cisco.iosxr.iosxr_ospfv2 module – Resource module to configure OSPFv2.

Note

This module is part of the cisco.iosxr collection (version 10.2.2).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install cisco.iosxr.

To use it in a playbook, specify: cisco.iosxr.iosxr_ospfv2.

New in cisco.iosxr 1.0.0

Synopsis

• This module manages global OSPFv2 configuration on devices running Cisco IOS-XR

Parameters

Parameter	Comments
config dictionary	A list of OSPFv2 process configuration
processes list / elements=dictionary	A list of OSPFv2 instances configuration
address_family_unicast boolean	Enable unicast topology for ipv4 address family Choices: false true
adjacency_stagger dictionary	Stagger OSPFv2 adjacency bring up
disable boolean	Disable stagger OSPFv2 adjacency Choices: false true
max_adjacency integer	Maximum simultaneous neighbors to bring up
min_adjacency integer	Initial number of neighbors to bring up per area (default 2)
apply_weight dictionary	Enable weights configured under interfaces for load sharing
bandwidth integer	Reference bandwidth to use for calculation (Mbits/sec)
default_weight integer	Specify default weight value to use when it is not configured under interface
areas list / elements=dictionary	Configure OSPFv2 areas’ properties
area_id string / required	Area ID as IP address or integer
authentication dictionary	Enable authentication
keychain string	Specify keychain name
message_digest dictionary	Use message-digest authentication
keychain string	Specify keychain name
no_auth boolean	Use no authentication Choices: false true
authentication_key dictionary	Used to mention authentication password (key)
clear string	Specifies an UNENCRYPTED password (key) will follow
encrypted string	Specifies an ENCRYPTED password (key) will follow
password string	The OSPFv2 password (key)
bfd dictionary	Configure BFD parameters
fast_detect dictionary	Configure fast detection
set boolean	Enable fast detection only Choices: false true
strict_mode boolean	Hold down neighbor session until BFD session is up Choices: false true
minimum_interval integer	Hello interval in milli-seconds
multiplier integer	Detect multiplier
cost integer	Interface cost
dead_interval integer	Interval after which a neighbor is declared dead
default_cost integer	Set the summary default-cost of a NSSA/stub area. Stub’s advertised external route metric
hello_interval integer	Time between HELLO packets
mpls dictionary	Configure MPLS routing protocol parameters
ldp dictionary	Configure LDP parameters
auto_config boolean	Enable LDP IGP interface auto-configuration Choices: false true
sync boolean	Enable LDP IGP synchronization Choices: false true
sync_igp_shortcuts boolean	LDP sync for igp-shortcut tunnels Choices: false true
traffic_eng boolean	Configure an ospf area to run MPLS Traffic Engineering Choices: false true
mtu_ignore string	Enable/Disable ignoring of MTU in DBD packets Choices: "enable" "disable"
nssa dictionary	NSSA settings for the area
default_information_originate dictionary	Originate default Type 7 LSA
metric integer	OSPFv2 default metric
metric_type integer	Metric type for default routes
no_redistribution boolean	Do not send redistributed LSAs into NSSA area Choices: false true
no_summary boolean	Do not send summary LSAs into NSSA area Choices: false true
set boolean	Configure area as NSSA Choices: false true
translate dictionary	Translate LSA
type7 dictionary	Translate from Type 7 to Type 5
always boolean	Always translate LSAs Choices: false true
ranges list / elements=dictionary	Summarize routes matching address/mask (border routers only)
address string / required	IP in Prefix format (x.x.x.x/len)
advertise boolean	Advertise this range (default) Choices: false true
not_advertise boolean	DoNotAdvertise this range Choices: false true
route_policy list / elements=dictionary	Specify the route-policy to filter type 3 LSAs (list can have one inbound and/or one outbound policy only)
direction string	Specify inbound or outbound Choices: "in" "out"
parameters list / elements=string	Specify parameter values for the policy
stub dictionary	Settings for configuring the area as a stub
no_summary boolean	Do not send summary LSA into stub area Choices: false true
set boolean	Configure the area as a stub Choices: false true
transmit_delay integer	Estimated time needed to send link-state update packet
virtual_link list / elements=dictionary	Define a virtual link
authentication dictionary	Enable authentication
keychain string	Specify keychain name
message_digest dictionary	Use message-digest authentication
keychain string	Specify keychain name
no_auth boolean	Use no authentication Choices: false true
authentication_key dictionary	Used to mention authentication password (key)
clear string	Specifies an UNENCRYPTED password (key) will follow
encrypted string	Specifies an ENCRYPTED password (key) will follow
password string	The OSPFv2 password (key)
dead_interval integer	Interval after which a neighbor is declared dead
hello_interval integer	Time between HELLO packets
id string / required	Router-ID of virtual link neighbor (A.B.C.D)
message_digest_key dictionary	Message digest authentication password (key)
id integer / required	Key ID (1-255)
md5 dictionary	Use MD5 Algorithm
clear boolean	Specifies an UNENCRYPTED password (key) will follow Choices: false true
encrypted boolean	Specifies an ENCRYPTED password (key) will follow Choices: false true
password string	The OSPFv2 password (key)
retransmit_interval integer	Delay between LSA retransmissions
transmit_delay integer	Link state transmit delay
authentication dictionary	Enable authentication
keychain string	Specify keychain name
message_digest dictionary	Use message-digest authentication
keychain string	Specify keychain name
set boolean	Specify message-digest selection Choices: false true
no_auth boolean	Use no authentication Choices: false true
authentication_key dictionary	Used to mention authentication password (key)
clear boolean	Specifies an UNENCRYPTED password (key) will follow Choices: false true
encrypted boolean	Specifies an ENCRYPTED password (key) will follow Choices: false true
password string	The OSPFv2 password (key)
auto_cost dictionary	Calculate OSPFv2 interface cost according to bandwidth
disable boolean	Assign OSPFv2 cost based on interface type Choices: false true
reference_bandwidth integer	Specify reference bandwidth in megabits per sec
bfd dictionary	Configure BFD parameters
fast_detect dictionary	Configure fast detection
set boolean	Enable fast detection only Choices: false true
