ethernet eth2 smp_affinity 'auto'
# set interfaces ethernet eth2 speed '100'
# set interfaces ethernet eth2 vif 200 description 'Configured by Ansible'
# set interfaces ethernet eth3 description 'Configured by Ansible'
# set interfaces ethernet eth3 duplex 'full'
# set interfaces ethernet eth3 hw-id '08:00:27:17:3c:85'
# set interfaces ethernet eth3 mtu '1500'
# set interfaces ethernet eth3 smp_affinity 'auto'
# set interfaces ethernet eth3 speed '100'
# set interfaces loopback lo

- name: Replace device configurations of listed interfaces with provided configurations
  vyos.vyos.vyos_interfaces:
    config:
      - name: eth2
        description: Replaced by Ansible
      - name: eth3
        description: Replaced by Ansible
      - name: eth1
        description: Replaced by Ansible
    state: replaced

# Task Output
# -----------
# before:
# - description: Bond - 1
#   enabled: true
#   mtu: 1400
#   name: bond1
# - enabled: true
#   name: lo
# - description: Configured by Ansible
#   duplex: full
#   enabled: true
#   mtu: 1500
#   name: eth3
#   speed: '100'
# - description: Configured by Ansible
#   duplex: full
#   enabled: true
#   mtu: 500
#   name: eth2
#   speed: '100'
#   vifs:
#   - description: VIF 200 - ETH2
#     enabled: true
#     vlan_id: '200'
# - description: Configured by Ansible Eng Team
#   duplex: full
#   enabled: true
#   name: eth1
#   speed: '100'
# - description: Management Interface for the Appliance
#   duplex: auto
#   enabled: true
#   name: eth0
#   speed: auto
# commands:
# - delete interfaces ethernet eth2 speed
# - delete interfaces ethernet eth2 duplex
# - delete interfaces ethernet eth2 mtu
# - delete interfaces ethernet eth2 vif 200 description
# - set interfaces ethernet eth2 description 'Replaced by Ansible'
# - delete interfaces ethernet eth3 speed
# - delete interfaces ethernet eth3 duplex
# - delete interfaces ethernet eth3 mtu
# - set interfaces ethernet eth3 description 'Replaced by Ansible'
# - delete interfaces ethernet eth1 speed
# - delete interfaces ethernet eth1 duplex
# - set interfaces ethernet eth1 description 'Replaced by Ansible'
# after:
# - description: Bond - 1
#   enabled: true
#   mtu: 1400
#   name: bond1
# - enabled: true
#   name: lo
# - description: Replaced by Ansible
#   enabled: true
#   name: eth3
# - description: Replaced by Ansible
#   enabled: true
#   name: eth2
#   vifs:
#   - enabled: true
#     vlan_id: '200'
# - description: Replaced by Ansible
#   enabled: true
#   name: eth1
# - description: Management Interface for the Appliance
#   duplex: auto
#   enabled: true
#   name: eth0
#   speed: auto

# After state:
# ------------
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond1 description 'Bond - 1'
# set interfaces bonding bond1 mtu '1400'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Management Interface for the Appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Replaced by Ansible'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 description 'Replaced by Ansible'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 vif 200
# set interfaces ethernet eth3 description 'Replaced by Ansible'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo


# Using overridden

# Before state:
# -------------
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Ethernet Interface - 0'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 mtu '1200'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Configured by Ansible Eng Team'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 mtu '100'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth1 vif 100 description 'VIF 100 - ETH1'
# set interfaces ethernet eth1 vif 100 disable
# set interfaces ethernet eth2 description 'Configured by Ansible Team (Admin Down)'
# set interfaces ethernet eth2 disable
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 mtu '600'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth3 description 'Configured by Ansible Network'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo
# set interfaces vti vti1 description 'Virtual Tunnel Interface - 1'
# set interfaces vti vti1 mtu '68'

- name: Overrides all device configuration with provided configuration
  vyos.vyos.vyos_interfaces:
    config:
      - name: eth0
        description: Outbound Interface For The Appliance
        speed: auto
        duplex: auto
      - name: eth2
        speed: auto
        duplex: auto
      - name: eth3
        mtu: 1200
    state: overridden

