cisco.ios.ios_ospfv3 module – Resource module to configure OSPFv3.

Note

This module is part of the cisco.ios collection (version 9.0.3).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install cisco.ios.

To use it in a playbook, specify: cisco.ios.ios_ospfv3.

New in cisco.ios 1.1.0

Synopsis 

This module configures and manages the Open Shortest Path First (OSPF) version 3 on IOS platforms.

Parameters 

Parameter	Comments
config dictionary	A list of configurations for ospfv3.
processes list / elements=dictionary	List of OSPF instance configurations.
address_family list / elements=dictionary	Enter Address Family command mode
adjacency dictionary	Control adjacency formation
disable boolean	Disable adjacency staggering Choices: `false` `true`
max_adjacency integer	Maximum number of adjacencies allowed to be forming Please refer vendor documentation for valid values
min_adjacency integer	Initial number of adjacencies allowed to be forming in an area Please refer vendor documentation for valid values
none boolean	No initial Choices: `false` `true`
afi string	Enter Address Family command mode Choices: `"ipv4"` `"ipv6"`
areas list / elements=dictionary	OSPF area parameters
area_id string	OSPF area ID as a decimal value. Please refer vendor documentation of Valid values. OSPF area ID in IP address format(e.g. A.B.C.D)
authentication dictionary	Authentication parameters
key_chain string	Use a key-chain for cryptographic authentication keys
null boolean	Use no authentication Choices: `false` `true`
default_cost integer	Set the summary default-cost of a NSSA/stub area Stub’s advertised external route metric Note, please refer vendor documentation for respective valid values
filter_list list / elements=dictionary	Filter networks between OSPFv3 areas
direction string / required	The direction to apply on the filter networks sent to and from this area. Choices: `"in"` `"out"`
name string	Name of an IP prefix-list
normal boolean	Specify a normal area type Choices: `false` `true`
nssa dictionary	Specify a NSSA area
default_information_originate dictionary	Originate Type 7 default into NSSA area
metric integer	OSPF default metric
metric_type integer	OSPF metric type for default routes OSPF Link State type Choices: `1` `2`
nssa_only boolean	Limit default advertisement to this NSSA area Choices: `false` `true`
no_redistribution boolean	No redistribution into this NSSA area Choices: `false` `true`
no_summary boolean	Do not send summary LSA into NSSA Choices: `false` `true`
set boolean	Enable a NSSA area Choices: `false` `true`
translate string	Translate LSA Always translate LSAs on this ABR Suppress forwarding address in translated LSAs Choices: `"always"` `"suppress-fa"`
ranges list / elements=dictionary	Summarize routes matching address/mask (border routers only)
address string	IP address to match
advertise boolean	Advertise this range (default) Since, advertise when enabled is not shown in running-config idempotency won’t be maintained for the play in the second or next run of the play. Choices: `false` `true`
cost integer	User specified metric for this range
netmask string	IP mask for address
not_advertise boolean	DoNotAdvertise this range Choices: `false` `true`
sham_link dictionary	Define a sham link and its parameters
authentication dictionary	Authentication parameters
key_chain string	Use a key-chain for cryptographic authentication keys
null boolean	Use no authentication Choices: `false` `true`
cost integer	Associate a cost with the sham-link Cost of the sham-link
destination string	IPv6 address associated with sham-link destination (X:X:X:X::X)
source string	IPv6 address associated with sham-link source (X:X:X:X::X)
ttl_security integer	TTL security check maximum number of hops allowed
stub dictionary	Specify a stub area Backbone can not be configured as stub area
no_summary boolean	Do not send summary LSA into stub area Choices: `false` `true`
set boolean	Enable a stub area Choices: `false` `true`
authentication dictionary	Authentication parameters Authentication operation mode
deployment boolean	Deployment mode of operation Choices: `false` `true`
normal boolean	Normal mode of operation Choices: `false` `true`
auto_cost dictionary	Calculate OSPF interface cost according to bandwidth
reference_bandwidth integer	Use reference bandwidth method to assign OSPF cost Note, refer vendor documentation for respective valid values
set boolean	Enable OSPF auto-cost Choices: `false` `true`
bfd dictionary	BFD configuration commands
all_interfaces boolean	Enable BFD on all interfaces Choices: `false` `true`
disable boolean	Disable BFD on all interfaces Choices: `false` `true`
capability boolean	Enable a specific feature Do not perform PE specific checks Choices: `false` `true`
compatible dictionary	OSPFv3 router compatibility list
rfc1583 boolean	compatible with RFC 1583 Choices: `false` `true`
rfc1587 boolean	compatible with RFC 1587 Choices: `false` `true`
rfc5243 boolean	supports DBD exchange optimization Choices: `false` `true`
default_information dictionary	Control distribution of default information
always boolean	Always advertise default route Choices: `false` `true`
metric integer	OSPF default metric Note, refer vendor documentation for respective valid values
metric_type integer	OSPF metric type for default routes Note, please refer vendor documentation for respective valid range
originate boolean	Distribute a default route Choices: `false` `true`
route_map string	Route-map reference name
default_metric integer	Set metric of redistributed routes
discard_route dictionary	Enable or disable discard-route installation
external boolean	Discard route for summarised redistributed routes Choices: `false` `true`
internal boolean	Discard route for summarised inter-area routes Choices: `false` `true`
sham_link boolean	Discard route for sham-link routes Choices: `false` `true`
distance integer	Define an administrative distance Note, please refer vendor documentation for respective valid range
distribute_list dictionary	Filter networks in routing updates
acls list / elements=dictionary	IP access list
direction string / required	Filter incoming and outgoing routing updates. Choices: `"in"` `"out"`
interface string	Interface configuration (GigabitEthernet A/B) Valid with incoming traffic
name string / required	IP access list name/number
protocol string	Protocol config (bgp 1). Valid with outgoing traffic
prefix dictionary	Filter prefixes in routing updates
direction string / required	Filter incoming and outgoing routing updates. Choices: `"in"` `"out"`
gateway_name string	Gateway name for filtering incoming updates based on gateway
interface string	Interface configuration (GigabitEthernet A/B) Valid with incoming traffic
name string / required	Name of an IP prefix-list