strict_mode boolean	Hold down neighbor session until BFD session is up Choices: false true
minimum_interval integer	Hello interval in milli-seconds
multiplier integer	Detect multiplier
capability dictionary	Enable specific OSPFv2 feature
opaque dictionary	Configure opaque LSA
disable boolean	Disable Opaque LSA capability Choices: false true
set boolean	Enable opaque LSA Choices: false true
type7 string	NSSA capability
cost integer	Interface cost (1-65535)
database_filter string	Filter OSPFv2 LSA during synchronization and flooding (all outgoing LSA). Enable/Disable filtering Choices: "enable" "disable"
dead_interval integer	Interval after which a neighbor is declared dead
default_information_originate dictionary	Distribute default route
always boolean	Always advertise default route Choices: false true
metric integer	OSPFv2 default metric
metric_type integer	OSPFv2 metric type for default routes
route_policy string	Apply route-policy to default-information origination
set boolean	Enable distribution of default route Choices: false true
default_metric integer	Set metric of redistributed routes
demand_circuit string	Enable/Disable OSPFv2 demand circuit Choices: "enable" "disable"
distance dictionary	Define an administrative distance
admin_distance list / elements=dictionary	Administrative distance
access_list string	Access list name
source string	Source IP address
value integer	Distance value
wildcard string	IP wild card bits (A.B.C.D)
ospf_distance dictionary	OSPFv2 administrative distance
external integer	Distance for external routes
inter_area integer	Distance for inter-area routes
intra_area integer	Distance for intra-area routes
distribute_bgp_ls dictionary	Enable Distribution of LSAs to external services
instance_id integer	Set distribution process instance identifier
throttle integer	Throttle time between successive LSA updates
distribute_link_state dictionary	Enable Distribution of LSAs to external services
instance_id integer	Set distribution process instance identifier
throttle integer	Throttle time between successive LSA updates
distribute_list list / elements=dictionary	Filter networks in routing updates (list can have one inbound and/or one outbound policy only)
access_list string	Inbound/outbound access-list
direction string	Filter incoming/outgoing routing updates Choices: "in" "out"
outgoing_params dictionary	Specify additional parameters for outgoing updates only
id string	For BGP, specify AS number. 2-byte AS number (or) 4-byte AS number in asdot (X.Y) format (or) 4-byte AS number in asplain format For OSPF, specify OSPFv2 instance name
route_type string	Type of routes Choices: "bgp" "connected" "dagr" "ospf" "static"
route_policy string	Route Policy to filter OSPFv2 prefixes (for incoming updates only)
external_out string	Enable/Disable advertisement of intra-area prefixes as external Choices: "enable" "disable"
flood_reduction string	Enable/Disable OSPFv2 Flood Reduction Choices: "enable" "disable"
hello_interval integer	Time between HELLO packets (<1-65535> seconds)
ignore_lsa_mospf boolean	Do not complain upon receiving MOSPFv2 Type 6 LSA Choices: false true
link_down_fast_detect boolean	Enable fast or early detection of link-down events Choices: false true
log_adjacency_changes dictionary	Log adjacency state changes
detail boolean	Log all state changes Choices: false true
disable boolean	Disable log adjacency changes Choices: false true
set boolean	Set log adjacency Choices: false true
loopback_stub_network string	Advertise loopback as a stub network Choices: "enable" "disable"
max_lsa dictionary	Feature to limit the number of non-self-originated LSAs
ignore_count integer	Set count on how many times adjacencies can be suppressed
ignore_time integer	Set number of minutes during which all adjacencies are suppressed
reset_time integer	Set number of minutes after which ignore-count is reset to zero
threshold integer	Threshold value (%) at which to generate a warning message
warning_only boolean	Log a warning message when limit is exceeded Choices: false true
max_metric dictionary	Set maximum metric
router_lsa dictionary	Maximum metric in self-originated router-LSAs
external_lsa dictionary	External LSA configuration
max_metric_value integer	Set max metric value for external LSAs
set boolean	Set external-lsa attribute Choices: false true
include_stub boolean	Advertise Max metric for Stub links as well Choices: false true
on_startup dictionary	Effective only at startup
set boolean	Set on-startup attribute Choices: false true
wait_for_bgp_asn integer	ASN of BGP to wait for
wait_period integer	Wait period in seconds after startup
set boolean	Set router-lsa attribute Choices: false true
summary_lsa dictionary	Summary LSAs configuration
max_metric_value integer	Max metric value for summary LSAs
set boolean	Set summary-lsa attribute Choices: false true
message_digest_key dictionary	Message digest authentication password (key)
id integer / required	Key ID
md5 dictionary / required	Use MD5 Algorithm
clear boolean	Specifies an UNENCRYPTED password (key) will follow Choices: false true
encrypted boolean	Specifies an ENCRYPTED password (key) will follow Choices: false true
password string	The OSPFv2 password (key)
microloop_avoidance dictionary	Avoid microloops
protected boolean	Avoid microloops for protected prefixes only) Choices: false true
rib_update_delay integer	Delay to introduce between SPF and RIB updates
segment_routing boolean	Enable segment routing microloop avoidance Choices: false true
monitor_convergence dictionary	Enables OSPFv2 route convergence monitoring
prefix_list string	Enables Individual Prefix Monitoring
track_external_routes boolean	Enables Tracking External(Type-5/7) Prefix monitoring Choices: false true
track_ip_frr boolean	Enables Tracking IP-Frr Convergence Choices: false true
track_summary_routes boolean	Enables Tracking Summary(Inter-Area) Prefix monitoring Choices: false true
mpls dictionary	Configure MPLS routing protocol parameters
ldp dictionary	Configure LDP parameters
auto_config boolean	Enable LDP IGP interface auto-configuration Choices: false true
sync boolean	Enable LDP IGP synchronization Choices: false true
sync_igp_shortcuts boolean	LDP sync for igp-shortcut tunnels Choices: false true
traffic_eng dictionary	Routing protocol commands for MPLS Traffic Engineering
autoroute_exclude dictionary	Exclude IP address destinations from using TE tunnels
parameters list / elements=string	Specify parameter values for the policy
route_policy string	Policy name