# Task Output
# -----------
# before:
# - enabled: true
#   name: lo
# - description: Virtual Tunnel Interface - 1
#   enabled: true
#   mtu: 68
#   name: vti1
# - description: Configured by Ansible Network
#   enabled: true
#   name: eth3
# - description: Configured by Ansible Team (Admin Down)
#   enabled: false
#   mtu: 600
#   name: eth2
# - description: Configured by Ansible Eng Team
#   enabled: true
#   mtu: 100
#   name: eth1
#   vifs:
#   - description: VIF 100 - ETH1
#     enabled: false
#     vlan_id: '100'
# - description: Ethernet Interface - 0
#   duplex: auto
#   enabled: true
#   mtu: 1200
#   name: eth0
#   speed: auto
# commands:
# - delete interfaces vti vti1 description
# - delete interfaces vti vti1 mtu
# - delete interfaces ethernet eth1 description
# - delete interfaces ethernet eth1 mtu
# - delete interfaces ethernet eth1 vif 100 description
# - delete interfaces ethernet eth1 vif 100 disable
# - delete interfaces ethernet eth0 mtu
# - set interfaces ethernet eth0 description 'Outbound Interface For The Appliance'
# - delete interfaces ethernet eth2 description
# - delete interfaces ethernet eth2 mtu
# - set interfaces ethernet eth2 duplex 'auto'
# - delete interfaces ethernet eth2 disable
# - set interfaces ethernet eth2 speed 'auto'
# - delete interfaces ethernet eth3 description
# - set interfaces ethernet eth3 mtu '1200'
# after:
# - enabled: true
#   name: lo
# - enabled: true
#   name: vti1
# - enabled: true
#   mtu: 1200
#   name: eth3
# - duplex: auto
#   enabled: true
#   name: eth2
#   speed: auto
# - enabled: true
#   name: eth1
#   vifs:
#   - enabled: true
#     vlan_id: '100'
# - description: Outbound Interface For The Appliance
#   duplex: auto
#   enabled: true
#   name: eth0
#   speed: auto

# After state:
# ------------
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Outbound Interface For The Appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth1 vif 100
# set interfaces ethernet eth2 duplex 'auto'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 speed 'auto'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 mtu '1200'
# set interfaces loopback lo
# set interfaces vti vti1


# Using deleted

# Before state:
# -------------
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond0 mtu '1300'
# set interfaces bonding bond1 description 'LAG - 1'
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Outbound Interface for this appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Configured by Ansible Network'
# set interfaces ethernet eth1 duplex 'full'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth1 speed '100'
# set interfaces ethernet eth2 description 'Configured by Ansible'
# set interfaces ethernet eth2 disable
# set interfaces ethernet eth2 duplex 'full'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 mtu '600'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth2 speed '100'
# set interfaces ethernet eth3 description 'Configured by Ansible Network'
# set interfaces ethernet eth3 duplex 'full'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 speed '100'
# set interfaces loopback lo

- name: Delete attributes of given interfaces (Note - This won't delete the interfaces
    themselves)
  vyos.vyos.vyos_interfaces:
    config:
      - name: bond1
      - name: eth1
      - name: eth2
      - name: eth3
    state: deleted

# Task Output
# -----------
# before:
# - enabled: true
#   mtu: 1300
#   name: bond0
# - description: LAG - 1
#   enabled: true
#   name: bond1
# - enabled: true
#   name: lo
# - description: Configured by Ansible Network
#   duplex: full
#   enabled: true
#   name: eth3
#   speed: '100'
# - description: Configured by Ansible
#   duplex: full
#   enabled: false
#   mtu: 600
#   name: eth2
#   speed: '100'
# - description: Configured by Ansible Network
#   duplex: full
#   enabled: true
#   name: eth1
#   speed: '100'
# - description: Outbound Interface for this appliance
#   duplex: auto
#   enabled: true
#   name: eth0
#   speed: auto
# commands:
# - delete interfaces bonding bond1 description
# - delete interfaces ethernet eth1 speed
# - delete interfaces ethernet eth1 duplex
# - delete interfaces ethernet eth1 description
# - delete interfaces ethernet eth2 speed
# - delete interfaces ethernet eth2 disable
# - delete interfaces ethernet eth2 duplex
# - delete interfaces ethernet eth2 disable
# - delete interfaces ethernet eth2 description
# - delete interfaces ethernet eth2 disable
# - delete interfaces ethernet eth2 mtu
# - delete interfaces ethernet eth2 disable
# - delete interfaces ethernet eth3 speed
# - delete interfaces ethernet eth3 duplex
# - delete interfaces ethernet eth3 description
# after:
# - enabled: true
#   mtu: 1300
#   name: bond0
# - enabled: true
#   name: bond1
# - enabled: true
#   name: lo
# - enabled: true
#   name: eth3
# - enabled: true
#   name: eth2
# - enabled: true
#   name: eth1
# - description: Outbound Interface for this appliance
#   duplex: auto
#   enabled: true
#   name: eth0
#   speed: auto

# After state:
# ------------
# vyos@vyos:~$ show configuration commands | grep interfaces
# set interfaces bonding bond0 mtu '1300'
# set interfaces bonding bond1
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 description 'Outbound Interface for this appliance'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ea:0f:b9'
# set interfaces ethernet eth1 smp-affinity 'auto'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth2 smp-affinity 'auto'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces loopback lo


# Using gathered

# Before state:
# -------------
# vyos@192# run show configuration commands | grep interfaces
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:50:5e:19'
# set interfaces ethernet eth0 smp_affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 description 'Configured by Ansible'
# set interfaces ethernet eth1 duplex 'auto'
# set interfaces ethernet eth1 mtu '1500'
# set interfaces ethernet eth1 speed 'auto'
# set interfaces ethernet eth1 vif 200 description 'VIF - 200'
# set interfaces ethernet eth2 description 'Configured by Ansible'
# set interfaces ethernet eth2 duplex 'auto'
# set interfaces ethernet eth2 mtu '1500'
# set interfaces ethernet eth2 speed 'auto'
# set interfaces ethernet eth2 vif 200 description 'VIF - 200'
#
- name: Gather listed interfaces with provided configurations
  vyos.vyos.vyos_interfaces:
    state: gathered