protocol string	Protocol config (bgp 1). Valid with outgoing traffic
route_map dictionary	Filter prefixes in routing updates
name string / required	Route-map name
event_log dictionary	Event Logging
enable boolean	Enable event Logging Choices: `false` `true`
one_shot boolean	Disable Logging When Log Buffer Becomes Full Choices: `false` `true`
pause boolean	Pause Event Logging Choices: `false` `true`
size integer	Maximum Number of Events Stored in the Event Log Note, refer vendor documentation for respective valid values
graceful_restart dictionary	Graceful-restart options helper support
disable boolean	disable helper support Choices: `false` `true`
enable boolean	helper support enabled Choices: `false` `true`
strict_lsa_checking boolean	enable helper strict LSA checking Choices: `false` `true`
interface_id dictionary	Source of the interface ID
ios_if_index boolean	IOS interface number Choices: `false` `true`
snmp_if_index boolean	SNMP MIB ifIndex Choices: `false` `true`
limit dictionary	Limit a specific OSPF feature
dc dictionary	Demand circuit retransmissions
disable boolean	Disble the feature Choices: `false` `true`
number integer	The maximum number of retransmissions
non_dc dictionary	Non-demand-circuit retransmissions
disable boolean	Disble the feature Choices: `false` `true`
number integer	The maximum number of retransmissions
local_rib_criteria dictionary	Enable or disable usage of local RIB as route criteria
enable boolean	Enable usage of local RIB as route criteria Choices: `false` `true`
forwarding_address boolean	Local RIB used to validate external/NSSA forwarding addresses Choices: `false` `true`
inter_area_summary boolean	Local RIB used as criteria for inter-area summaries Choices: `false` `true`
nssa_translation boolean	Local RIB used as criteria for NSSA translation Choices: `false` `true`
log_adjacency_changes dictionary	Log changes in adjacency state
detail boolean	Log all state changes Choices: `false` `true`
set boolean	Log changes in adjacency state Choices: `false` `true`
manet dictionary	Specify MANET OSPF parameters
cache dictionary	Specify MANET cache sizes
acknowledgement integer	Specify MANET acknowledgement cache size Maximum number of acknowledgements in cache
update integer	Specify MANET LSA cache size Maximum number of LSAs in cache
hello dictionary	Unicast Hellos rather than multicast
multicast boolean	Multicast Hello requests and responses rather than unicast Choices: `false` `true`
unicast boolean	Unicast Hello requests and responses rather than multicast Choices: `false` `true`
peering dictionary	MANET OSPF Smart Peering
disable boolean	Disable selective peering Choices: `false` `true`
per_interface boolean	Select peers per interface rather than per node Choices: `false` `true`
redundancy integer	Redundant paths Number of redundant OSPF paths
set boolean	Enable selective peering Choices: `false` `true`
willingness integer	Specify and Relay willingness value
max_lsa dictionary	Maximum number of non self-generated LSAs to accept
ignore_count integer	Maximum number of times adjacencies can be suppressed Note, refer vendor documentation for respective valid values
ignore_time integer	Number of minutes during which all adjacencies are suppressed Note, refer vendor documentation for respective valid values
number integer	Maximum number of non self-generated LSAs to accept Note, refer vendor documentation for respective valid values
reset_time integer	Number of minutes after which ignore-count is reset to zero Note, refer vendor documentation for respective valid values
threshold_value integer	Threshold value (%) at which to generate a warning msg Note, refer vendor documentation for respective valid values
warning_only boolean	Only give a warning message when limit is exceeded Choices: `false` `true`
max_metric dictionary	Set maximum metric Maximum metric in self-originated router-LSAs
disable boolean	disable maximum metric in self-originated router-LSAs Choices: `false` `true`
external_lsa integer	Override external-lsa metric with max-metric value Overriding metric in external-LSAs Note, refer vendor documentation for respective valid values
inter_area_lsas integer	Override inter-area-lsas metric with max-metric value Overriding metric in inter-area-LSAs Note, refer vendor documentation for respective valid values
on_startup dictionary	Set maximum metric temporarily after reboot
time integer	Time, in seconds, router-LSAs are originated with max-metric Note, please refer vendor documentation for respective valid range
wait_for_bgp boolean	Let BGP decide when to originate router-LSA with normal metric Choices: `false` `true`
stub_prefix_lsa boolean	Set maximum metric for stub links in prefix LSAs Choices: `false` `true`
maximum_paths integer	Forward packets over multiple paths Number of paths
passive_interface string	Suppress routing updates on an interface
prefix_suppression dictionary	Prefix suppression
disable boolean	Disable prefix suppression Choices: `false` `true`
enable boolean	Enable prefix suppression Choices: `false` `true`
queue_depth dictionary	Hello/Router process queue depth
hello dictionary	OSPF Hello process queue depth
max_packets integer	maximum number of packets in the queue
unlimited boolean	Unlimited queue depth Choices: `false` `true`
update dictionary	OSPF Router process queue depth
max_packets integer	maximum number of packets in the queue
unlimited boolean	Unlimited queue depth Choices: `false` `true`
router_id string	Router-id address for this OSPF process OSPF router-id in IP address format (A.B.C.D)
shutdown dictionary	Shutdown the router process
disable boolean	Disable Shutdown Choices: `false` `true`
enable boolean	Shutdown the router process Choices: `false` `true`
summary_prefix dictionary	Configure IP address summaries
address string	IP summary address (A.B.C.D) IP prefix <network>/<length> (A.B.C.D/nn)
mask string	IP Summary mask
not_advertise boolean	Do not advertise or translate Choices: `false` `true`
nssa_only boolean	Limit summary to NSSA areas Choices: `false` `true`
tag integer	Set tag
timers dictionary	Adjust routing timers
lsa integer	OSPF LSA timers, arrival timer The minimum interval in milliseconds between accepting the same LSA Note, refer vendor documentation for respective valid values
manet dictionary	OSPF MANET timers
cache dictionary	Specify MANET cache sizes
acknowledgement integer	Specify MANET acknowledgement cache size
redundancy integer	Specify MANET LSA cache size
hello boolean	Unicast Hellos rather than multicast Unicast Hello requests and responses rather than multicast Choices: `false` `true`
peering dictionary	MANET OSPF Smart Peering
per_interface boolean	Select peers per interface rather than per node Choices: `false` `true`
