vyos.vyos.vyos_l3_interfaces module – L3 interfaces resource module

Note

This module is part of the vyos.vyos collection (version 5.0.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install vyos.vyos.

To use it in a playbook, specify: vyos.vyos.vyos_l3_interfaces.

New in vyos.vyos 1.0.0

Synopsis

  • This module manages the L3 interface attributes on VyOS network devices.

Aliases: l3_interfaces

Parameters

Parameter

Comments

config

list / elements=dictionary

The provided L3 interfaces configuration.

ipv4

list / elements=dictionary

List of IPv4 addresses of the interface.

address

string

IPv4 address of the interface.

ipv6

list / elements=dictionary

List of IPv6 addresses of the interface.

address

string

IPv6 address of the interface.

name

string / required

Full name of the interface, e.g. eth0, eth1.

vifs

list / elements=dictionary

Virtual sub-interfaces L3 configurations.

ipv4

list / elements=dictionary

List of IPv4 addresses of the virtual interface.

address

string

IPv4 address of the virtual interface.

ipv6

list / elements=dictionary

List of IPv6 addresses of the virtual interface.

address

string

IPv6 address of the virtual interface.

vlan_id

integer

Identifier for the virtual sub-interface.

running_config

string

This option is used only with state parsed.

The value of this option should be the output received from the VyOS device by executing the command show configuration commands | grep -e eth[2,3].

The state parsed reads the configuration from running_config option and transforms it into Ansible structured data as per the resource module’s argspec and the value is then returned in the parsed key within the result.

state

string

The state of the configuration after module completion.

Choices:

  • "merged" ← (default)

  • "replaced"

  • "overridden"

  • "deleted"

  • "parsed"

  • "gathered"

  • "rendered"

Notes

Note

Examples

# Using merged
#
# Before state:
# -------------
#
# vyos:~$ show configuration commands | grep -e eth[2,3]
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 vif 101
# set interfaces ethernet eth3 vif 102

- name: Merge provided configuration with device configuration
  vyos.vyos.vyos_l3_interfaces:
    config:
      - name: eth2
        ipv4:
          - address: 192.0.2.10/28
          - address: 198.51.100.40/27
        ipv6:
          - address: '2001:db8:100::2/32'
          - address: '2001:db8:400::10/32'
      - name: eth3
        ipv4:
          - address: 203.0.113.65/26
        vifs:
          - vlan_id: 101
            ipv4:
              - address: 192.0.2.71/28
              - address: 198.51.100.131/25
          - vlan_id: 102
            ipv6:
              - address: '2001:db8:1000::5/38'
              - address: '2001:db8:1400::3/38'
    state: merged


# After state:
# -------------
#
# vyos:~$ show configuration commands | grep -e eth[2,3]
# set interfaces ethernet eth2 address '192.0.2.10/28'
# set interfaces ethernet eth2 address '198.51.100.40/27'
# set interfaces ethernet eth2 address '2001:db8:100::2/32'
# set interfaces ethernet eth2 address '2001:db8:400::10/32'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth3 address '203.0.113.65/26'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 vif 101 address '192.0.2.71/28'
# set interfaces ethernet eth3 vif 101 address '198.51.100.131/25'
# set interfaces ethernet eth3 vif 102 address '2001:db8:1000::5/38'
# set interfaces ethernet eth3 vif 102 address '2001:db8:1400::3/38'
# set interfaces ethernet eth3 vif 102 address '2001:db8:4000::2/34'


# Using replaced
#
# Before state:
# -------------
#
# vyos:~$ show configuration commands | grep eth
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:EA:0F:B9'
# set interfaces ethernet eth1 address '192.0.2.14/24'
# set interfaces ethernet eth2 address '192.0.2.10/24'
# set interfaces ethernet eth2 address '192.0.2.11/24'
# set interfaces ethernet eth2 address '2001:db8::10/32'
# set interfaces ethernet eth2 address '2001:db8::11/32'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth3 address '198.51.100.10/24'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 vif 101 address '198.51.100.130/25'
# set interfaces ethernet eth3 vif 101 address '198.51.100.131/25'
# set interfaces ethernet eth3 vif 102 address '2001:db8:4000::3/34'
# set interfaces ethernet eth3 vif 102 address '2001:db8:4000::2/34'
#
- name: Replace device configurations of listed interfaces with provided configurations
  vyos.vyos.vyos_l3_interfaces:
    config:
      - name: eth2
        ipv4:
          - address: 192.0.2.10/24