igp_intact boolean	Retain one or more IPv4 nexthops with tunnel nexthops Choices: false true
ldp_sync_update boolean	Enable LDP sync induced metric propagation Choices: false true
multicast_intact boolean	Publish multicast-intact paths to RIB Choices: false true
router_id string	Traffic Engineering stable IP address for system
mtu_ignore string	Enable/Disable ignoring of MTU in DBD packets Choices: "enable" "disable"
network dictionary	Network type
broadcast boolean	Specify OSPFv2 broadcast multi-access network Choices: false true
non_broadcast boolean	Specify OSPFv2 NBMA network Choices: false true
point_to_multipoint boolean	Specify OSPFv2 point-to-multipoint network Choices: false true
point_to_point boolean	Specify OSPFv2 point-to-point network Choices: false true
nsf dictionary	Non-stop forwarding
cisco dictionary	Cisco Non-stop forwarding
enforce_global boolean	Cancel NSF restart when non-NSF-aware neighbors detected for the whole OSPFv2 process Choices: false true
set boolean	Enable Cisco NSF Choices: false true
flush_delay_time integer	Maximum time allowed for external route learning
ietf dictionary	IETF graceful restart
helper_disable boolean	Disable router’s helper support level Choices: false true
set boolean	Only enable ietf option Choices: false true
interval integer	Minimum interval between NSF restarts (<90-3600> seconds)
lifetime integer	Maximum route lifetime following restart (<90-1800> seconds)
nsr boolean	Enable NSR for all VRFs in this process. ‘False’ option to disable NSR for all VRFs in this process Choices: false true
packet_size integer	Size of OSPFv2 packets to use. min=576 max=MTU bytes
passive string	Enable/Disable passive Choices: "enable" "disable"
prefix_suppression dictionary	Suppress advertisement of the prefixes
secondary_address boolean	Enable/Disable secondary address suppression Choices: false true
set boolean	Set the suppression option Choices: false true
priority integer	Router priority
process_id string / required	The OSPFv2 Process ID
protocol_shutdown dictionary	Protocol specific configuration
host_mode boolean	Only traffic destined for this box allowed(cisco-support) Choices: false true
limit dictionary	High watermark for incoming priority events
high integer	Hello events are dropped when incoming event queue exceeds this value
low integer	DBD/LS Update/Req packets are dropped when incoming event queue exceeds this value
medium integer	LSA ACKs are dropped when incoming event queue exceeds this value
on_reload boolean	Shutdown post reload only Choices: false true
set boolean	Shutdown the OSPFv2 Protocol Choices: false true
redistribute dictionary	Redistribute information from another routing Protocol
id string	OnePK application name for application routes (or) AS number for bgp and eigrp (or) instance name for isis and ospf
level integer	ISIS levels Choices: 1 2 12
lsa_type_summary boolean	LSA type 3 for redistributed routes Choices: false true
match string	Redistribution of routes. For OSPFv2 - external/internal/nssa-external 1/2. For EIGRP - external/internal
metric integer	Metric for redistributed routes
metric_type integer	OSPFv2 exterior metric type for redistributed routes Choices: 1 2
nssa_only boolean	Redistribute to NSSA areas only Choices: false true
preserve_med boolean	Preserve med of BGP routes Choices: false true
route_policy dictionary	Apply route-policy to redistribution
name string	Name of the policy
parameters list / elements=string	Specify parameter values for the policy
route_type string	Route type to redistribute Choices: "application" "bgp" "connected" "dagr" "eigrp" "isis" "mobile" "ospf" "rip" "static" "subscriber"
tag integer	Set tag for routes redistributed into OSPFv2
retransmit_interval integer	Delay between LSA retransmissions
router_id string	OSPFv2 router-id in IPv4 address format (A.B.C.D)
security_ttl dictionary	Enable security
hops integer	Maximum number of IP hops allowed <1-254>
set boolean	Enable ttl security Choices: false true
summary_in string	Enable/Disable advertisement of external prefixes as inter-area Choices: "enable" "disable"
summary_prefix list / elements=dictionary	Configure IP address summaries
not_advertise boolean	Suppress routes that match the specified prefix/mask pair Choices: false true
prefix string / required	IP summary address/mask (A.B.C.D/prefix)
tag integer	Set tag
timers dictionary	Configure timer related constants
graceful_shutdown dictionary	Timers for graceful shutdown(cisco-support)
initial_delay integer	Delay before starting graceful shutdown
retain_routes integer	Time to keep routes active after graceful shutdown
lsa dictionary	OSPFv2 global LSA timers
group_pacing integer	OSPFv2 LSA group pacing timer. Interval between group of LSA being refreshed or maxaged
min_arrival integer	OSPFv2 MinLSArrival timer. The minimum interval in millisec between accepting the same LSA
refresh integer	OSPFv2 LSA refresh interval. How often self-originated LSAs should be refreshed, in seconds
pacing_flood integer	OSPFv2 flood pacing timer. Interval in msec to pace flooding on all interfaces
throttle dictionary	OSPFv2 throttle timers
fast_reroute integer	Fast-reroute throttle timer. Delay between end of SPF and start of the fast-reroute computation in milliseconds
lsa_all dictionary	LSA throttle timers for all types of OSPFv2 LSAs
initial_delay integer	Delay to generate first occurance of LSA in milliseconds
max_delay integer	Maximum delay between originating the same LSA in milliseconds
min_delay integer	Minimum delay between originating the same LSA in milliseconds
spf dictionary	OSPFv2 SPF throttle timers
change_delay integer	Delay between receiving a change to SPF calculation in milliseconds
max_wait integer	Maximum wait time in milliseconds for SPF calculations
second_delay integer	Delay between first and second SPF calculation in milliseconds
transmit_delay integer	Estimated time needed to send link-state update packet
weight integer	Interface weight
running_config string	This option is used only with state parsed. The value of this option should be the output received from the IOS-XR device by executing the command show running-config router ospf. The state parsed reads the configuration from running_config option and transforms it into Ansible structured data as per the resource module’s argspec and the value is then returned in the parsed key within the result.
state string	The state the configuration should be left in. Choices: "merged" ← (default) "replaced" "deleted" "parsed" "gathered" "rendered" "overridden"