redundancy integer	Redundant paths Number of redundant OSPF paths
set boolean	Enable selective peering Choices: `false` `true`
willingness integer	Specify and Relay willingness value
pacing dictionary	OSPF pacing timers
flood integer	OSPF flood pacing timer The minimum interval in msec to pace limit flooding on interface Note, refer vendor documentation for respective valid values
lsa_group integer	OSPF LSA group pacing timer Interval in sec between group of LSA being refreshed or maxaged Note, refer vendor documentation for respective valid values
retransmission integer	OSPF retransmission pacing timer The minimum interval in msec between neighbor retransmissions Note, refer vendor documentation for respective valid values
throttle dictionary	OSPF throttle timers
lsa dictionary	OSPF LSA throttle timers
first_delay integer	Delay to generate first occurrence of LSA in milliseconds Note, refer vendor documentation for respective valid values
max_delay integer	Maximum delay between originating the same LSA in milliseconds Note, refer vendor documentation for respective valid values
min_delay integer	Minimum delay between originating the same LSA in milliseconds Note, refer vendor documentation for respective valid values
spf dictionary	OSPF SPF throttle timers - Delay between receiving a change to SPF calculation in milliseconds - Note, refer vendor documentation for respective valid values
between_delay integer	Delay between first and second SPF calculation in milliseconds Note, refer vendor documentation for respective valid values
max_delay integer	Maximum wait time in milliseconds for SPF calculations Note, refer vendor documentation for respective valid values
receive_delay integer	Delay between receiving a change to SPF calculation in milliseconds Note, refer vendor documentation for respective valid values
unicast boolean	Address Family modifier Choices: `false` `true`
vrf string	Specify parameters for a VPN Routing/Forwarding instance
adjacency dictionary	Control adjacency formation
max_adjacency integer	Maximum number of adjacencies allowed to be forming Please refer vendor documentation for valid values
min_adjacency integer	Initial number of adjacencies allowed to be forming in an area Please refer vendor documentation for valid values
none boolean	No initial Choices: `false` `true`
areas list / elements=dictionary	OSPF area parameters
area_id string	OSPF area ID as a decimal value. Please refer vendor documentation of Valid values. OSPF area ID in IP address format(e.g. A.B.C.D)
authentication dictionary	Authentication parameters
ipsec dictionary	Use IPsec authentication
hex_string string	SHA-1 key (40 chars)
md5 integer	Use MD5 authentication
sha1 integer	Use SHA-1 authentication
spi integer	Set the SPI (Security Parameters Index)
key_chain string	Use a key-chain for cryptographic authentication keys
default_cost integer	Set the summary default-cost of a NSSA/stub area Stub’s advertised external route metric Note, please refer vendor documentation for respective valid values
nssa dictionary	Specify a NSSA area
default_information_originate dictionary	Originate Type 7 default into NSSA area
metric integer	OSPF default metric
metric_type integer	OSPF metric type for default routes OSPF Link State type Choices: `1` `2`
nssa_only boolean	Limit default advertisement to this NSSA area Choices: `false` `true`
no_redistribution boolean	No redistribution into this NSSA area Choices: `false` `true`
no_summary boolean	Do not send summary LSA into NSSA Choices: `false` `true`
set boolean	Enable a NSSA area Choices: `false` `true`
translate string	Translate LSA Always translate LSAs on this ABR Suppress forwarding address in translated LSAs Choices: `"always"` `"suppress-fa"`
stub dictionary	Specify a stub area Backbone can not be configured as stub area
no_summary boolean	Do not send summary LSA into stub area Choices: `false` `true`
set boolean	Enable a stub area Choices: `false` `true`
authentication boolean	Authentication parameter mode Deployment mode of operation Choices: `false` `true`
auto_cost dictionary	Calculate OSPF interface cost according to bandwidth
reference_bandwidth integer	Use reference bandwidth method to assign OSPF cost Note, refer vendor documentation for respective valid values
set boolean	Enable OSPF auto-cost Choices: `false` `true`
bfd boolean	BFD configuration commands Enable BFD on all interfaces Choices: `false` `true`
compatible dictionary	OSPFv3 router compatibility list
rfc1583 boolean	compatible with RFC 1583 Choices: `false` `true`
rfc1587 boolean	compatible with RFC 1587 Choices: `false` `true`
rfc5243 boolean	supports DBD exchange optimization Choices: `false` `true`
event_log dictionary	Event Logging
enable boolean	Enable event Logging Choices: `false` `true`
one_shot boolean	Disable Logging When Log Buffer Becomes Full Choices: `false` `true`
pause boolean	Pause Event Logging Choices: `false` `true`
size integer	Maximum Number of Events Stored in the Event Log Note, refer vendor documentation for respective valid values
graceful_restart dictionary	Graceful-restart options for helper support
disable boolean	disable helper support Choices: `false` `true`
strict_lsa_checking boolean	enable helper strict LSA checking Choices: `false` `true`
help boolean	Description of the interactive help system Choices: `false` `true`
interface_id boolean	Source of the interface ID SNMP MIB ifIndex Choices: `false` `true`
limit dictionary	Limit a specific OSPF feature and LS update, DBD, and LS request retransmissions
dc dictionary	Demand circuit retransmissions
disable boolean	Disable the feature Choices: `false` `true`
number integer	The maximum number of retransmissions
non_dc dictionary	Non-demand-circuit retransmissions
disable boolean	Disable the feature Choices: `false` `true`
number integer	The maximum number of retransmissions
local_rib_criteria dictionary	Enable or disable usage of local RIB as route criteria
enable boolean	Enable usage of local RIB as route criteria Choices: `false` `true`
forwarding_address boolean	Local RIB used to validate external/NSSA forwarding addresses Choices: `false` `true`
inter_area_summary boolean	Local RIB used as criteria for inter-area summaries Choices: `false` `true`
nssa_translation boolean	Local RIB used as criteria for NSSA translation Choices: `false` `true`
log_adjacency_changes dictionary	Log changes in adjacency state
detail boolean	Log all state changes Choices: `false` `true`
set boolean	Log changes in adjacency state Choices: `false` `true`
manet dictionary	Specify MANET OSPF parameters
cache dictionary	Specify MANET cache sizes
acknowledgement integer	Specify MANET acknowledgement cache size
redundancy integer	Specify MANET LSA cache size