      - name: eth3
        ipv6:
          - address: 2001:db8::11/32
    state: replaced

# After state:
# -------------
#
# vyos:~$ show configuration commands | grep eth
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:EA:0F:B9'
# set interfaces ethernet eth1 address '192.0.2.14/24'
# set interfaces ethernet eth2 address '192.0.2.10/24'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 address '2001:db8::11/32'
# set interfaces ethernet eth3 vif 101
# set interfaces ethernet eth3 vif 102


# Using overridden
#
# Before state
# --------------
#
# vyos@vyos-appliance:~$ show configuration commands | grep eth
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:EA:0F:B9'
# set interfaces ethernet eth1 address '192.0.2.14/24'
# set interfaces ethernet eth2 address '192.0.2.10/24'
# set interfaces ethernet eth2 address '192.0.2.11/24'
# set interfaces ethernet eth2 address '2001:db8::10/32'
# set interfaces ethernet eth2 address '2001:db8::11/32'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth3 address '198.51.100.10/24'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 vif 101 address '198.51.100.130/25'
# set interfaces ethernet eth3 vif 101 address '198.51.100.131/25'
# set interfaces ethernet eth3 vif 102 address '2001:db8:4000::3/34'
# set interfaces ethernet eth3 vif 102 address '2001:db8:4000::2/34'

- name: Overrides all device configuration with provided configuration
  vyos.vyos.vyos_l3_interfaces:
    config:
      - name: eth0
        ipv4:
          - address: dhcp
        ipv6:
          - address: dhcpv6
    state: overridden


# After state
# ------------
#
# vyos@vyos-appliance:~$ show configuration commands | grep eth
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 address 'dhcpv6'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:EA:0F:B9'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 vif 101
# set interfaces ethernet eth3 vif 102


# Using deleted
#
# Before state
# -------------
# vyos@vyos-appliance:~$ show configuration commands | grep eth
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:30:f0:22'
# set interfaces ethernet eth0 smp-affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:EA:0F:B9'
# set interfaces ethernet eth1 address '192.0.2.14/24'
# set interfaces ethernet eth2 address '192.0.2.10/24'
# set interfaces ethernet eth2 address '192.0.2.11/24'
# set interfaces ethernet eth2 address '2001:db8::10/32'
# set interfaces ethernet eth2 address '2001:db8::11/32'
# set interfaces ethernet eth2 hw-id '08:00:27:c2:98:23'
# set interfaces ethernet eth3 address '198.51.100.10/24'
# set interfaces ethernet eth3 hw-id '08:00:27:43:70:8c'
# set interfaces ethernet eth3 vif 101 address '198.51.100.130/25'
# set interfaces ethernet eth3 vif 101 address '198.51.100.131/25'
# set interfaces ethernet eth3 vif 102 address '2001:db8:4000::3/34'
# set interfaces ethernet eth3 vif 102 address '2001:db8:4000::2/34'

- name: Delete L3 attributes of given interfaces (Note - This won't delete the interface
    itself)
  vyos.vyos.vyos_l3_interfaces:
    config:
      - name: eth1
      - name: eth2
      - name: eth3
    state: deleted

# After state
# ------------
# vyos@vyos-appliance:~$ show configuration commands | grep eth
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:f3:6c:b5'
# set interfaces ethernet eth0 smp_affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 hw-id '08:00:27:ad:ef:65'
# set interfaces ethernet eth1 smp_affinity 'auto'
# set interfaces ethernet eth2 hw-id '08:00:27:ab:4e:79'
# set interfaces ethernet eth2 smp_affinity 'auto'
# set interfaces ethernet eth3 hw-id '08:00:27:17:3c:85'
# set interfaces ethernet eth3 smp_affinity 'auto'


