community.network.ce_is_is_interface – Manages isis interface configuration on HUAWEI CloudEngine devices.

Note

This plugin is part of the community.network collection (version 3.0.0).

You might already have this collection installed if you are using the ansible package. It is not included in ansible-core. To check whether it is installed, run ansible-galaxy collection list.

To install it, use: ansible-galaxy collection install community.network.

To use it in a playbook, specify: community.network.ce_is_is_interface.

New in version 0.2.0: of community.network

Synopsis

  • Manages isis process id, creates a isis instance id or deletes a process id on HUAWEI CloudEngine devices.

Parameters

Parameter Choices/Defaults Comments
bfdblocken
boolean
    Choices:
  • no
  • yes
Blocking interfaces to dynamically create BFD features. The value is a bool type.
bfdstaticen
boolean
    Choices:
  • no
  • yes
Configure static BFD on a specific interface enabled with ISIS. The value is a bool type.
ifname
string / required
A L3 interface.
instance_id
integer / required
Specifies the id of a isis process. The value is a number of 1 to 4294967295.
level1cost
integer
Specifies the link cost of the interface when performing Level-1 SPF calculation. The value is a number of 0 to 16777215.
level1dispriority
integer
the dispriority of the level1. The value is a number of 1 to 127.
level2cost
integer
Specifies the link cost of the interface when performing Level-2 SPF calculation. The value is a number of 0 to 16777215.
level2dispriority
integer
the dispriority of the level1. The value is a number of 1 to 127.
leveltype
string
    Choices:
  • level_1
  • level_2
  • level_1_2
level type for three types.
p2pnegotiationmode
string
    Choices:
  • 2_way
  • 3_way
  • 3_wayonly
Set the P2P neighbor negotiation type.
p2ppeeripignore
boolean
    Choices:
  • no
  • yes
When the P2P hello packet is received, no IP address check is performed. The value is a bool type.
ppposicpcheckenable
boolean
    Choices:
  • no
  • yes
Interface for setting PPP link protocol to check OSICP negotiation status. The value is a bool type.
silentcost
boolean
    Choices:
  • no
  • yes
Specifies whether the routing cost of the silent interface is 0. The value is a bool type.
silentenable
boolean
    Choices:
  • no
  • yes
enable the interface can send isis message. The value is a bool type.
snpacheck
boolean
    Choices:
  • no
  • yes
Enable SNPA check for LSPs and SNPs. The value is a bool type.
state
string
    Choices:
  • present ←
  • absent
Determines whether the config should be present or not on the device.
typep2penable
boolean
    Choices:
  • no
  • yes
Simulate the network type of the interface as P2P. The value is a bool type.

Notes

Note

  • Interface must already be a L3 port when using this module.

  • This module requires the netconf system service be enabled on the remote device being managed.

  • This module works with connection netconf.

Examples

- name: "create vlan and config vlanif"
  ce_config:
    lines: 'vlan {{ test_vlan_id }},quit,interface {{test_intf_vlanif}},ip address {{test_vlanif_ip}} 24'
    match: none

- name: "create eth-trunk and config eth-trunk"
  ce_config:
    lines: 'interface {{test_intf_trunk}},undo portswitch,ip address {{test_trunk_ip}} 24'
    match: none

- name: "create vpn instance"
  ce_config:
    lines: 'ip vpn-instance {{test_vpn}},ipv4-family'
    match: none

- name: Set isis circuit-level
  community.network.ce_is_is_interface:
    instance_id: 3
    ifname: Eth-Trunk10
    leveltype: level_1_2
    state: present

- name: Set isis level1dispriority
  community.network.ce_is_is_interface:
    instance_id: 3
    ifname: Eth-Trunk10
    level1dispriority: 0
    state: present

- name: Set isis level2dispriority
  community.network.ce_is_is_interface:
    instance_id: 3
    ifname: Eth-Trunk10
    level2dispriority: 0
    state: present

- name: Set isis silentenable
  community.network.ce_is_is_interface:
    instance_id: 3
    ifname: Eth-Trunk10
    silentenable: true
    state: present

- name: Set vpn name
  ce_is_is_instance:
    instance_id: 22
    vpn_name: vpn1
    state: present

Return Values

Common return values are documented here, the following are the fields unique to this module:

Key Returned Description
changed
boolean
always
check to see if a change was made on the device

Sample:
True
end_state
dictionary
always
k/v pairs of configuration after module execution

Sample:
{'session': {'addrType': 'IPV4', 'createType': 'SESS_STATIC', 'destAddr': None, 'outIfName': '10GE1/0/1', 'sessName': 'bfd_l2link', 'srcAddr': None, 'useDefaultIp': 'true', 'vrfName': None}}
existing
dictionary
always
k/v pairs of existing configuration

Sample:
{'session': {}}
proposed
dictionary
always
k/v pairs of parameters passed into module

Sample:
{'addr_type': None, 'create_type': None, 'dest_addr': None, 'out_if_name': '10GE1/0/1', 'session_name': 'bfd_l2link', 'src_addr': None, 'state': 'present', 'use_default_ip': True, 'vrf_name': None}
updates
list / elements=string
always
commands sent to the device

Sample:
['bfd bfd_l2link bind peer-ip default-ip interface 10ge1/0/1']


Authors

  • xuxiaowei0512 (@CloudEngine-Ansible)