hello boolean	Unicast Hellos rather than multicast Unicast Hello requests and responses rather than multicast Choices: `false` `true`
peering dictionary	MANET OSPF Smart Peering
per_interface boolean	Select peers per interface rather than per node Choices: `false` `true`
redundancy integer	Redundant paths Number of redundant OSPF paths
set boolean	Enable selective peering Choices: `false` `true`
willingness integer	Specify and Relay willingness value
max_lsa dictionary	Maximum number of non self-generated LSAs to accept
ignore_count integer	Maximum number of times adjacencies can be suppressed Note, refer vendor documentation for respective valid values
ignore_time integer	Number of minutes during which all adjacencies are suppressed Note, refer vendor documentation for respective valid values
number integer	Maximum number of non self-generated LSAs to accept Note, refer vendor documentation for respective valid values
reset_time integer	Number of minutes after which ignore-count is reset to zero Note, refer vendor documentation for respective valid values
threshold_value integer	Threshold value (%) at which to generate a warning msg Note, refer vendor documentation for respective valid values
warning_only boolean	Only give a warning message when limit is exceeded Choices: `false` `true`
max_metric dictionary	Set maximum metric
external_lsa integer	Override external-lsa metric with max-metric value Overriding metric in external-LSAs Note, refer vendor documentation for respective valid values
include_stub boolean	Set maximum metric for stub links in router-LSAs Choices: `false` `true`
on_startup dictionary	Set maximum metric temporarily after reboot
time integer	Time, in seconds, router-LSAs are originated with max-metric Note, please refer vendor documentation for respective valid range
wait_for_bgp boolean	Let BGP decide when to originate router-LSA with normal metric Choices: `false` `true`
router_lsa boolean / required	Maximum metric in self-originated router-LSAs Choices: `false` `true`
summary_lsa integer	Override summary-lsa metric with max-metric value Note, please refer vendor documentation for respective valid range
passive_interface string	Suppress routing updates on an interface
prefix_suppression boolean	Enable prefix suppression Choices: `false` `true`
process_id integer / required	Process ID
queue_depth dictionary	Hello/Router process queue depth
hello dictionary	OSPF Hello process queue depth
max_packets integer	maximum number of packets in the queue
unlimited boolean	Unlimited queue depth Choices: `false` `true`
router_id string	Router-id address for this OSPF process OSPF router-id in IP address format (A.B.C.D)
shutdown boolean	Shutdown the router process Choices: `false` `true`
timers dictionary	Adjust routing timers
lsa integer	OSPF LSA timers, arrival timer The minimum interval in milliseconds between accepting the same LSA Note, refer vendor documentation for respective valid values
manet dictionary	OSPF MANET timers
cache dictionary	Specify MANET cache sizes
acknowledgement integer	Specify MANET acknowledgement cache size
redundancy integer	Specify MANET LSA cache size
hello boolean	Unicast Hellos rather than multicast Unicast Hello requests and responses rather than multicast Choices: `false` `true`
peering dictionary	MANET OSPF Smart Peering
per_interface boolean	Select peers per interface rather than per node Choices: `false` `true`
redundancy integer	Redundant paths Number of redundant OSPF paths
set boolean	Enable selective peering Choices: `false` `true`
willingness integer	Specify and Relay willingness value
pacing dictionary	OSPF pacing timers
flood integer	OSPF flood pacing timer The minimum interval in msec to pace limit flooding on interface Note, refer vendor documentation for respective valid values
lsa_group integer	OSPF LSA group pacing timer Interval in sec between group of LSA being refreshed or maxaged Note, refer vendor documentation for respective valid values
retransmission integer	OSPF retransmission pacing timer The minimum interval in msec between neighbor retransmissions Note, refer vendor documentation for respective valid values
throttle dictionary	OSPF throttle timers
lsa dictionary	OSPF LSA throttle timers
first_delay integer	Delay to generate first occurrence of LSA in milliseconds Note, refer vendor documentation for respective valid values
max_delay integer	Maximum delay between originating the same LSA in milliseconds Note, refer vendor documentation for respective valid values
min_delay integer	Minimum delay between originating the same LSA in milliseconds Note, refer vendor documentation for respective valid values
spf dictionary	OSPF SPF throttle timers - Delay between receiving a change to SPF calculation in milliseconds - Note, refer vendor documentation for respective valid values
between_delay integer	Delay between first and second SPF calculation in milliseconds Note, refer vendor documentation for respective valid values
max_delay integer	Maximum wait time in milliseconds for SPF calculations Note, refer vendor documentation for respective valid values
receive_delay integer	Delay between receiving a change to SPF calculation in milliseconds Note, refer vendor documentation for respective valid values
running_config string	This option is used only with state parsed. The value of this option should be the output received from the IOS device by executing the command sh running-config \| section ^router ospfv3. The state parsed reads the configuration from `running_config` option and transforms it into Ansible structured data as per the resource module’s argspec and the value is then returned in the parsed key within the result.
state string	The state the configuration should be left in The states rendered, gathered and parsed does not perform any change on the device. The state rendered will transform the configuration in `config` option to platform specific CLI commands which will be returned in the rendered key within the result. For state rendered active connection to remote host is not required. The state gathered will fetch the running configuration from device and transform it into structured data in the format as per the resource module argspec and the value is returned in the gathered key within the result. The state parsed reads the configuration from `running_config` option and transforms it into JSON format as per the resource module parameters and the value is returned in the parsed key within the result. The value of `running_config` option should be the same format as the output of command show running-config \| include ip route\|ipv6 route executed on device. For state parsed active connection to remote host is not required. Choices: `"merged"` ← (default) `"replaced"` `"overridden"` `"deleted"` `"gathered"` `"parsed"` `"rendered"`