Notes

Note

• This module works with connection network_cli. See the IOS-XR Platform Options

Examples

# Using merged

# Before state:
# -------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 15:54:44.569 UTC
# % No such configuration item(s)
#

- name: Merge provided OSPFv2 configuration with the existing configuration
  cisco.iosxr.iosxr_ospfv2:
    config:
      processes:
        - process_id: '27'
          areas:
            - area_id: '10'
              hello_interval: 2
              authentication:
                keychain: ansi11393
        - process_id: '26'
          adjacency_stagger:
            max_adjacency: 20
            min_adjacency: 10
        - process_id: '10'
          authentication:
            keychain: ansible_test1102
          areas:
            - area_id: '11'
              default_cost: 5
              cost: 11
            - area_id: 22
              default_cost: 6
        - process_id: '30'
          areas:
            - area_id: 11
              default_cost: 5
            - area_id: 22
              default_cost: 6
          cost: 2
          default_metric: 10
          transmit_delay: 2
          hello_interval: 1
          dead_interval: 2
          retransmit_interval: 2
          weight: 2
          packet_size: 577
          priority: 1
          router_id: 2.2.2.2
          demand_circuit: enable
          passive: disable
          summary_in: enable
          flood_reduction: disable
          mtu_ignore: enable
          external_out: disable
    state: merged