# Using gathered
#
# Before state:
# -------------
#
# vyos:~$ show configuration commands | grep -e eth[2,3,0]
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:50:5e:19'
# set interfaces ethernet eth0 smp_affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 address '192.0.2.14/24'
# set interfaces ethernet eth2 address '192.0.2.11/24'
# set interfaces ethernet eth2 address '192.0.2.10/24'
# set interfaces ethernet eth2 address '2001:db8::10/32'
# set interfaces ethernet eth2 address '2001:db8::12/32'
#
- name: Gather listed l3 interfaces with provided configurations
  vyos.vyos.vyos_l3_interfaces:
    state: gathered
#
#
# -------------------------
# Module Execution Result
# -------------------------
#
#    "gathered": [
#         {
#             "ipv4": [
#                 {
#                     "address": "192.0.2.11/24"
#                 },
#                 {
#                     "address": "192.0.2.10/24"
#                 }
#             ],
#             "ipv6": [
#                 {
#                     "address": "2001:db8::10/32"
#                 },
#                 {
#                     "address": "2001:db8::12/32"
#                 }
#             ],
#             "name": "eth2"
#         },
#         {
#             "ipv4": [
#                 {
#                     "address": "192.0.2.14/24"
#                 }
#             ],
#             "name": "eth1"
#         },
#         {
#             "ipv4": [
#                 {
#                     "address": "dhcp"
#                 }
#             ],
#             "name": "eth0"
#         }
#     ]
#
#
# After state:
# -------------
#
# vyos:~$ show configuration commands | grep -e eth[2,3]
# set interfaces ethernet eth0 address 'dhcp'
# set interfaces ethernet eth0 duplex 'auto'
# set interfaces ethernet eth0 hw-id '08:00:27:50:5e:19'
# set interfaces ethernet eth0 smp_affinity 'auto'
# set interfaces ethernet eth0 speed 'auto'
# set interfaces ethernet eth1 address '192.0.2.14/24'
# set interfaces ethernet eth2 address '192.0.2.11/24'
# set interfaces ethernet eth2 address '192.0.2.10/24'
# set interfaces ethernet eth2 address '2001:db8::10/32'
# set interfaces ethernet eth2 address '2001:db8::12/32'


# Using rendered
#
#
- name: Render the commands for provided  configuration
  vyos.vyos.vyos_l3_interfaces:
    config:
      - name: eth1
        ipv4:
          - address: 192.0.2.14/24
      - name: eth2
        ipv4:
          - address: 192.0.2.10/24
          - address: 192.0.2.11/24
        ipv6:
          - address: '2001:db8::10/32'
          - address: '2001:db8::12/32'
    state: rendered

#
#
# -------------------------
# Module Execution Result
# -------------------------
#
#
# "rendered": [
#         "set interfaces ethernet eth1 address '192.0.2.14/24'",
#         "set interfaces ethernet eth2 address '192.0.2.11/24'",
#         "set interfaces ethernet eth2 address '192.0.2.10/24'",
#         "set interfaces ethernet eth2 address '2001:db8::10/32'",
#         "set interfaces ethernet eth2 address '2001:db8::12/32'"
#     ]


# Using parsed
#
#
- name: parse the provided running configuration
  vyos.vyos.vyos_l3_interfaces:
    running_config:
      "set interfaces ethernet eth0 address 'dhcp'
       set interfaces ethernet eth1 address '192.0.2.14/24'
       set interfaces ethernet eth2 address '192.0.2.10/24'
       set interfaces ethernet eth2 address '192.0.2.11/24'
       set interfaces ethernet eth2 address '2001:db8::10/32'
       set interfaces ethernet eth2 address '2001:db8::12/32'"
    state: parsed
#
#
# -------------------------
# Module Execution Result
# -------------------------
#
#
# "parsed": [
#         {
#             "ipv4": [
#                 {
#                     "address": "192.0.2.10/24"
#                 },
#                 {
#                     "address": "192.0.2.11/24"
#                 }
#             ],
#             "ipv6": [
#                 {
#                     "address": "2001:db8::10/32"
#                 },
#                 {
#                     "address": "2001:db8::12/32"
#                 }
#             ],
#             "name": "eth2"
#         },
#         {
#             "ipv4": [
#                 {
#                     "address": "192.0.2.14/24"
#                 }
#             ],
#             "name": "eth1"
#         },
#         {
#             "ipv4": [
#                 {
#                     "address": "dhcp"
#                 }
#             ],
#             "name": "eth0"
#         }
#     ]

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key

Description

after

list / elements=string

The configuration as structured data after module completion.

Returned: when changed

Sample: ["The configuration returned will always be in the same format\n of the parameters above.\n"]

before

list / elements=string

The configuration as structured data prior to module invocation.

Returned: always

Sample: ["The configuration returned will always be in the same format\n of the parameters above.\n"]

commands

list / elements=string

The set of commands pushed to the remote device.

Returned: always

Sample: ["set interfaces ethernet eth1 192.0.2.14/2", "set interfaces ethernet eth3 vif 101 address 198.51.100.130/25"]

Authors

  • Nilashish Chakraborty (@NilashishC)

  • Rohit Thakur (@rohitthakur2590)