Notes 

Note

Tested against Cisco IOSXE Version 17.3 on CML.
This module works with connection network_cli. See https://docs.ansible.com/ansible/latest/network/user_guide/platform_ios.html

Examples 

# Using merged

# Before state:
# -------------
#
# router-ios#sh running-config | section ^router ospfv3
# router-ios#

- name: Merge provided OSPFV3 configuration
  cisco.ios.ios_ospfv3:
    config:
      processes:
        - process_id: 1
          max_metric:
            router_lsa: true
            on_startup:
              time: 110
          address_family:
            - afi: ipv4
              unicast: true
              vrf: blue
              adjacency:
                min_adjacency: 50
                max_adjacency: 50
              areas:
                - area_id: 25
                  nssa:
                    default_information_originate:
                      metric: 25
                      nssa_only: true
          areas:
            - area_id: "10"
              nssa:
                default_information_originate:
                  metric: 10
          timers:
            throttle:
              lsa:
                first_delay: 12
                min_delay: 14
                max_delay: 16
        - process_id: 200
          address_family:
            - afi: ipv4
              unicast: true
              adjacency:
                min_adjacency: 200
                max_adjacency: 200
          max_metric:
            router_lsa: true
            on_startup:
              time: 100
          auto_cost:
            reference_bandwidth: 4
    state: merged

# Task Output:
# ------------

# before: {}
#
# commands:
# - router ospfv3 1
# - max-metric router-lsa on-startup 110
# - area 10 nssa default-information-originate metric 10
# - address-family ipv4 unicast vrf blue
# - adjacency stagger 50 50
# - area 25 nssa default-information-originate metric 25 nssa-only
# - exit-address-family
# - router ospfv3 200
# - auto-cost reference-bandwidth 4
# - max-metric router-lsa on-startup 100
# - address-family ipv4 unicast
# - adjacency stagger 200 200
# - exit-address-family
#
# after:
#     processes:
#     - address_family:
#       - adjacency:
#           max_adjacency: 50
#           min_adjacency: 50
#         afi: ipv4
#         areas:
#         - area_id: '25'
#           nssa:
#             default_information_originate:
#               metric: 25
#               nssa_only: true
#         unicast: true
#         vrf: blue
#       areas:
#       - area_id: '10'
#         nssa:
#           default_information_originate:
#             metric: 10
#       max_metric:
#         on_startup:
#           time: 110
#         router_lsa: true
#       process_id: 1
#     - address_family:
#       - adjacency:
#           max_adjacency: 200
#           min_adjacency: 200
#         afi: ipv4
#         unicast: true
#       auto_cost:
#         reference_bandwidth: 4
#       max_metric:
#         on_startup:
#           time: 100
#         router_lsa: true
#       process_id: 200

# After state:
# -------------
#
# router-ios#sh running-config | section ^router ospfv3
# router ospfv3 1
#  max-metric router-lsa on-startup 110
#  area 10 nssa default-information-originate metric 10
#  !
#  address-family ipv4 unicast vrf blue
#   adjacency stagger 50 50
#   area 25 nssa default-information-originate metric 25 nssa-only
#  exit-address-family
# router ospfv3 200
#  max-metric router-lsa on-startup 100
#  auto-cost reference-bandwidth 4
#  !
#  address-family ipv4 unicast
#   adjacency stagger 200 200
#  exit-address-family

# Using deleted

# Before state:
# -------------
#
# router-ios#sh running-config | section ^router ospfv3
# router ospfv3 1
#  max-metric router-lsa on-startup 110
#  area 10 nssa default-information-originate metric 10
#  !
#  address-family ipv4 unicast vrf blue
#   adjacency stagger 50 50
#   area 25 nssa default-information-originate metric 25 nssa-only
#  exit-address-family
# router ospfv3 200
#  max-metric router-lsa on-startup 100
#  auto-cost reference-bandwidth 4
#  !
#  address-family ipv4 unicast
#   adjacency stagger 200 200
#  exit-address-family

- name: Delete provided OSPF V3 processes
  cisco.ios.ios_ospfv3:
    config:
      processes:
        - process_id: 1
    state: deleted