# Task Output:
# ------------
#
# before: {}
#
# commands:
#   - router ospf 30
#   - cost 2
#   - weight 2
#   - passive disable
#   - priority 1
#   - flood-reduction disable
#   - default-metric 10
#   - router-id 2.2.2.2
#   - demand-circuit enable
#   - packet-size 577
#   - transmit-delay 2
#   - summary-in enable
#   - external-out disable
#   - dead-interval 2
#   - hello-interval 1
#   - retransmit-interval 2
#   - mtu-ignore enable
#   - area 11 default-cost 5
#   - area 22 default-cost 6
#   - router ospf 26
#   - adjacency stagger 10 20
#   - router ospf 10
#   - authentication keychain ansible_test1102
#   - area 11 default-cost 5
#   - area 11 cost 11
#   - area 22 default-cost 6
#   - router ospf 27
#   - area 10 authentication keychain ansi11393
#   - area 10 hello-interval 2
#
# after:
#     processes:
#     - areas:
#       - area_id: '11'
#         cost: 11
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       authentication:
#         keychain: ansible_test1102
#       process_id: '10'
#     - adjacency_stagger:
#         max_adjacency: 20
#         min_adjacency: 10
#       process_id: '26'
#     - areas:
#       - area_id: '10'
#         authentication:
#           keychain: ansi11393
#         hello_interval: 2
#       process_id: '27'
#     - areas:
#       - area_id: '11'
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       cost: 2
#       dead_interval: 2
#       default_metric: 10
#       demand_circuit: enable
#       external_out: disable
#       flood_reduction: disable
#       hello_interval: 1
#       mtu_ignore: enable
#       packet_size: 577
#       passive: disable
#       priority: 1
#       process_id: '30'
#       retransmit_interval: 2
#       router_id: 2.2.2.2
#       summary_in: enable
#       transmit_delay: 2
#       weight: 2
#
# After state:
# ------------
#
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#   authentication keychain ansi11393
#   hello-interval 2
#  !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !

# Using replaced
#
# Before state:
# -------------
#
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 16:06:44.406 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#   authentication keychain ansi11393
#   hello-interval 2
#  !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
#
- name: Replace running OSPFv2 routes configurations with provided config.
  cisco.iosxr.iosxr_ospfv2:
    config:
      processes:
        - process_id: 27
          areas:
            - area_id: 10
              hello_interval: 2
            - area_id: 20
              cost: 2
              default_cost: 2
              authentication:
                keychain: ansi11393
        - process_id: 26
          adjacency_stagger:
            min_adjacency: 10
            max_adjacency: 20
    state: replaced

# Task Output:
# ------------
#
# before:
#     processes:
#     - areas:
#       - area_id: '11'
#         cost: 11
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       authentication:
#         keychain: ansible_test1102
#       process_id: '10'
#     - adjacency_stagger:
#         max_adjacency: 20
#         min_adjacency: 10
#       process_id: '26'
#     - areas:
#       - area_id: '10'
#         authentication:
#           keychain: ansi11393
#         hello_interval: 2
#       process_id: '27'
#     - areas:
#       - area_id: '11'
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       cost: 2
#       dead_interval: 2
#       default_metric: 10
#       demand_circuit: enable
#       external_out: disable
#       flood_reduction: disable
#       hello_interval: 1
#       mtu_ignore: enable
#       packet_size: 577
#       passive: disable
#       priority: 1
#       process_id: '30'
#       retransmit_interval: 2
#       router_id: 2.2.2.2
#       summary_in: enable
#       transmit_delay: 2
#       weight: 2
#
# commands:
#   - router ospf 27
#   - no area 10 authentication keychain ansi11393
#   - area 20 authentication keychain ansi11393
#   - area 20 default-cost 2
#   - area 20 cost 2
#
# after:
#     processes:
#     - areas:
#       - area_id: '11'
#         cost: 11
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       authentication:
#         keychain: ansible_test1102
#       process_id: '10'
#     - adjacency_stagger:
#         max_adjacency: 20
#         min_adjacency: 10
#       process_id: '26'
#     - areas:
#       - area_id: '10'
#         hello_interval: 2
#       - area_id: '20'
#         authentication:
#           keychain: ansi11393
#         cost: 2
#         default_cost: 2
#       process_id: '27'
#     - areas:
#       - area_id: '11'
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       cost: 2
#       dead_interval: 2
#       default_metric: 10
#       demand_circuit: enable
#       external_out: disable
#       flood_reduction: disable
#       hello_interval: 1
#       mtu_ignore: enable
#       packet_size: 577
#       passive: disable
#       priority: 1
#       process_id: '30'
#       retransmit_interval: 2
#       router_id: 2.2.2.2
#       summary_in: enable
#       transmit_delay: 2
#       weight: 2
#
# After state:
# ------------
#
# RP/0/RP0/CPU0:anton(config)#do show running-config router ospf
# Thu Jun 11 16:40:31.038 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#   hello-interval 2
#  !
#  area 20
#   cost 2
#   authentication keychain ansi11393
#   default-cost 2
#  !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !

# Using overridden
#
# Before state:
# -------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 16:06:44.406 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#   hello-interval 2
#  !
#  area 20
#   cost 2
#   authentication keychain ansi11393
#   default-cost 2
#  !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !

- name: Override existing OSPFv2 configurations with provided config.
  cisco.iosxr.iosxr_ospfv2:
    config:
      processes:
        - process_id: 27
          areas:
            - area_id: 10
              hello_interval: 2
              authentication:
                keychain: ansi11393
            - area_id: 20
              cost: 2
              default_cost: 2
              authentication:
                keychain: ansi11393
        - process_id: 26
          adjacency_stagger:
            min_adjacency: 10
            max_adjacency: 20
    state: overridden


#
# Task Output:
# ------------
#
# before:
#     processes:
#     - areas:
#       - area_id: '11'
#         cost: 11
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       authentication:
#         keychain: ansible_test1102
#       process_id: '10'
#     - adjacency_stagger:
#         max_adjacency: 20
#         min_adjacency: 10
#       process_id: '26'
#     - areas:
#       - area_id: '10'
#         hello_interval: 2
#       - area_id: '20'
#         authentication:
#           keychain: ansi11393
#         cost: 2
#         default_cost: 2
#       process_id: '27'
#     - areas:
#       - area_id: '11'
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       cost: 2
#       dead_interval: 2
#       default_metric: 10
#       demand_circuit: enable
#       external_out: disable
#       flood_reduction: disable
#       hello_interval: 1
#       mtu_ignore: enable
#       packet_size: 577
#       passive: disable
#       priority: 1
#       process_id: '30'
#       retransmit_interval: 2
#       router_id: 2.2.2.2
#       summary_in: enable
#       transmit_delay: 2
#       weight: 2

#
# commands:
#   - router ospf 10
#   - no authentication keychain ansible_test1102
#   - no area 11 default-cost 5
#   - no area 11 cost 11
#   - no area 22 default-cost 6
#   - router ospf 30
#   - no cost 2
#   - no weight 2
#   - no passive disable
#   - no priority 1
#   - no flood-reduction disable
#   - no default-metric 10
#   - no router-id 2.2.2.2
#   - no demand-circuit enable
#   - no packet-size 577
#   - no transmit-delay 2
#   - no summary-in enable
#   - no external-out disable
#   - no dead-interval 2
#   - no hello-interval 1
#   - no retransmit-interval 2
#   - no mtu-ignore enable
#   - no area 11 default-cost 5
#   - no area 22 default-cost 6
#   - router ospf 27
#   - area 10 authentication keychain ansi11393
#
# after:
#     processes:
#     - process_id: '10'
#     - adjacency_stagger:
#         max_adjacency: 20
#         min_adjacency: 10
#       process_id: '26'
#     - areas:
#       - area_id: '10'
#         authentication:
#           keychain: ansi11393
#         hello_interval: 2
#       - area_id: '20'
#         authentication:
#           keychain: ansi11393
#         cost: 2
#         default_cost: 2
#       process_id: '27'
#     - process_id: '30'
#
# After state:
# ------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 16:50:36.332 UTC
# router ospf 10
#  area 11
#  !
#  area 22
#  !
# !
# router ospf 26
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#   authentication keychain ansi11393
#   hello-interval 2
#  !
#  area 20
#   cost 2
#   authentication keychain ansi11393
#   default-cost 2
#  !
# !
# router ospf 30
#  area 11
#  !
#  area 22
#  !
# !
#

# Using deleted
#
# Before state:
# -------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 16:06:44.406 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#   authentication keychain ansi11393
#   hello-interval 2
#  !
#  area 20
#   cost 2
#   authentication keychain ansi11393
#   default-cost 2
#  !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !

- name: Deleted provided ospfv2 processes.
  cisco.iosxr.iosxr_ospfv2:
    config:
      processes:
        - process_id: '10'
        - process_id: '26'
        - process_id: '27'
        - process_id: '30'
    state: deleted


#
# Task Output:
# ------------
#
# before:
#     processes:
#     - areas:
#       - area_id: '11'
#         cost: 11
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       authentication:
#         keychain: ansible_test1102
#       process_id: '10'
#     - adjacency_stagger:
#         max_adjacency: 20
#         min_adjacency: 10
#       process_id: '26'
#     - areas:
#       - area_id: '10'
#         authentication:
#           keychain: ansi11393
#         hello_interval: 2
#       - area_id: '20'
#         authentication:
#           keychain: ansi11393
#         cost: 2
#         default_cost: 2
#       process_id: '27'
#     - areas:
#       - area_id: '11'
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       cost: 2
#       dead_interval: 2
#       default_metric: 10
#       demand_circuit: enable
#       external_out: disable
#       flood_reduction: disable
#       hello_interval: 1
#       mtu_ignore: enable
#       packet_size: 577
#       passive: disable
#       priority: 1
#       process_id: '30'
#       retransmit_interval: 2
#       router_id: 2.2.2.2
#       summary_in: enable
#       transmit_delay: 2
#       weight: 2
#
# commands:
#   - router ospf 10
#   - no authentication keychain ansible_test1102
#   - no area 11 default-cost 5
#   - no area 11 cost 11
#   - no area 22 default-cost 6
#   - router ospf 26
#   - no adjacency stagger 10 20
#   - router ospf 27
#   - no area 10 authentication keychain ansi11393
#   - no area 10 hello-interval 2
#   - no area 20 authentication keychain ansi11393
#   - no area 20 default-cost 2
#   - no area 20 cost 2
#   - router ospf 30
#   - no cost 2
#   - no weight 2
#   - no passive disable
#   - no priority 1
#   - no flood-reduction disable
#   - no default-metric 10
#   - no router-id 2.2.2.2
#   - no demand-circuit enable
#   - no packet-size 577
#   - no transmit-delay 2
#   - no summary-in enable
#   - no external-out disable
#   - no dead-interval 2
#   - no hello-interval 1
#   - no retransmit-interval 2
#   - no mtu-ignore enable
#   - no area 11 default-cost 5
#   - no area 22 default-cost 6
#
# after:
#     processes:
#     - process_id: '10'
#     - process_id: '26'
#     - process_id: '27'
#     - process_id: '30'

# After state:
# ------------
#
# RP/0/RP0/CPU0:anton(config)#show running-config router ospf
# Thu Jun 11 17:07:34.218 UTC
# router ospf 10
#  area 11
#  !
#  area 22
#  !
# !
# router ospf 26
# !
# router ospf 27
#  area 10
#  !
#  area 20
#  !
# !
# router ospf 30
#  area 11
#  !
#  area 22
#  !
# !


# Using parsed
# parsed.cfg
# ------------
# Thu Jun 11 17:28:51.918 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  authentication message-digest keychain ansible1101pass
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#   authentication keychain ansi11393
#   hello-interval 2
#  !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
#
- name: Parsed the device configuration to get output commands
  cisco.iosxr.iosxr_ospfv2:
    running_config: "{{ lookup('file', './parsed.cfg') }}"
    state: parsed
#
# Task Output:
# ------------
#
# parsed:
#     processes:
#     - areas:
#       - area_id: '11'
#         cost: 11
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       authentication:
#         keychain: ansible_test1102
#       process_id: '10'
#     - adjacency_stagger:
#         max_adjacency: 20
#         min_adjacency: 10
#       authentication:
#         message_digest:
#           keychain: ansible1101pass
#       process_id: '26'
#     - areas:
#       - area_id: '10'
#         authentication:
#           keychain: ansi11393
#         hello_interval: 2
#       process_id: '27'
#     - areas:
#       - area_id: '11'
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       cost: 2
#       dead_interval: 2
#       default_metric: 10
#       demand_circuit: enable
#       external_out: disable
#       flood_reduction: disable
#       hello_interval: 1
#       mtu_ignore: enable
#       packet_size: 577
#       passive: disable
#       priority: 1
#       process_id: '30'
#       retransmit_interval: 2
#       router_id: 2.2.2.2
#       summary_in: enable
#       transmit_delay: 2
#       weight: 2

# Using rendered
#
- name: Render the commands for provided  configuration
  cisco.iosxr.iosxr_ospfv2:
    config:
      processes:
        - process_id: 27
          areas:
            - area_id: 10
              hello_interval: 2
              authentication:
                keychain: ansi11393
        - process_id: 26
          adjacency_stagger:
            min_adjacency: 10
            max_adjacency: 20
        - process_id: 10
          authentication:
            keychain: ansible_test1102
          areas:
            - area_id: 11
              default_cost: 5
              cost: 11
            - area_id: 22
              default_cost: 6
        - process_id: 30
          areas:
            - area_id: 11
              default_cost: 5
            - area_id: 22
              default_cost: 6
          cost: 2
          default_metric: 10
          transmit_delay: 2
          hello_interval: 1
          dead_interval: 2
          retransmit_interval: 2
          weight: 2
          packet_size: 577
          priority: 1
          router_id: 2.2.2.2
          demand_circuit: enable
          passive: disable
          summary_in: enable
          flood_reduction: disable
          mtu_ignore: enable
          external_out: disable
    state: rendered


