cisco.iosxr.iosxr_l2_interfaces module – Resource Module to configure L2 interfaces.
Note
This module is part of the cisco.iosxr collection (version 10.2.2).
You might already have this collection installed if you are using the ansible package.
It is not included in ansible-core.
To check whether it is installed, run ansible-galaxy collection list.
To install it, use: ansible-galaxy collection install cisco.iosxr.
To use it in a playbook, specify: cisco.iosxr.iosxr_l2_interfaces.
New in cisco.iosxr 1.0.0
Synopsis
This module manages the Layer-2 interface attributes on Cisco IOS-XR devices.
Parameters
Parameter |
Comments |
|---|---|
A dictionary of Layer-2 interface options |
|
Specify which packets will be matched by this sub-interface. |
|
IEEE 802.1Q VLAN-tagged packets. |
|
IEEE 802.1Q VLAN-tagged packets. |
|
Configures Layer 2 protocol tunneling and protocol data unit (PDU) filtering on an interface. |
|
Cisco Discovery Protocol (CDP) tunneling and data unit parameters. Choices:
|
|
CDP, PVST+, STP, and VTP protocols. Choices:
|
|
Configures the per-VLAN Spanning Tree Protocol (PVST) tunneling and data unit parameters. Choices:
|
|
Spanning Tree Protocol (STP) tunneling and data unit parameters. Choices:
|
|
VLAN Trunk Protocol (VTP) tunneling and data unit parameters. Choices:
|
|
Switchport mode access command to configure the interface as a layer 2 access Choices:
|
|
Full name of the interface/sub-interface excluding any logical unit number, e.g. GigabitEthernet0/0/0/1 or GigabitEthernet0/0/0/1.100. |
|
Configure a native VLAN ID for the trunk |
|
Propagate Layer 2 transport events. Note that it will work only when the l2tranport option is set to TRUE Choices:
|
|
802.1Q VLAN configuration. Note that it can accept either 2 VLAN IDs when configuring Q-in-Q VLAN, or it will accept 1 VLAN ID and ‘any’ as input list when configuring Q-in-any vlan as input. Note, that this option is valid only with respect to Sub-Interface and is not valid when configuring for Interface. This option is DEPRECATED and replaced with qvlan, this attribute will be removed after 2026-06-01. |
|
802.1Q VLAN configuration. Note that it can accept either 2 VLAN IDs when configuring Q-in-Q VLAN, or it will accept 1 VLAN ID and ‘any’ as input list when configuring Q-in-any vlan as input. Note, that this option is valid only with respect to Sub-Interface and is not valid when configuring for Interface. |
|
This option is used only with state parsed. The value of this option should be the output received from the IOS-XR device by executing the command show running-config interface. The state parsed reads the configuration from |
|
The state of the configuration after module completion Choices:
|
Notes
Note
This module works with connection
network_cli. See the IOS-XR Platform Options.
Examples
# Using merged
#
# Before state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
# description Ansible Network
# vrf custB
# ipv4 address 10.10.0.2 255.255.255.0
# duplex half
# shutdown
# !
# interface GigabitEthernet0/0/0/4
# description Test description
# !
- name: Merge provided configuration with device configuration
cisco.iosxr.iosxr_l2_interfaces:
config:
- name: GigabitEthernet0/0/0/3
native_vlan: 20
- name: GigabitEthernet0/0/0/4
native_vlan: 40
l2transport: true
l2protocol:
- stp: tunnel
- name: GigabitEthernet0/0/0/3.900
l2transport: true
q_vlan:
- 20
- 40
state: merged
# After state:
# ------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
# description Ansible Network
# vrf custB
# ipv4 address 10.10.0.2 255.255.255.0
# duplex half
# shutdown
# dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
# description Test description
# dot1q native vlan 10
# l2transport
# l2protocol stp tunnel
# !
# !
# interface GigabitEthernet0/0/0/3.900 l2transport
# dot1q vlan 20 40
# !
# Using replaced
#
# Before state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
# description Ansible Network
# vrf custB
# ipv4 address 10.10.0.2 255.255.255.0
# duplex half
# shutdown
# dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
# description Test description
# dot1q native vlan 10
# l2transport
# l2protocol stp tunnel
# !
# !
# interface GigabitEthernet0/0/0/3.900 l2transport
# dot1q vlan 20 40
# !
- name: >-
Replaces device configuration of listed interfaces with provided
configuration
cisco.iosxr.iosxr_l2_interfaces:
config:
- name: GigabitEthernet0/0/0/4
native_vlan: 40
l2transport: true
l2protocol:
- stp: forward
- name: GigabitEthernet0/0/0/3.900
q_vlan:
- 20
- any
state: replaced
# After state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
# description Ansible Network
# vrf custB
# ipv4 address 10.10.0.2 255.255.255.0
# duplex half
# shutdown
# dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
# description Test description
# dot1q native vlan 40
# l2transport
# l2protocol stp forward
# !
# !
# interface GigabitEthernet0/0/0/3.900 l2transport
# dot1q vlan 20 any
# !
# Using overridden
#
# Before state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
# description Ansible Network
# vrf custB
# ipv4 address 10.10.0.2 255.255.255.0
# duplex half
# shutdown
# dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
# description Test description
# dot1q native vlan 10
# l2transport
# l2protocol stp tunnel
# !
# !
# interface GigabitEthernet0/0/0/3.900 l2transport
# dot1q vlan 20 40
# !
- name: Override device configuration of all interfaces with provided configuration
cisco.iosxr.iosxr_l2_interfaces:
config:
- name: GigabitEthernet0/0/0/4
native_vlan: 40
l2transport: true
l2protocol:
- stp: forward
- name: GigabitEthernet0/0/0/3.900
q_vlan:
- 20
- any
state: overridden
# After state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
# description Ansible Network
# vrf custB
# ipv4 address 10.10.0.2 255.255.255.0
# duplex half
# shutdown
# !
# interface GigabitEthernet0/0/0/4
# description Test description
# dot1q native vlan 40
# l2transport
# l2protocol stp forward
# !
# !
# interface GigabitEthernet0/0/0/3.900
# dot1q vlan 20 any
# !
# Using deleted
#
# Before state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
# description Ansible Network
# vrf custB
# ipv4 address 10.10.0.2 255.255.255.0
# duplex half
# shutdown
# dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
# description Test description
# dot1q native vlan 10
# l2transport
# l2protocol stp tunnel
# !
# !
#
- name: "Delete L2 attributes of given interfaces (Note: This won't delete the interface itself)"
cisco.iosxr.iosxr_l2_interfaces:
config:
- name: GigabitEthernet0/0/0/4
state: deleted
# After state:
# ------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
# description Ansible Network
# vrf custB
# ipv4 address 10.10.0.2 255.255.255.0
# duplex half
# shutdown
# dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
# description Test description
# !
# Using Deleted without any config passed
# "(NOTE: This will delete all of configured resource module attributes from each configured interface)"
#
# Before state:
# -------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
# description Ansible Network
# vrf custB
# ipv4 address 10.10.0.2 255.255.255.0
# duplex half
# shutdown
# dot1q native vlan 20
# !
# interface GigabitEthernet0/0/0/4
# description Test description
# dot1q native vlan 10
# l2transport
# l2protocol stp tunnel
# !
# !
- name: "Delete L2 attributes of all interfaces (Note: This won't delete the interface itself)"
cisco.iosxr.iosxr_l2_interfaces:
state: deleted
# After state:
# ------------
#
# viosxr#show running-config interface
# interface GigabitEthernet0/0/0/3
# description Ansible Network
# vrf custB
# ipv4 address 10.10.0.2 255.255.255.0
# duplex half
# shutdown
# !
# interface GigabitEthernet0/0/0/4
# description Test description
# !
# Using parsed
# parsed.cfg
# ------------
#
# interface Loopback888
# description test for ansible
# shutdown
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 10.8.38.70 255.255.255.0
# !
# interface GigabitEthernet0/0/0/0
# description Configured and Merged by Ansible-Network
# mtu 110
# ipv4 address 172.31.1.1 255.255.255.0
# duplex half
# !
# interface GigabitEthernet0/0/0/1
# dot1q native vlan 10
# l2transport
# l2protocol cdp forward
# l2protocol pvst tunnel
# propagate remote-status
# !
# !
# interface GigabitEthernet0/0/0/3
# shutdown
# !
# interface GigabitEthernet0/0/0/3.900
# encapsulation dot1q 20 second-dot1q 40
# !
# interface GigabitEthernet0/0/0/4
# shutdown
# dot1q native vlan 40
# !
- name: Convert L2 interfaces config to argspec without connecting to the appliance
cisco.iosxr.iosxr_l2_interfaces:
running_config: "{{ lookup('file', './parsed.cfg') }}"
state: parsed
# Task Output (redacted)
# -----------------------
# "parsed": [
# {
# "name": "GigabitEthernet0/0/0/0"
# },
# {
# "l2protocol": [
# {
# "cdp": "forward"
# },
# {
# "pvst": "tunnel"
# }
# ],
# "l2transport": true,
# "name": "GigabitEthernet0/0/0/1",
# "native_vlan": 10,
# "propagate": true
# },
# {
# "name": "GigabitEthernet0/0/0/3"
# },
# {
# "name": "GigabitEthernet0/0/0/3.900",
# "q_vlan": [
# 20,
# 40
# ]
# },
# {
# "name": "GigabitEthernet0/0/0/4",
# "native_vlan": 40
# }
# ]
# Using rendered
- name: Render platform specific commands from task input using rendered state
cisco.iosxr.iosxr_l2_interfaces:
config:
- name: GigabitEthernet0/0/0/1
native_vlan: 10
l2transport: true
l2protocol:
- pvst: tunnel
- cdp: forward
propagate: true
- name: GigabitEthernet0/0/0/3.900
q_vlan:
- 20
- 40
- name: GigabitEthernet0/0/0/4
native_vlan: 40
state: rendered
# Task Output (redacted)
# -----------------------
# "rendered": [
# "interface GigabitEthernet0/0/0/1",
# "dot1q native vlan 10",
# "l2transport l2protocol pvst tunnel",
# "l2transport l2protocol cdp forward",
# "l2transport propagate remote-status",
# "interface GigabitEthernet0/0/0/3.900",
# "dot1q vlan 20 40",
# "interface GigabitEthernet0/0/0/4",
# "dot1q native vlan 40"
# ]
# Using gathered
# Before state:
# ------------
#
# RP/0/0/CPU0:an-iosxr-02#show running-config interface
# interface Loopback888
# description test for ansible
# shutdown
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 10.8.38.70 255.255.255.0
# !
# interface GigabitEthernet0/0/0/0
# description Configured and Merged by Ansible-Network
# mtu 110
# ipv4 address 172.31.1.1 255.255.255.0
# duplex half
# !
# interface GigabitEthernet0/0/0/1
# dot1q native vlan 10
# l2transport
# l2protocol cdp forward
# l2protocol pvst tunnel
# propagate remote-status
# !
# !
# interface GigabitEthernet0/0/0/3
# shutdown
# !
# interface GigabitEthernet0/0/0/3.900
# encapsulation dot1q 20 second-dot1q 40
# !
# interface GigabitEthernet0/0/0/4
# shutdown
# dot1q native vlan 40
# !
- name: Gather IOSXR l2 interfaces as in given arguments
cisco.iosxr.iosxr_l2_interfaces:
config:
state: gathered
# Task Output (redacted)
# -----------------------
#
# "gathered": [
# {
# "name": "GigabitEthernet0/0/0/0"
# },
# {
# "l2protocol": [
# {
# "cdp": "forward"
# },
# {
# "pvst": "tunnel"
# }
# ],
# "l2transport": true,
# "name": "GigabitEthernet0/0/0/1",
# "native_vlan": 10,
# "propagate": true
# },
# {
# "name": "GigabitEthernet0/0/0/3"
# },
# {
# "name": "GigabitEthernet0/0/0/3.900",
# "q_vlan": [
# 20,
# 40
# ]
# },
# {
# "name": "GigabitEthernet0/0/0/4",
# "native_vlan": 40
# }
# ]
# After state:
# ------------
#
# RP/0/0/CPU0:an-iosxr-02#show running-config interface
# interface Loopback888
# description test for ansible
# shutdown
# !
# interface MgmtEth0/0/CPU0/0
# ipv4 address 10.8.38.70 255.255.255.0
# !
# interface GigabitEthernet0/0/0/0
# description Configured and Merged by Ansible-Network
# mtu 110
# ipv4 address 172.31.1.1 255.255.255.0
# duplex half
# !
# interface GigabitEthernet0/0/0/1
# dot1q native vlan 10
# l2transport
# l2protocol cdp forward
# l2protocol pvst tunnel
# propagate remote-status
# !
# !
# interface GigabitEthernet0/0/0/3
# shutdown
# !
# interface GigabitEthernet0/0/0/3.900
# encapsulation dot1q 20 second-dot1q 40
# !
# interface GigabitEthernet0/0/0/4
# shutdown
# dot1q native vlan 40
# !
Return Values
Common return values are documented here, the following are the fields unique to this module:
Key |
Description |
|---|---|
The configuration as structured data after module completion. Returned: when changed Sample: |
|
The configuration as structured data prior to module invocation. Returned: always Sample: |
|
The set of commands pushed to the remote device Returned: always Sample: |