# Task Output:
# ------------

# before:
#     processes:
#     - address_family:
#       - adjacency:
#           max_adjacency: 50
#           min_adjacency: 50
#         afi: ipv4
#         areas:
#         - area_id: '25'
#           nssa:
#             default_information_originate:
#               metric: 25
#               nssa_only: true
#         unicast: true
#         vrf: blue
#       areas:
#       - area_id: '10'
#         nssa:
#           default_information_originate:
#             metric: 10
#       max_metric:
#         on_startup:
#           time: 110
#         router_lsa: true
#       process_id: 1
#     - address_family:
#       - adjacency:
#           max_adjacency: 200
#           min_adjacency: 200
#         afi: ipv4
#         unicast: true
#       auto_cost:
#         reference_bandwidth: 4
#       max_metric:
#         on_startup:
#           time: 100
#         router_lsa: true
#       process_id: 200
#
# commands:
# - no router ospfv3 1
#
# parsed:
#     processes:
#     - address_family:
#       - adjacency:
#           max_adjacency: 200
#           min_adjacency: 200
#         afi: ipv4
#         unicast: true
#       auto_cost:
#         reference_bandwidth: 4
#       max_metric:
#         on_startup:
#           time: 100
#         router_lsa: true
#       process_id: 200
#
# After state:
# ------------
# router-ios#sh running-config | section ^router ospfv3
# router ospfv3 200
#  max-metric router-lsa on-startup 100
#  auto-cost reference-bandwidth 4
#  !
#  address-family ipv4 unicast
#   adjacency stagger 200 200
#  exit-address-family

# Using deleted without any config passed (NOTE: This will delete all OSPFV3 configuration from device)

# Before state:
# -------------
#
# router-ios#sh running-config | section ^router ospfv3
# router ospfv3 1
#  max-metric router-lsa on-startup 110
#  area 10 nssa default-information-originate metric 10
#  !
#  address-family ipv4 unicast vrf blue
#   adjacency stagger 50 50
#   area 25 nssa default-information-originate metric 25 nssa-only
#  exit-address-family
# router ospfv3 200
#  max-metric router-lsa on-startup 100
#  auto-cost reference-bandwidth 4
#  !
#  address-family ipv4 unicast
#   adjacency stagger 200 200
#  exit-address-family

- name: Delete all OSPF processes
  cisco.ios.ios_ospfv3:
    state: deleted

# Task Output:
# ------------

# before:
#     processes:
#     - address_family:
#       - adjacency:
#           max_adjacency: 50
#           min_adjacency: 50
#         afi: ipv4
#         areas:
#         - area_id: '25'
#           nssa:
#             default_information_originate:
#               metric: 25
#               nssa_only: true
#         unicast: true
#         vrf: blue
#       areas:
#       - area_id: '10'
#         nssa:
#           default_information_originate:
#             metric: 10
#       max_metric:
#         on_startup:
#           time: 110
#         router_lsa: true
#       process_id: 1
#     - address_family:
#       - adjacency:
#           max_adjacency: 200
#           min_adjacency: 200
#         afi: ipv4
#         unicast: true
#       auto_cost:
#         reference_bandwidth: 4
#       max_metric:
#         on_startup:
#           time: 100
#         router_lsa: true
#       process_id: 200
#
# commands:
# - no router ospfv3 200
# - no router ospfv3 1
#
# after: {}
#
# After state:
# ------------
# router-ios#sh running-config | section ^router ospfv3
# router-ios#


# Using overridden

# Before state:
# -------------
#
# router ospfv3 1
#  max-metric router-lsa on-startup 110
#  area 10 nssa default-information-originate metric 10
#  !
#  address-family ipv4 unicast vrf blue
#   adjacency stagger 50 50
#   area 25 nssa default-information-originate metric 25 nssa-only
#  exit-address-family
# router ospfv3 200
#  max-metric router-lsa on-startup 100
#  auto-cost reference-bandwidth 4
#  !
#  address-family ipv4 unicast
#   adjacency stagger 200 200
#  exit-address-family

- name: Override provided OSPFV3 configuration
  cisco.ios.ios_ospfv3:
    config:
      processes:
        - process_id: 200
          max_metric:
            router_lsa: true
            on_startup:
              time: 200
          address_family:
            - afi: ipv4
              unicast: true
              adjacency:
                min_adjacency: 50
                max_adjacency: 50
              areas:
                - area_id: 200
                  nssa:
                    default_information_originate:
                      metric: 200
                      nssa_only: true
          areas:
            - area_id: "10"
              nssa:
                default_information_originate:
                  metric: 10
    state: overridden

# Task Output:
# ------------

# before:
#     processes:
#     - address_family:
#       - adjacency:
#           max_adjacency: 50
#           min_adjacency: 50
#         afi: ipv4
#         areas:
#         - area_id: '25'
#           nssa:
#             default_information_originate:
#               metric: 25
#               nssa_only: true
#         unicast: true
#         vrf: blue
#       areas:
#       - area_id: '10'
#         nssa:
#           default_information_originate:
#             metric: 10
#       max_metric:
#         on_startup:
#           time: 110
#         router_lsa: true
#       process_id: 1
#     - address_family:
#       - adjacency:
#           max_adjacency: 200
#           min_adjacency: 200
#         afi: ipv4
#         unicast: true
#       auto_cost:
#         reference_bandwidth: 4
#       max_metric:
#         on_startup:
#           time: 100
#         router_lsa: true
#       process_id: 200
#
# commands:
# - no router ospfv3 1
# - router ospfv3 200
# - no auto-cost reference-bandwidth 4
# - max-metric router-lsa on-startup 200
# - area 10 nssa default-information-originate metric 10
# - address-family ipv4 unicast
# - adjacency stagger 50 50
# - area 200 nssa default-information-originate metric 200 nssa-only
# - exit-address-family
#
# after:
#     processes:
#     - address_family:
#       - adjacency:
#           max_adjacency: 50
#           min_adjacency: 50
#         afi: ipv4
#         areas:
#         - area_id: '200'
#           nssa:
#             default_information_originate:
#               metric: 200
#               nssa_only: true
#         unicast: true
#       areas:
#       - area_id: '10'
#         nssa:
#           default_information_originate:
#             metric: 10
#       max_metric:
#         on_startup:
#           time: 200
#         router_lsa: true
#       process_id: 200