#
# Task Output:
# ------------
#
# rendered:
#   - router ospf 27
#   - area 10 authentication keychain ansi11393
#   - area 10 hello-interval 2
#   - router ospf 26
#   - adjacency stagger 10 20
#   - router ospf 10
#   - authentication keychain ansible_test1102
#   - area 11 default-cost 5
#   - area 11 cost 11
#   - area 22 default-cost 6
#   - router ospf 30
#   - cost 2
#   - weight 2
#   - passive disable
#   - priority 1
#   - flood-reduction disable
#   - default-metric 10
#   - router-id 2.2.2.2
#   - demand-circuit enable
#   - packet-size 577
#   - transmit-delay 2
#   - summary-in enable
#   - external-out disable
#   - dead-interval 2
#   - hello-interval 1
#   - retransmit-interval 2
#   - mtu-ignore enable
#   - area 11 default-cost 5
#   - area 22 default-cost 6


# Using gathered
#
# Before state:
# -------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 16:06:44.406 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#   authentication keychain ansi11393
#   hello-interval 2
#  !
#  area 20
#  !
# !
# router ospf 30
#  router-id 2.2.2.2
#  summary-in enable
#  external-out disable
#  cost 2
#  packet-size 577
#  weight 2
#  passive disable
#  priority 1
#  mtu-ignore enable
#  flood-reduction disable
#  dead-interval 2
#  retransmit-interval 2
#  demand-circuit enable
#  hello-interval 1
#  transmit-delay 2
#  default-metric 10
#  area 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
#
- name: Gather ospfv2 routes configuration
  cisco.iosxr.iosxr_ospfv2:
    state: gathered
#
#
# Task Output:
# ------------
#
# gathered:
#     processes:
#     - areas:
#       - area_id: '11'
#         cost: 11
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       authentication:
#         keychain: ansible_test1102
#       process_id: '10'
#     - adjacency_stagger:
#         max_adjacency: 20
#         min_adjacency: 10
#       process_id: '26'
#     - areas:
#       - area_id: '10'
#         authentication:
#           keychain: ansi11393
#         hello_interval: 2
#       process_id: '27'
#     - areas:
#       - area_id: '11'
#         default_cost: 5
#       - area_id: '22'
#         default_cost: 6
#       cost: 2
#       dead_interval: 2
#       default_metric: 10
#       demand_circuit: enable
#       external_out: disable
#       flood_reduction: disable
#       hello_interval: 1
#       mtu_ignore: enable
#       packet_size: 577
#       passive: disable
#       priority: 1
#       process_id: '30'
#       retransmit_interval: 2
#       router_id: 2.2.2.2
#       summary_in: enable
#       transmit_delay: 2
#       weight: 2
#
# After state:
# -------------
#
# RP/0/RP0/CPU0:anton#show running-config router ospf
# Thu Jun 11 16:06:44.406 UTC
# router ospf 10
#  authentication keychain ansible_test1102
#  area 11
#   cost 11
#   default-cost 5
#  !
#  area 22
#   default-cost 6
#  !
# !
# router ospf 26
#  authentication message-digest keychain ansible1101pass
#  adjacency stagger 10 20
# !
# router ospf 27
#  area 10
#  authentication keychain ansi11393
#   hello-interval 2
# !
# !
# router ospf 30
# router-id 2.2.2.2
# summary-in enable
# external-out disable
# cost 2
# packet-size 577
# weight 2
# passive disable
# priority 1
# mtu-ignore enable
# flood-reduction disable
# dead-interval 2
# retransmit-interval 2
# demand-circuit enable
# hello-interval 1
# transmit-delay 2
# default-metric 10
# area 11
#  default-cost 5
# !
# area 22
#  default-cost 6
# !
# !
#

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key	Description
after dictionary	The resulting configuration model invocation. Returned: when changed Sample: "The configuration returned will always be in the same format\n of the parameters above.\n"
before dictionary	The configuration prior to the model invocation. Returned: always Sample: "The configuration returned will always be in the same format\n of the parameters above.\n"
commands list / elements=string	The set of commands pushed to the remote device. Returned: always Sample: ["router ospf 30", "authentication message-digest keychain 'ansible1101pass'"]
gathered dictionary	Facts about the network resource gathered from the remote device as structured data. Returned: when state is gathered Sample: "This output will always be in the same format as the module argspec.\n"
parsed dictionary	The device native config provided in running_config option parsed into structured data as per module argspec. Returned: when state is parsed Sample: "This output will always be in the same format as the module argspec.\n"
rendered list / elements=string	The provided configuration in the task rendered in device-native format (offline). Returned: when state is rendered Sample: ["router ospf 27", "area 10 authentication keychain ansi11393"]

Authors

• Rohit Thakur (@rohitthakur2590)

Collection links

• Issue Tracker
• Repository (Sources)