# Task output
# -----------
# gathered:
# - description: Configured by Ansible
#   duplex: auto
#   enabled: true
#   mtu: 1500
#   name: eth2
#   speed: auto
#   vifs:
#   - description: VIF - 200
#     enabled: true
#     vlan_id: 200
# - description: Configured by Ansible
#   duplex: auto
#   enabled: true
#   mtu: 1500
#   name: eth1
#   speed: auto
#   vifs:
#   - description: VIF - 200
#     enabled: true
#     vlan_id: 200
# - duplex: auto
#   enabled: true
#   name: eth0
#   speed: auto


# Using rendered

- name: Render the commands for provided  configuration
  vyos.vyos.vyos_interfaces:
    config:
      - name: eth0
        enabled: true
        duplex: auto
        speed: auto
      - name: eth1
        description: Configured by Ansible - Interface 1
        mtu: 1500
        speed: auto
        duplex: auto
        enabled: true
        vifs:
          - vlan_id: 100
            description: Eth1 - VIF 100
            mtu: 400
            enabled: true
          - vlan_id: 101
            description: Eth1 - VIF 101
            enabled: true
      - name: eth2
        description: Configured by Ansible - Interface 2 (ADMIN DOWN)
        mtu: 600
        enabled: false
    state: rendered


# Task Output
# -----------
# rendered:
# - set interfaces ethernet eth0 duplex 'auto'
# - set interfaces ethernet eth0 speed 'auto'
# - delete interfaces ethernet eth0 disable
# - set interfaces ethernet eth1 duplex 'auto'
# - delete interfaces ethernet eth1 disable
# - set interfaces ethernet eth1 speed 'auto'
# - set interfaces ethernet eth1 description 'Configured by Ansible - Interface 1'
# - set interfaces ethernet eth1 mtu '1500'
# - set interfaces ethernet eth1 vif 100 description 'Eth1 - VIF 100'
# - set interfaces ethernet eth1 vif 100 mtu '400'
# - set interfaces ethernet eth1 vif 101 description 'Eth1 - VIF 101'
# - set interfaces ethernet eth2 disable
# - set interfaces ethernet eth2 description 'Configured by Ansible - Interface 2 (ADMIN
#   DOWN)'
# - set interfaces ethernet eth2 mtu '600'


# Using parsed

- name: Parse the configuration.
  vyos.vyos.vyos_interfaces:
    running_config:
      "set interfaces ethernet eth0 address 'dhcp'
       set interfaces ethernet eth0 duplex 'auto'
       set interfaces ethernet eth0 hw-id '08:00:27:50:5e:19'
       set interfaces ethernet eth0 smp_affinity 'auto'
       set interfaces ethernet eth0 speed 'auto'
       set interfaces ethernet eth1 description 'Configured by Ansible'
       set interfaces ethernet eth1 duplex 'auto'
       set interfaces ethernet eth1 mtu '1500'
       set interfaces ethernet eth1 speed 'auto'
       set interfaces ethernet eth1 vif 200 description 'VIF - 200'
       set interfaces ethernet eth2 description 'Configured by Ansible'
       set interfaces ethernet eth2 duplex 'auto'
       set interfaces ethernet eth2 mtu '1500'
       set interfaces ethernet eth2 speed 'auto'
       set interfaces ethernet eth2 vif 200 description 'VIF - 200'"
    state: parsed

# Task output
# -----------
# parsed:
# - description: Configured by Ansible
#   duplex: auto
#   enabled: true
#   mtu: 1500
#   name: eth2
#   speed: auto
#   vifs:
#   - description: VIF - 200
#     enabled: true
#     vlan_id: 200
# - description: Configured by Ansible
#   duplex: auto
#   enabled: true
#   mtu: 1500
#   name: eth1
#   speed: auto
#   vifs:
#   - description: VIF - 200
#     enabled: true
#     vlan_id: 200
# - duplex: auto
#   enabled: true
#   name: eth0
#   speed: auto

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key

Description

after

list / elements=string

The configuration as structured data after module completion.

Returned: when changed

Sample: ["The configuration returned will always be in the same format\n of the parameters above.\n"]

before

list / elements=string

The configuration as structured data prior to module invocation.

Returned: always

Sample: ["The configuration returned will always be in the same format\n of the parameters above.\n"]

commands

list / elements=string

The set of commands pushed to the remote device.

Returned: always

Sample: ["set interfaces ethernet eth1 mtu 1200", "set interfaces ethernet eth2 vif 100 description VIF 100"]

Authors

  • Nilashish Chakraborty (@nilashishc)

  • Rohit Thakur (@rohitthakur2590)