# After state:
# ------------
#
# router-ios#sh running-config | section ^router ospfv3
# router ospfv3 200
#  max-metric router-lsa on-startup 200
#  area 10 nssa default-information-originate metric 10
#  !
#  address-family ipv4 unicast
#   adjacency stagger 50 50
#   area 200 nssa default-information-originate metric 200 nssa-only
#  exit-address-family

# Using replaced

# Before state:
# -------------
#
# router-ios#sh running-config | section ^router ospfv3
# router ospfv3 1
#  max-metric router-lsa on-startup 110
#  area 10 nssa default-information-originate metric 10
#  !
#  address-family ipv4 unicast vrf blue
#   adjacency stagger 50 50
#   area 25 nssa default-information-originate metric 25 nssa-only
#  exit-address-family
# router ospfv3 200
#  max-metric router-lsa on-startup 100
#  auto-cost reference-bandwidth 4
#  !
#  address-family ipv4 unicast
#   adjacency stagger 200 200
#  exit-address-family

- name: Perform replace with provided configurations.
  cisco.ios.ios_ospfv3:
    config:
      processes:
        - process_id: 200
          max_metric:
            router_lsa: true
            on_startup:
              time: 200
          address_family:
            - afi: ipv4
              unicast: true
              adjacency:
                min_adjacency: 50
                max_adjacency: 50
              areas:
                - area_id: 200
                  nssa:
                    default_information_originate:
                      metric: 200
                      nssa_only: true
          areas:
            - area_id: "10"
              nssa:
                default_information_originate:
                  metric: 10
    state: replaced

# Task Output:
# ------------

# before:
#     processes:
#     - address_family:
#       - adjacency:
#           max_adjacency: 50
#           min_adjacency: 50
#         afi: ipv4
#         areas:
#         - area_id: '25'
#           nssa:
#             default_information_originate:
#               metric: 25
#               nssa_only: true
#         unicast: true
#         vrf: blue
#       areas:
#       - area_id: '10'
#         nssa:
#           default_information_originate:
#             metric: 10
#       max_metric:
#         on_startup:
#           time: 110
#         router_lsa: true
#       process_id: 1
#     - address_family:
#       - adjacency:
#           max_adjacency: 200
#           min_adjacency: 200
#         afi: ipv4
#         unicast: true
#       auto_cost:
#         reference_bandwidth: 4
#       max_metric:
#         on_startup:
#           time: 100
#         router_lsa: true
#       process_id: 200
#
# commands:
# - router ospfv3 200
# - no auto-cost reference-bandwidth 4
# - max-metric router-lsa on-startup 200
# - area 10 nssa default-information-originate metric 10
# - address-family ipv4 unicast
# - adjacency stagger 50 50
# - area 200 nssa default-information-originate metric 200 nssa-only
# - exit-address-family
#
# after:
#     processes:
#     - address_family:
#       - adjacency:
#           max_adjacency: 50
#           min_adjacency: 50
#         afi: ipv4
#         areas:
#         - area_id: '25'
#           nssa:
#             default_information_originate:
#               metric: 25
#               nssa_only: true
#         unicast: true
#         vrf: blue
#       areas:
#       - area_id: '10'
#         nssa:
#           default_information_originate:
#             metric: 10
#       max_metric:
#         on_startup:
#           time: 110
#         router_lsa: true
#       process_id: 1
#     - address_family:
#       - afi: ipv4
#         areas:
#         - area_id: '200'
#           nssa:
#             default_information_originate:
#               metric: 200
#               nssa_only: true
#         unicast: true
#       areas:
#       - area_id: '10'
#         nssa:
#           default_information_originate:
#             metric: 10
#       max_metric:
#         on_startup:
#           time: 200
#         router_lsa: true
#       process_id: 200
#
# After state:
# -------------
# router-ios#sh running-config | section ^router ospfv3
# router ospfv3 1
#  max-metric router-lsa on-startup 110
#  area 10 nssa default-information-originate metric 10
#  !
#  address-family ipv4 unicast vrf blue
#   adjacency stagger 50 50
#   area 25 nssa default-information-originate metric 25 nssa-only
#  exit-address-family
# router ospfv3 200
#  max-metric router-lsa on-startup 200
#  area 10 nssa default-information-originate metric 10
#  !
#  address-family ipv4 unicast
#   adjacency stagger 50 50
#   area 200 nssa default-information-originate metric 200 nssa-only
#  exit-address-family

# Using Gathered

# Before state:
# -------------
#
# router-ios#sh running-config | section ^router ospfv3
# router ospfv3 1
#  max-metric router-lsa on-startup 110
#  area 10 nssa default-information-originate metric 10
#  !
#  address-family ipv4 unicast vrf blue
#   adjacency stagger 50 50
#   area 25 nssa default-information-originate metric 25 nssa-only
#  exit-address-family
# router ospfv3 200
#  max-metric router-lsa on-startup 100
#  auto-cost reference-bandwidth 4
#  !
#  address-family ipv4 unicast
#   adjacency stagger 200 200
#  exit-address-family

- name: Gather OSPFV3 provided configurations
  cisco.ios.ios_ospfv3:
    config:
    state: gathered

# Task Output:
# ------------
#
# parsed:
#     processes:
#     - address_family:
#       - adjacency:
#           max_adjacency: 50
#           min_adjacency: 50
#         afi: ipv4
#         areas:
#         - area_id: '25'
#           nssa:
#             default_information_originate:
#               metric: 25
#               nssa_only: true
#         unicast: true
#         vrf: blue
#       areas:
#       - area_id: '10'
#         nssa:
#           default_information_originate:
#             metric: 10
#       max_metric:
#         on_startup:
#           time: 110
#         router_lsa: true
#       process_id: 1
#     - address_family:
#       - adjacency:
#           max_adjacency: 200
#           min_adjacency: 200
#         afi: ipv4
#         unicast: true
#       auto_cost:
#         reference_bandwidth: 4
#       max_metric:
#         on_startup:
#           time: 100
#         router_lsa: true
#       process_id: 200

# After state:
# ------------
#
# router-ios#sh running-config | section ^router ospfv3
# router ospfv3 1
#  max-metric router-lsa on-startup 110
#  area 10 nssa default-information-originate metric 10
#  !
#  address-family ipv4 unicast vrf blue
#   adjacency stagger 50 50
#   area 25 nssa default-information-originate metric 25 nssa-only
#  exit-address-family
# router ospfv3 200
#  max-metric router-lsa on-startup 100
#  auto-cost reference-bandwidth 4
#  !
#  address-family ipv4 unicast
#   adjacency stagger 200 200
#  exit-address-family

# Using Rendered

- name: Render the commands for provided  configuration
  cisco.ios.ios_ospfv3:
    config:
      processes:
        - process_id: 1
          max_metric:
            router_lsa: true
            on_startup:
              time: 110
          address_family:
            - afi: ipv4
              unicast: true
              vrf: blue
              adjacency:
                min_adjacency: 50
                max_adjacency: 50
              areas:
                - area_id: 25
                  nssa:
                    default_information_originate:
                      metric: 25
                      nssa_only: true
          areas:
            - area_id: "10"
              nssa:
                default_information_originate:
                  metric: 10
          timers:
            throttle:
              lsa:
                first_delay: 12
                min_delay: 14
                max_delay: 16
        - process_id: 200
          address_family:
            - afi: ipv4
              unicast: true
              adjacency:
                min_adjacency: 200
                max_adjacency: 200
          max_metric:
            router_lsa: true
            on_startup:
              time: 100
          auto_cost:
            reference_bandwidth: 4
    state: rendered

# Task Output:
# ------------

# rendered:
# - router ospfv3 1
# - max-metric router-lsa on-startup 110
# - area 10 nssa default-information-originate metric 10
# - address-family ipv4 unicast vrf blue
# - adjacency stagger 50 50
# - area 25 nssa default-information-originate metric 25 nssa-only
# - exit-address-family
# - router ospfv3 200
# - auto-cost reference-bandwidth 4
# - max-metric router-lsa on-startup 100
# - address-family ipv4 unicast
# - adjacency stagger 200 200
# - exit-address-family


# Using Parsed

# File: parsed.cfg
# ----------------
#
# router ospfv3 1
#  max-metric router-lsa on-startup 110
#  area 10 nssa default-information-originate metric 10
#  !
#  address-family ipv4 unicast vrf blue
#   adjacency stagger 50 50
#   area 25 nssa default-information-originate metric 25 nssa-only
#  exit-address-family
# router ospfv3 200
#  max-metric router-lsa on-startup 100
#  auto-cost reference-bandwidth 4
#  !
#  address-family ipv4 unicast
#   adjacency stagger 200 200
#  exit-address-family

- name: Parse the provided configuration and display structured ospfv3 facts.
  cisco.ios.ios_ospfv3:
    running_config: "{{ lookup('file', 'parsed.cfg') }}"
    state: parsed

# Task Output:
# ------------
#
# parsed:
#     processes:
#     - address_family:
#       - adjacency:
#           max_adjacency: 50
#           min_adjacency: 50
#         afi: ipv4
#         areas:
#         - area_id: '25'
#           nssa:
#             default_information_originate:
#               metric: 25
#               nssa_only: true
#         unicast: true
#         vrf: blue
#       areas:
#       - area_id: '10'
#         nssa:
#           default_information_originate:
#             metric: 10
#       max_metric:
#         on_startup:
#           time: 110
#         router_lsa: true
#       process_id: 1
#     - address_family:
#       - adjacency:
#           max_adjacency: 200
#           min_adjacency: 200
#         afi: ipv4
#         unicast: true
#       auto_cost:
#         reference_bandwidth: 4
#       max_metric:
#         on_startup:
#           time: 100
#         router_lsa: true
#       process_id: 200

Return Values 

Common return values are documented here, the following are the fields unique to this module:

Key	Description
after dictionary	The resulting configuration model invocation. Returned: when changed Sample: `"The configuration returned will always be in the same format\n of the parameters above.\n"`
before dictionary	The configuration prior to the model invocation. Returned: always Sample: `"The configuration returned will always be in the same format\n of the parameters above.\n"`
commands list / elements=string	The set of commands pushed to the remote device. Returned: always Sample: `["router ospfv3 1", "address-family ipv4 unicast vrf blue", "adjacency stagger 50 50"]`
gathered dictionary	Facts about the network resource gathered from the remote device as structured data. Returned: when state is `gathered` Sample: `"This output will always be in the same format as the module argspec.\n"`
parsed dictionary	The device native config provided in running_config option parsed into structured data as per module argspec. Returned: when state is `parsed` Sample: `"This output will always be in the same format as the module argspec.\n"`
rendered list / elements=string	The provided configuration in the task rendered in device-native format (offline). Returned: when state is `rendered` Sample: `["router ospfv3 1", "max-metric router-lsa on-startup 110", "area 10 nssa default-information-originate metric 10"]`

Authors

Sumit Jaiswal (@justjais)

cisco.ios.ios_ospfv3 module – Resource module to configure OSPFv3.

Synopsis

Parameters

Notes

Examples

Return Values